Filter Results By:
Products
Applications
Manufacturers
-
product
PCI Express Receiver Board
AD12-2000-IRIGB
The AD12-2000-IRIGB is a high performance wideband 0.3-1.8GHz PCIe-bus receiver on a single PCIe Gen3 board, that can continuously digitize a wide portion of the RF spectrum, with a 3.6GSPS 12-bit A/D that can be synchronized with stability of better than +/- 100 picoseconds with respect to an IRIG-B 1PPS signal and global time codes from a satellite receiver or local site time reference. Designed for demanding military, scientific, industrial, communications, safety and electrical power utility applications, the AD12-2000-IRIGB has 60dB of gain adjust range (manual and AGC with programmable loop bandwidth), a wideband noise figure of 9dB, +11dBm 1dB compression point, and 2dB peak-to-peak ripple over the 300MHz to 1.6GB frequency spectrum.
-
product
0.1Hz-3.7GHz Frequency Counter
FC-3000
Features:*Frequency measuring range: 0.1Hz to 100MHz in A input, 80 MHz to 3.0GHz in C input.*Period,Total and RPM measurement for input A*9 Digit display with 0.01mHz resolution in 1 Sec (By Ext.Reference signal).*RS-232C serial interface function for communication with computer.*High sensitivity Extemal reference input function(>=1.5Vrms).*Peciprocal technique for high resolution at low counting frequencies .*Self check function executed to perform a automatic self diagnosis of various counter function.*Push-scanning for selecting Function and Gate time.*Low-pass filter(100KHz,-3dB)installed for removing noise signsl in low frequency measuring.*AC/DC coupling function(Selectable AC/CD Coupling)*10:1 Input Attenuation(Selectable×1/×10 Attenuator)*Data hold function
-
product
Embedded LO Capability
S96084B
Enables accurate measurement of relative phase and absolute group delay of a frequency converter with a built-in LO source, without having to access a common reference signal
-
product
SENSORBOX MODULE
MDGDSSBM
*Turn your MDMAX, MDMAX2A or MDMAX3 into a unique sensor simulator to substitute known good waveforms for intermittent components that cannot be verified*Sensor simulation tests include: DC voltage, fixed frequency, pre-defined waveform and hand-drawn waveform*Contains a library of standard reference waveforms that can be modified by the stroke of a finger
-
product
3-Slot Data Acquisition Mainframe With GPIB And Three 20-Channel Multiplexer Modules
DAQ973MB
The DAQ973MB Better Multiplexer Bundle offer includes a DAQ973A three-slot data acquisition mainframe and three 20-channel DAQM901A multiplexer modules. This bundle provides the following:3-slot mainframe with USB, LAN, and GPIB6.5-digit (22-bit) internal DMM60 channels of multiplexer switches6 channels of dedicated current measurements2- and 4-wire scanning300 V switching80 channels/s scanningbuilt-in thermocouple reference junctionbuilt-in signal conditioning to measure thermocouples, RTDs and thermistors, AC / DC volts and current; resistance, frequency / period, diode test, and capacitance
-
product
Channelized Up-Converter
UPCV Series 5” x 2.5” x 0.6”
*Connectorized Package *Wide Choice of Frequency Ranges *IF to Ka-Band Solutions Available *Integrated Filters *Gain Control *USA, RS232 or SPI Control *Internal / External References *Low Power Consumption *Low Phase Noise *Low Spurs
-
product
Seismic Sensors & Transducers
Displacement Pickups are vibration transducers that incorporate a spring-mass system with eddy-current damping using a frictionless pivot. This pivot is a spring flexure that serves as the ‘spring’ and a moment arm attached to the pivot serves as the ‘mass’, which allows resolutions down to the micro inch range. At frequencies above 50Hz, the mass remains fixed in space and becomes an inertial reference. A transducer within the pickup senses the motion of the mounting base relative to the inertial reference and converts it into a proportional signal. Appropriate damping results in a frequency response flat down to 10 Hz. Note that the pickup senses in only one plane, which is perpendicular to the mounting base.
-
product
1202a High Frequency Distribution
Precise Time and Frequency, Inc.
The ptf 1202A High Frequency Distribution amplifier provides high performance frequency references for laboratory or system use requiring distribution at frequencies of 30MHz and above.The ptf 1202A is especially designed to distribute the high frequency input signal to 12 separate outputs, with minimum signal distortion and maximum isolation between individual output signals.
-
product
Rubidium Reference Oscillator
LPFRS-01
Rubidium reference generator LPFRS-01 is designed to generate a highly stable reference and clock frequency signal.
-
product
VME Time & Frequency Processor
VME635091-SyncClock
Brandywine Communications’ VME635091-SYNCCLOCK is a time and frequency processor module that provides precision time and frequency reference to the host computer and peripheral data acquisition systems. Time is acquired from time code signals, typically IRIG B. Time is displayed on the front panel (hours, minutes, seconds) via LED digits.
-
product
Saturable Spectroscopy Laser Lock Module
A compact, mechanically-robust laser frequency reference.
-
product
Signal Analysis
Harmonic Distortion Analysis
The software is used for automatic measurement of the harmonic distortion factor and voltage r.m.s. of signals coming to the input channels of FFT spectrum analyzers. Adjustment to the frequency of the main component is performed automatically. The program is based on the measurement of the voltage r.m.s. of higher components by an external or internal reference signal.
-
product
AC Reference Modules
NAI offers a variety of AC reference modules that provide a drive capability to 5 VA. The units are transformer-isolated and operate over a frequency range from 47 Hz to 10 kHz. These modules are specifically designed for rugged defense, commercial aerospace, and industrial applications.
-
product
Intelligent Reference
TM-4D
The Intelligent Reference/TM-4D™ breaks new ground for time and frequency references. For the first time, it is possible to generate and distribute both analog and digital signals to multiple instruments and locations with just one product that fits in a single rack space. The TM-4D is three instruments in one: an Intelligent Reference/TM-4™ precise time and frequency reference, a digital signal distribution amplifier and an analog distribution amplifier. And it eliminates the need for multiple boxes.
-
product
16 Bit DDS Generator Up To 200 MHz
96xx series
The 96xx series DDS generators deliver the highest performance in both speed and resolution. The series includes produts between one and 24 synchronous channels. DDS – Direct Digital Synthesis – is a method for generating sine waves from a single, fixed-frequency reference clock and is widely used in signal generation applications. The DDS functionality implemented on Spectrum Instrumentation’s AWG platform is based on the principle of adding multiple “DDS cores” to generate a mul?ti-carrier (multi-tone) signal, with each carrier having its own well-defined frequency, amplitude and phase. In addition to these static parameters, there are also build in dynamic parameters like frequency slope and amplitude slope to allow for intrinsic linear changes for multiple cores.
-
product
Universal Counter
U6220A
The Picotest U6200A also provides great features including Frequency & Ratio (11Digits/Sec.), Time interval, Period (2.5 ns to 1000s), Duty Cycle, Pulse Width, Rise/Fall Time, Peak Volts (100 Hz~300 MHz), Phase, Totalize, Temperature Stability (< 1 PPM), Aging Rate (< 2 PPM per year), timebase reference channel (Figure-2) and complete Front-End Isolation. Moreover, it offers 20 memory locations (Figure-3) for storing frequently-used operations.
-
product
Optical Chopper
SR540
Stanford Research Systems, Inc.
The SR540 chopper will handle all your optical chopping requirements?from simple measurements to dual-beam and intermodulation experiments. The SR540 has a 4-digit frequency display, front-panel frequency control, analog voltage frequency control and two reference outputs with selectable operating modes.
-
product
Comb Generator, 10 MHz To 110 GHz
U9391M
U9391M comb generators were developed to provide precision phase calibration, for non-linear measurements using the PNA-X nonlinear vector network analyser (NVNA), referenced to the National Institute of Standards and Technology (NIST) standard. Additionally, the comb generators can be used to calibrate PNA and PNA-X network analyzers for phase and delay measurements of frequency converters without requiring reference or calibration mixers.
-
product
2210A & 2211A Quartz Frequency Standards
Precise Time and Frequency, Inc.
The ptf 2210A Quartz Frequency Standard has been designed to provide a highly stable and spectrally pure frequency reference for applications requiring the ultimate in short term frequency performance.The instrument contains a double oven controlled stress compensated (SC cut) quartz crystal oscillator (OCXO) to give the ultimate in performance.Ideal for laboratory or system use, the unit provides good stability performance at lower cost and with improved phase noise.
-
product
Hydrophone
RESON TC4013
The TC4013 offers a usable frequency range of 1Hz to 170kHz and a high sensitivity relative to its size. It further-more provides uniform omnidirectional sensitivities in both horizontal and vertical planes up to high frequencies.The TC4013 is an excellent transducer for making absolute sound measurements and calibrations within a broad frequency range. It can also be applied as an omnidirectional reference projector.The overall characteristics makes TC4013 extremely applicable for laboratory as well as industrial uses.
-
product
Quad RF Driver
The Quad RF Driver contains four independent RF channels, each with an RF synthesizer, variable attenuator, and 1W power amplifier. The RF signal can originate from either the internal synthesizer or an external source via SMA input. All channels have independent frequency, phase, and gain settings and can be operated in one of two modes. The “Wideband” mode operates from 35MHz to 2GHz with a 3.472KHz resolution; over this range the frequency roll-off is approximately 0.5dB/100MHz. “Int-N Phase Adjust” mode allows the user to set and maintain a fixed phase relationship between all four channels. This mode is designed to operate between 300 and 460MHz with a 2MHz resolution. Two additional inputs are provided for an external frequency reference and digital modulation.
-
product
PXIe Frequency Reference: 10 MHz And 100 MHz
M9300A
The M9300A PXIe frequency reference is a PXIe-compatible, compact, modular instrument that can be used with the Keysight M9301A synthesizer, M9310A source output, and M9311A modulator to create the world’s fastest vector signal generator, the M9381A. Create a CW source, the M9380A, by combining the M9300A with the M9301A and M9310A or use it as the 10-MHz or 100-MHz reference with other PXI solutions. Control the instrument through a soft front panel and programmatic interfaces tuned to your application development environment of choice.
-
product
Frequency Standard Products
The ES-110 generates a stable source of 10 MHz using GPS (Global Positioning System) satellites as a reference. If frequency distribution is needed, we offer the ES-210, a Quad 1x6 1/5/10 MHz Distribution Amplifier. The ES-210 provides four independent 1x6 Frequency DAs in a single rack-mount enclosure. The ES-410 is a four output version of the ES-110. The ES-410 was introduced and won Radio Magazine's Best of Show Award at the 2016 NAB Show.
-
product
Comb Generator, 10 MHz to 50 GHz
U9391F
The Keysight Technologies, Inc. U9391F comb generators were developed to provide precision phase calibration, for non-linear measurements using the PNA-X nonlinear vector network analyser (NVNA), referenced to the National Institute of Standards and Technology (NIST) standard. Additionally, the comb generators can be used to calibrate PNA and PNA-X network analyzers for phase and delay measurements of frequency converters without requiring reference or calibration mixers.
-
product
Rubidium Atomic Audio Clock
PERF10
Stanford Research Systems, Inc.
Perfection is a high standard - but your studio clocks deserve nothing less. That''s why we designed the PERF10, to offer audio professionals and demanding audiophiles a frequency reference of staggering accuracy and unmatched stability.
-
product
Regeneration Station
This equipment is a stand-alone device that enables to coherently regenerate an optical signal allowing long-haul dissemination of an ultra-stable optical frequency reference. Its architecture is based on the heterodyne phase-locking of a narrow spectral width laser diode on the reference signal. The station is equipped with low phase noise optical interferometer that perform a thorough characterization of the phase noise accumulated by the incoming signal, and a compensation system of this phase noise.
-
product
Quantum & Metrology Instruments
Beyond quantum sensors, Exail’s photonics solutions enable real applications in other quantum technology fields. They also enable precise control and transmission of the frequency, phase and amplitude of a laser light through fibered telecommunication links, for metrology applications. The true and deep understanding of Exail teams for the fundamental physics behind its technology explains the absolute quality of its time & frequency reference products.
-
product
Spectral Phase Measurement
Avoca SPIDER System
Spectral phase interferometry for direct electric-field reconstruction (SPIDER) is one technique that can recover the spectral phase of an input pulse, without needing any reference pulse. SPIDER interferes two pulses which areseparated in time and in frequency, and the resultantinterferogram is read by a spectrometer.
-
product
Video Transmitter
Model: DS-5210
The S-Band Video Transmitter is a synthesized microwave signal source providing low phase noise with a high level signal output. The unit can be set to any frequency within the band of design via a USB or RS-232/422/485 computer command. The oscillator is phase locked to an internal TCXO reference. The oscillator pro-vides a stable low noise source for video transmission.
-
product
Remote Spectrum Analyzers
LPT-3000RX4
Latest DSP Technology; 9 kHz to 3 GHz Frequency Range; External 10 MHz Reference; 17 RBW filters Down to 1 Hz; 17 VBW filters Down to 1 Hz; > 88 dBm Dynamic Range; High Definition Spectrum Trace; 55 dBm Input Port Isolation; 50 dBm input attenuator; 0.5 millisecond Port Switch Speed; Available in 4, 8 or 16 RF inputs; Optional Internal Carrier Identification CID module; Optional Internal Down Converter modules
