Filter Results By:
Products
Applications
Manufacturers
General Purpose Switch
is an array of uncommitted relays. AKA: General Purpose Switching
See Also: Switching, Switching Matrix, High Voltage Switching, Switching Matrices, Multiplexers
-
product
EtherCAT Chassis with EtherCAT Bus-Coupler
EPS-9905 with EPS-6000
ADLINK" s EPS slave system features modular design for flexible high channel density, rugged construction, easy maintenance, and intelligent performance, compatible with 3rd party EtherCAT products. Precise time-deterministic control enables I/O synchronization for critical applications, and FPGA and ARM technology allow users to fully monitor status of EPS modules and systems, including operating temperature and usage cycle of relay switching, as well as motion control status for general purpose motor drive control. In addition, the ADLINK EtherCAT configurator enables auto-scan and configuration across EtherCAT systems. The EPS" unique structural and electronic design supports hot-swappable function, reducing repair time, and the rugged construction and operating temperature range of -20°C to 60°C allow operation in the harshest environments.
-
product
PXI SPST Switch: 50-ch, 100Vrms/1A, Reed Relays
M9132A
The M9132A is a high-density, general purpose switch with50 independent, single-pole, single-throw (Form A) switches in a single PXI module. This module can be used to cycle power to products under test, control indicator and status lights or actuate external power relays and solenoids. The high-speed, long-life reed relays can handle 100Vrms and 1A, with up to 25W power. Choose from the durable connector block or standard cable connections.
-
product
PXI 8x SPST High Voltage Reed Relays
40-310-001
The 40-310/320 range of high voltage switching modules will hot switch up to 750V peak and cold switch up to 1000V peak in either general purpose relay (40-310) or multiplexer (40-320) configurations. These modules contain high-quality reed relays with switching ratings comfortably higher than the 40-310/320 specification. Applications include; circuit board isolation testing, relay testing, semiconductor breakdown monitoring and cable harness insulation testing.
-
product
Ruggedized Field Deployable Tester
PUMA
- 18-slot PXI / 4-slot SCXI Chassis- 1.2 GHz Embedded Controller- 4-axis Motion Controller/Simulation- 8-port RS-232 Serial Module- 4-port RS-485 Serial Module- 48 bit Isolated Digital I/O- Reconfigurable multi-function I/O FPGA Module- 5 1/2 digit DMM- 200 MHz 2-channel Scope/Digitizer- Multi-function Data Acquisition (DAQ)- 8-channel Analog Input Module- 6-channel Analog Output Module- General Purpose Switching- RF suite (optional)
-
product
PXI Multiplexer, Single 48-Channel, 1-Pole
40-632A-021-48/1
The 40-632A-021-48/1 is a single 48-channel, 1-pole PXI multiplexer and is part of our series of general purpose multiplexer modules featuring a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems.
-
product
PXI High Voltage Multiplexer, 24-Channel
40-320A-101
The 40-320A-101 is a single 24-channel MUX and is part of our 40-310/320A range of High Voltage Switching Modules which will hot switch up to 750V peak and cold switch up to 1000V peak in either general purpose relay (40-310) or multiplexer (40-320A) configurations.
-
product
Low-Density PXI Switch Matrix Modules
Our low-density PXI switch matrix modules are a cost-effective solution for applications that require relatively small matrices in the PXI format. These low-density switch matrices can be expanded by connecting together multiple modules, however, we recommend that users look at the higher density switch matrix modules that involve less user configuration. Reed relay versions use high quality sputtered ruthenium relays that exhibit excellent contact performance under low and medium level switching conditions. For general purpose applications that also require higher power handling, the range of electro-mechanical relays provides an ideal solution.
-
product
Microwave Power Amplifiers
Spanawave/Giga-tronics Microwave Power Amplifiers deliver outstanding performance and exceptional value. These ultra-broadband amplifiers have excellent pulse performance and modulated signal fidelity, ideal for testing in wireless communications, defense EW and radar testing and general purpose microwave laboratory applications. Have the power you need to overcome cable and switching losses, or to drive higher power mixers, detectors and very high power amplifiers.
-
product
PXI General Purpose 2A Relay Module 16xSPST
40-132-101
Pickering Interfaces 40-131/132 modules are a range of low cost, general purpose electromechanical relay cards. They are capable of switching voltages up to 300VDC/250VAC and current up to 2A. They are suitable for use where reed relay based switching cards do not have sufficient voltage or current carrying capability. Applications include the switching of medium power AC and DC loads, or slave switching larger relays, contactors or solenoids. Connections are made to the card via a front panel mounted 78 pin D-Type connector plug.
-
product
PXI Low-Density General Purpose Switch Modules
These PXI low-density general purpose switch modules provide cost-effective solutions for applications where a high number of relays is not required. All of these modules use a 96 pin male connector that is supported by our comprehensive range of cable and connector accessories, ensuring they can be quickly integrated into your test system with minimum effort.
-
product
2-CH Pulse-Train Motion Control EtherCAT Module
EPS-7002
ADLINK" s EPS slave system features modular design for flexible high channel density, rugged construction, easy maintenance, and intelligent performance, compatible with 3rd party EtherCAT products. Precise time-deterministic control enables I/O synchronization for critical applications, and FPGA and ARM technology allow users to fully monitor status of EPS modules and systems, including operating temperature and usage cycle of relay switching, as well as motion control status for general purpose motor drive control. In addition, the ADLINK EtherCAT configurator enables auto-scan and configuration across EtherCAT systems. The EPS" unique structural and electronic design supports hot-swappable function, reducing repair time, and the rugged construction and operating temperature range of -20°C to 60°C allow operation in the harshest environments.
-
product
LXI And LXI/USB Modular Chassis
Our LXI modular chassis are available in 7 and 18-slot and our LXI/USB modular chassis are available in 2, 4 and 6-slot and support over 1,000 of our PXI modules. The PXI modules supported range from: PXI general purpose relays, matrices, multiplexers and RF switches to special PXI switching functions such as fault/signal insertion. Also supported are a selection of simulation modules such as programmable resistors, digital I/O, power supplies, thermocouple simulators, function generator, battery simulators and attenuators. This gives you enormous flexibility to define a switching or T&M system to exactly match your needs.
-
product
PXI Multiplexer, Dual 24-Channel, 1-Pole
40-632A-021-D/24/1
The 40-632A-021-D/24/1 is a dual 24-channel, 1-pole PXI multiplexer and is part of our series of general purpose multiplexer modules featuring a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems.
-
product
PXI SPST Switch: 100-ch, 100Vrms/1A, Reed Relays
M9133A
The M9133A is a high-density, general purpose switch with 100 independent, single-pole, single-throw (Form A) switches in a single PXI module. This module can be used to cycle power to products under test, control indicator and status lights or actuate external power relays and solenoids. The high-speed, long-life reed relays can handle 100Vrms and 1A, with up to 25W power. Choose from the durable connector block or the standard cable connections.
-
product
PXI SPDT Switch: 26-ch, 2A, Armature Relay
M9130A
The M9130A is a general purpose switch with 26 independent, single-pole, double-throw (Form C) switches in a single PXI module. This module can be used to cycle power to products under test, control indicator and status lights or actuate external power relays and solenoids. The armature relays can handle up to 60W power. When needed, these relays can handle up to 6A pulsed carry current. Choose from the durable connector block or standard cable connections.
-
product
PCI 39xSPST 2Amp Relay Card
50-132-003
The 50-132-003 39xSPST relay module is part of our range of PCI, low cost, general purpose electro-mechanical relay modules which are capable of switching voltages up to 300VDC/250VAC and current up to 2A. They are suitable for use where reed relay based switching modules do not have sufficient voltage or current carrying capability.
-
product
Multifunction Switch / Measure Unit, Modules
34980A
The 34980A General Purpose switches can be used to route signals or to control other devices in an application. These switches are ideal for device actuation, switching loads or power supplies. Both switches offer high power channels up to 150W. The general purpose modules also include a relay switch counter to help predict when relays need to be replaced.
-
product
PXI Multiplexer, Dual 16-Channel, 2-Pole
40-630A-022-D/16/2
The 40-630A-022-D/16/2 is a dual 16-channel, 2-pole PXI multiplexer and is part of our series of general purpose multiplexer modules featuring a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems.
-
product
PXI 12 x DPST Reed Relay 2.5 Amp
40-136-012
The 40-136-012 12xDPST reed relay module is part of our range of medium power, general purpose relay modules which are capable of switching voltages up to 200V and current up to 2.5A.
-
product
Optoelectronics
Renesas provides a wide range of optoelectronic devices, including IC output photocouplers (optocouplers) featuring a high response from 1Mbps to 15Mbps, as well as general purpose transistor output devices featuring high isolation voltage, high temperature operation and compliance with various international safety standards. For motor drive applications, dedicated photocouplers provide high isolation voltage, high temperature operation, high output current, and high-speed switching. These are complemented by a diverse range of ultra-high speed devices for fiber-optic applications, as well as solid state relays (OCMOS FETs).
-
product
PXI Multiplexer Single 48 Ch 1 Pole
40-632-021-48/1
This series of general purpose multiplexer modules feature a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 68-pin connector. Available reed relay formats are 1-pole, 2-pole and 1-pole screened.
-
product
8-CH ±10V Analog Output EtherCAT Module
EPS-4008
ADLINK" s EPS slave system features modular design for flexible high channel density, rugged construction, easy maintenance, and intelligent performance, compatible with 3rd party EtherCAT products. Precise time-deterministic control enables I/O synchronization for critical applications, and FPGA and ARM technology allow users to fully monitor status of EPS modules and systems, including operating temperature and usage cycle of relay switching, as well as motion control status for general purpose motor drive control. In addition, the ADLINK EtherCAT configurator enables auto-scan and configuration across EtherCAT systems. The EPS" unique structural and electronic design supports hot-swappable function, reducing repair time, and the rugged construction and operating temperature range of -20°C to 60°C allow operation in the harshest environments.
-
product
64-Channel Form A General Purpose Switch for 34980A
34939A
The Keysight 34939A is a high density general-purpose switch module for the 34980A Multifunction Switch/Measure Unit. It has 64 independent single-pole, single-throw (SPST) relays that can switch 1A and carry 2A. This module can be used to cycle power to products under test, control indicator and status lights, and to actuate external power relays and solenoids. The relays are 100V, 1A contacts and can handle up to 60W. Standard 78-pin Dsub connectors allow for use with standard cables, screw terminal blocks, or mass interconnect solutions.
-
product
PXI 32 x SPDT Reed Relay
40-110-121
Our 40-110 and 40-115 range of reed relay switching modules are available in both Changeover (SPDT) and Normally Open (SPST & DPST) configurations. Connections are made via a front panel 96 pin male micro-D connector. For applications requiring improved bandwidth and crosstalk performance please look at our 40-120/125 range of shielded reed relay cards. General purpose reed relays are suitable for the construction of small switching networks, for slaving up to larger switches or for operating external devices (e.g. lamps, solenoids etc.). To simplify inter-relay wiring, interconnection points are built onto the circuit board thus easing the construction of complicated wiring.
-
product
PXI Multiplexer Dual 16 Ch 2 Pole
40-630-022-D/16/2
This series of general purpose multiplexer modules feature a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 68-pin connector. Available reed relay formats are 1-pole, 2-pole and 1-pole screened.
-
product
General Purpose Functional Test Systems
Keysight Technologies’ TS-5000 Family of Electronics Functional Test Systems offers a wealth of choices in general purpose instruments, power supplies, switch loading and DIO capabilities in a multiple rack heights, seamlessly connected with open architecture software Test Exec SL, all immaculately assembled and thoroughly tested so you don’t have to.
-
product
PXI SPST Power Relay: 20-ch, 5A, 300W
M9135A
The M9135A is a general purpose switch with 20 independent, single-pole, single-throw (Form A) switches in a single PXI module. This module is ideal for switching heavy loads or power supplies including voltages mains or DC current. The heavy-duty armature relays are rated for up to 5A and 300W, enough for inductive or capacitive loads. Choose from the heavy-duty power connector or an unterminated power cable.
-
product
PXI/PXIe High Density Reed Relay Module, 75xSPST
42-140B-121
The 40-140B-121 (PXI) and 42-140B-121 (PXIe) are 75xSPST general purpose switching modules. They are part of a range of high density relay modules using ruthenium reeds available in 50x, 75x and 100x Normally Open SPST configurations. Connections are made via a front panel 200-pin female connector.
-
product
PXI 12 Channel High Voltage Multiplexer
40-320-001
The 40-310/320 Range of High Voltage Switching Modules will hot switch up to 750V peak and cold switch up to 1000V peak in either general purpose relay (40-310) or multiplexer (40-320) configurations. These modules contain high-quality reed relays with switching ratings comfortably higher than the 40-310/320 specification. Applications for the 40-310/320 series modules include; circuit board isolation testing, relay testing, semiconductor breakdown monitoring and cable harness insulation testing.
-
product
High Density, 80-Channel Switch Card
1260-17
The Astronics 1260-17 is an 80-channel, Form C (SPDT) switch module offering general purpose switching and external device actuation. Each channel may be configured individually, or several channels may be linked to configure custom networks. The 1260-17 permits switching up to 1 amp and 250V DC or VACrms per channel.
