Filter Results By:
Products
Applications
Manufacturers
HF
High Frequency operating at 3–30 MHz.
-
product
Lock-in Amplifier
HF2LI
The Zurich Instruments HF2LI (high-frequency, 2 inputs) is a digital lock-in amplifier covering the frequency range between DC and 50 MHz. It features 2 physical input channels so that it can replace 2 devices in many measurement setups. The 128-bit digital signal processing delivers superior precision thus boosting both the noise performance and the dynamic reserve. With these unprecedented capabilities, the HF2LI brings lock-in amplification to a new level and enables new applications in a frequency range that was previously tied to analog instrumentation. The computer is connected by a high-speed USB interface, which allows data acquisition at high rates. The HF2LI is delivered with a fully featured graphical user interface and a choice of programming interfaces that greatly add to the usability of the instrument.
-
product
Electrosurgical Analyzer
HF-400
HF-surgery tester for functional testing of HF surgical devices according to IEC 60601-2-2.
-
product
PID Controller
Liquid Instruments' new instrument features real-time frequency-domain conDesign your control system's frequency response using the interactive Bode plotBlock diagram view of the digital signal processing with built-in probe points for signal monitoring2 input channels, 2 output channels with control matrix for blending inputsIncludes single or double integrators and differentiators with low- and high-frequency gain saturationtrol system design capabilities.
-
product
Pyroshock Testing
The purpose of Pyroshock (pyrotechnic shock) testing is to simulate the high-frequency, high-magnitude shock pulse experienced by an explosive event (such as an impact on a military tank or an explosive deployment charge). Pyroshock testing can expose failures in electronic components that are sensitive to high-frequency pyroshock energy. Common failures include: relay and crystal oscillator chatter, detachment of larger components from the circuit board, hard failures of small circuit components, and the dislodging of contaminants, which cause short circuits. Severe damage to crucial components used in space or in the military can produce critical results, such as loss of life, due to malfunction.
-
product
SF6 Decomposition Products Detector
JH4000A-4
Xiamen Jiahua Electrical Technology Co.,Ltd
JH4000A-4 SF6 Electrical Equipment Decomposition Products Detector is a high precision, intelligent and portable device, able to make judgment rapidly and correctly based on the content of main decomposition products of insulation materials inside the SF6 electrical equipment like SF6 circuit breaker, instrument transformer, GIS and transformer. It detects SO2+SOF2, H2S, CO and HF. It is reliable, accurate and stable. Inspected by authorities such as the National Institute of Metrology, the device, having excellent performance, complies with relevant international and national standards. It is a product recommended for use by the State Power Grid Company. Decomposition products detection provides reliable evidence for the internal fault diagnosis and it is an effective measure for preventive and corrective maintenance.
-
product
Adjustable High Frequency Reference Ballast
HCS-109A
HCS-109A Adjustable High Frequency Reference Ballast also called High Frequency Current Source. Comparing to IEC Test Method, HCS-109A is an Equivalent Test Method which is economic solution. HCS-109A equipped with Spectrophotometer & Integrating Sphere Test System. It can also measure the photo, color and electricity parameters for high frequency fluorescent lamp.Specifications: • Input voltage: 200V~240V, 50/60Hz • Input Power: 80 W max • Output Current: 130mA~400mA (Adjustable), accuracy: +/- 1% • Output Frequency: 25kHz< +/-2.0% (Adjustable), accuracy: +/- 0.3kHz • Output current total harmonic wave distortion: THD<2.5% (HF current wave)
-
product
AC Current Probe 1 mV/A, 6,000A, 0.055 Hz LF Bandwidth, 6.5MHz HF Bandwidth, 4m cable, 300mm coil
T3RC6000-LF
AC Current Probe 1 mV/A, 6,000A, 0.055 Hz LF Bandwidth, 6.5MHz HF Bandwidth, 4m cable, 300mm coil.
-
product
High-Frequency Signal Relays
Panasonic Industrial Devices Sales Company of America
Panasonic offers a variety of Signal Relays that can switch high-frequency signals. These products are ideal for applications including radio frequency switching, test and measurement, communication and more.
-
product
MOSFETs For High Frequency Amplifier
The MOSFETs shown below are best suited for amplification of high-frequency signals.
-
product
200 MS/s Waveform Generator & Dual 50 MHz Pulse/ Timing Generator
3172
The Racal Instruments™ 3172, a 200 MS/s Waveform Generator and Dual 50 MHz Pulse and Timing Generator, combines multi-instrument density and highfrequency performance in a single-slot, C-sized VXIbus format.Waveform output in the range of 100 μHz to 30 MHz with 16-bit vertical resolution (12-bit vertical for 3171 emulation) and pulse output to 50 MHz make the 3172 a powerful solution to a variety of test stimulus requirements.
-
product
Resistive Components
Diamond is the best thermal conductor on earth. Combined with a low dielectric constant, it is an excellent RF dielectric material for high-frequency applications in which thermal performance is equally critical. By applying cutting-edge thin film process and extensive millimeter wave design experience, Smiths Interconnect has created a high-performance line of resistive components. The resulting products, our Diamond RF Resistives® resistors, terminations, and attenuators, are significantly reduced in size and unparalleled in average and peak power handling.
-
product
Antenna Tuner HF+6m
DU 800 T
The DU 800 T optimizes the performance of your antenna and transmitter or SWL receiver by providing adjustable impedance matching. The DU 800 T also measures the Power and Standing Wave Ratio (SWR), which allows you to tune the indiceted SWR to the lowestpossible ratio for the selected transmit frequency.
-
product
SAM Line
PVA TePla Analytical Systems GmbH
The SAM Line offers easy-to-use scanning acoustic microscopes for process control and quality assurance as well as for research applications. The individual models are derived from a component platform that complies with industry standards and incorporates cutting-edge production and manufacturing technologies. Thanks to their new high-frequency and transducer technology, our acoustic microscopes enable detailed acoustic analysis in the ultrasound range up to 400 MHz.
-
product
Microtester Test Systems
With the micro probes and the fine-pitch adapters used on them, you are able to contact the finest test structures. E-tests, functional tests, IC tests or high-current tests are made to be affordable, efficient and with a short cycle time. With the integration of HF adapters we also enable the double-sided testing of HF substrates up to high frequency ranges.
-
product
LXI Microwave Multiplexer, 50Ω 36-Channel 1-Bank 4GHz BNC
60-891-001-002
The multiplexer has an extremely high level of performance with low VSWR, very high isolation, low loss and high power handling. It is ideal for switching 50Ω systems for HF up to microwave frequencies. It occupies 2U of rack space, providing a compact switching solution.
-
product
Bidirectional AC Source / Sink With Regenerative Power Supply
EAC-4Q-KS
*Single system from 15 kVA to 90 kVA and in parallel up to 500 kVA*Seamless transition between source and sink mode*Output: AC, DC, AC + DC*Output up to 2000 Hz (-HF option)*Add single-phase output (option -1P)*Up to 750 V LN output*Modular construction
-
product
Passive Probe, 10:1, 75 MHz, 2-Pack
N2142A
The Keysight N2142A is an extremely low-cost passive probe that provides a switchable 10:1 / 1:1 attenuation and up to 75 MHz bandwidth. It features a high input resistance of 10 MΩ (switchable to 1 MΩ) to address a wide range of measurement needs with low probe loading. The probe can be adjusted for both low-frequency compensation and high-frequency compensation. For the best measurements, you should compensate your probe to match its characteristics to the oscilloscope. This probe is compatible with Keysight InfiniiVision Series oscilloscopes with 1 MΩ input.
-
product
Passive Probe, 10:1, 200 MHz, 2-Pack
N2140A
The Keysight N2140A is an extremely low-cost passive probe that provides a switchable 10:1 / 1:1 attenuation and up to 200 MHz bandwidth. It features a high input resistance of 10 MΩ (switchable to 1 MΩ) to address a wide range of measurement needs with low probe loading. The probe can be adjusted for both low-frequency compensation and high-frequency compensation. For the best measurements, you should compensate your probe to match its characteristics to the oscilloscope. This probe is compatible with Keysight InfiniiVision Series oscilloscopes with 1 MΩ input.
-
product
Carbon/Sulfur Analyzer
EMIA-Step
In addition to the “EMIA-Expert/Pro” series of high-frequency induction furnace type, the “EMIA-Step” of tubular electric resistance heating furnace type has been newly added to our Carbon/Sulfur Analyzers lineup. It realizes highly accurate and sensitive analysis, and its variable heating temperature function enables the quantitative analysis by separating it by temperature and condition as well as whole quantity analysis.
-
product
Near Field Probes
Used for accompanying measurements of high-frequency, electric and magnetic RF fields on assemblies and devices.
-
product
Test Contactor/Probe Head
cBoa
cBoa™ test contactors and probe heads are the solutions for contacting high-frequency devices for package test or final test at wafer. The robust design and materials of the cBoa probe withstand the rigors of high-volume test by providing longer life and higher yield. The homogeneous DUT side plunger provides longer run times between cleaning and increased probe life.The cBoa features a stainless-steel spring for tri-temp testing and performs in operating temperatures of -55°C to +155°C and bandwidth of up to 35 GHz @ -1 dB.
-
product
Receiver And Exciter
MS 2010
Receiver Exciter is used to receive and transmit HF range signals & processing HF signals into voice and data format using DSP technology. It consists of high quality HF receiver and HF exciter. System has SELCAL and secure communication features. System has configuration facility for Frequency range, mode of operation (AM, LSB, USB, DATA, CW), volume, squelch level from external control unit. The exciter produces the low power signal which is fed to the power amplifier unit.
-
product
Terahertz (THz) Lasers From 0.89 To 2.52 THz
Insight Product Company offers terahertz lasers at frequencies from 0.89 to 2.52 THz. Output power is from 1 mW to 15 mW. Diameter of the output wave beam is ~ 40 mm. Typical sizes is 1.2x0.3x0.4 m. Transformer from quasi-optical output to the standard wave guides can be provided. The energy pumping is provided either by DC discharge or HF discharge.
-
product
Medical Ultrasound
Piezo elements form an essential component in medical diagnostics. Medical Ultrasound uses high-frequency sound waves to look at organs and structures inside the body. Medical professionals use medical ultrasound to view internal organs and during pregnancy to view the fetus. CTS provides both monolithic and composite piezoelectric elements used in medical ultrasound applications.
-
product
In-line Wet Process Concentration Monitoring
CI’s family of wet process concentration analyzers (WetSpec line) offers cost effective solutions for in-line wet chemistry monitoring. These products range from conductivity and NDIR solutions for simple chemistries concentration measurement, to spectroscopic systems for measuring multiple constituents and residues in complex solutions. The main concentration monitoring application that are served by CI Semi’s products are cleaning (SC1, SC2…) etching (HF, BOE, MAI….) and photo resist strippers (EKC, ACT, Piranha….).
-
product
RF Filters
Amphenol Procom has 40 years of experience in developing and producing high quality RF Low- and high-power Filters for professional radio systems, widely used in the Public Safety and Mission Critical radio TETRA networks in Europe. The comprehensive portfolio of Filter products from Amphenol Procom are designed by experienced engineers, and highly used in the HF-, VHF- and UHF radio frequency range.
-
product
Chip-Type Attenuators
Panasonic Industrial Devices Sales Company of America
Chip-Type Attenuators for high-frequency signal attenuation, level adjustment or matching improvement.
-
product
Rotatable Directional HF Antennas
Kratos Defense & Security Solutions, Inc.
Kratos’ horizontally polarized rotatable log-periodic antennas are constructed with wire radiators supported by a strong and unusually lightweight support structure.
-
product
Double Function Tester with Shielded HF Test Chambers
End-of-line Tester UTP 9010 RF
The UTP Series 9010 is a scalable test series available in a variety of feature-rich variants and many designs. The UTP 9010 RF function tester shown here as an example is suitable for tests with a medium number of channels and complexity. It is designed for parallel testing of two or more test items. The measuring instruments used are used alternately for several test items. Due to its compact design and construction as a modular system, this powerful tester can easily be expanded to larger numbers of channels.The integrated HF test chamber UTP 5070 developed by NOFFZ allows an independent shielded test. It can be operated manually or fully automatically by a robot .The basic version of the UTP 9010 series is an ideal system for functional and end-of-line tests and is already preconfigured for this purpose. The RF tester presented in the example is used in particular to test infotainment and eCall modules in the vehicle as well as IoT products with wireless technologies.
-
product
SWR / Power Meters
SX240C
Dimensions:170Wx115Hx150DmmWeight:1350gFrequency range:S1 (1.8-54MHz) S2 (140-470MHz)Power display rating:30W/300W/3kW(HF band only)Accuracy of full scale:±10%(F.S.)
