Filter Results By:
Products
Applications
Manufacturers
Interferometers
Combine waves to reveal their properties by measuring the pattern of interference.
See Also: Beam Splitters
-
product
Differential Interferometer
10715A
The Keysight 10715A Differential Interferometer performs differential measurements between the supplied reference mirror and a measurement plane mirror. It provides exceptional long term stability. The 10715A minimizes dead path, and, because the entire optical path through the interferometer is common mode, it eliminates thermal drift in measurements. The resolution of the measurement is twice that of a linear or single-beam interferometer.
-
product
Laser Head
5517DL
The Keysight 5517DL is used primarily in VME and PC based laser interferometer systems where the velocity of motion is faster, such as semiconductor lithography and flat panel applications. Please contact Keysight for custom requirements.
-
product
10G DPSK Demodulator
Optoplex’s Optical DPSK Demodulator, also known as Delay Line Interferometer (DLI), converts phase modulation to amplitude modulation over the entire C+L band in support of data transmission rates of 2.5,10 or 40 Gb/s. The DPSK demodulator is designed for phase modulated optical communication systemsutilized in commercial, defense and space exploration markets. The device plays a key role in improvingsignal quality and performance to meet the expanding demand for higher data rates and more complextransmission formats within current and next generation systems without major capital expenditure.Optoplex’s DPSK Demodulator is based on a patented free-space optical design, which is compact, athermal and polarization-independent. The measured frequency drift over temperature is only ~0.02 GHz/°C for our standard passive device. Further, this DPSK Demodulator exhibits a total polarization-dependent phase shift of less than 2 degrees over the entire operating temperature range with a high extinction ratio. Optoplex’s DPSK Demodulators can be configured to be fully tunable, colorless tunable or purely passive. Dual-Rate DPSK Demodulator is also available.
-
product
Interferometers
Sumix interferometers are designed for inspection of fiber optic ferrules, patch cords, pigtails and bare fiber in the process of polishing and assembly. They enable you to check polishing quality, test connector end face geometry per IEC, Telcordia or your own custom standards and generate reports to supply with your patch cords.
-
product
Interferometers
S-Series
Converge faster, polish surfaces 5X further from final formCorrect at the right spot with >10X lower image distortionControl 6X finer mid–spatial frequenciesRobust vibration tolerant and vibration insensitive data acquisitionFast, 6 seconds from measurement–to–custom report
-
product
Angular Optics Kit
55281A
The Keysight 55281A Angular Optics Kit adds pitch and yaw measurement capability to the 5530 Laser Calibration System. Ideal for use in precision calibration applications, it includes the 10770A Angular Interferometer and the 10771A Angular Reflector. Together the high-accuracy plane mirror interferometer and the angular reflector measure pitch and yaw motions along each axis that a machine tool or measuring machine travels. Results are displayed directly in arc-seconds or in mm/mm (in/in).
-
product
Inside Dimension (ID) Measuring Instruments
Pratt & Whitney Measurement Systems, Inc.
High accuracy is maintained by its laser interferometer, zero Abbe offset design, and large measuring table with swivel, center, tilt, and elevation control knobs.
-
product
Fourier Transform Optical Spectrum Analyzer, 600 - 1700 nm
OSA202C
Thorlabs' Optical Spectrum Analyzers (OSAs) perform highly accurate spectral measurements. Compatible with fiber-coupled and free-space light sources, these compact benchtop instruments suit a wide variety of applications, such as analyzing the spectrum of a telecom signal, resolving the Fabry-Perot modes of a gain chip, and identifying gas absorption lines. Many commonly available OSAs use grating-based monochromators, which have slow acquisition times due to the need to mechanically scan the grating and average out noise at each wavelength. Thorlabs' OSAs acquire the spectrum via a Fourier transform using a scanning Michelson interferometer in a push/pull configuration. This approach dramatically improves the acquisition time, enables a high-precision wavelength meter mode with 7 significant figures and ±1 part-per-million accuracy, and allows the included software to provide robust statistical analysis of the acquired spectra, as explained in the Design tab.
-
product
Fixed Magnification Interferometer
FiBO 250
FiBO 250 offers a solid and economical solution to automated fiber testing by bringing together full 2D visual inspection capabilities and true phase-shifting interferometry to achieve exceptionally accurate measurements. A fixed focal length 10x magnifier ensures maximum system stability and a very high level of repeatability.
-
product
Wavelength Meter
HighFinesse/Ångstrom offers sensitive and compact wavelength meters with a large spectral range for high speed measurement of lasers. The optical unit consists of temperature-controlled Fizeau-based interferometers that are read out by photodiode arrays. The high absolute accuracy is achieved by use of solid state, non-moving optics.
-
product
Adjustable Mount
10710B
The Keysight 10710B adjustable optics mount makes alignment faster and easier. It is a convenient accessory for the Keysight 10700A and 10701A beam splitters, the 10705A interferometer, and the 10707A beam bender. It allows for 8 degrees tilt and yaw adjustments.
-
product
Laser Head
5517CL
The Keysight 5517CL is used primarily in VME and PC based laser interferometer systems where the velocity of motion is faster, such as semiconductor lithography and flat panel applications. Option 009 allows a larger angular range of measurement by providing a 9 mm beam diameter for use with three-axis interferometers. Please contact Keysight for custom requirements.
-
product
1/4-Inch Cube Corner
10713D
The Keysight 10713D is one component of a family of measurement optics that tailor interferometer systems for the physical layout and measurement requirements of individual applications. Configured with appropriate laser head and system electronics, the optics are part of a precise positioning system that improves product quality, increases yields, and facilitates manufacture of precision products.
-
product
Precision Optics and Assemblies
For more than 35 years, Keysight has been designing and fabricating leading-edge optics for use in our laser interferometer systems. You can take advantage of this engineering, component fabrication, and assembly expertise and our state-of-the-art optics manufacturing facility in Santa Clara, California to deliver cutting-edge optical solutions to your customers:
-
product
Machine Calibration and Optimisation
Renishaw's laser interferometer and ballbar measurement systems assess, monitor and improve the static and dynamic performance of machine tools, co-ordinate measuring machines (CMMs) and other position-critical motion systems.
-
product
Regeneration Station
This equipment is a stand-alone device that enables to coherently regenerate an optical signal allowing long-haul dissemination of an ultra-stable optical frequency reference. Its architecture is based on the heterodyne phase-locking of a narrow spectral width laser diode on the reference signal. The station is equipped with low phase noise optical interferometer that perform a thorough characterization of the phase noise accumulated by the incoming signal, and a compensation system of this phase noise.
-
product
Short Range Straightness Optics
10774A
The Keysight 10774A Short Range Straighness Optics combines a straightness interferometer and reflector to make measurements over a range of travel up to 3 m (10 ft). The optics form a highly-accurate optical straightedge that can measure the straightness of travel of machine-tool and measuring-machine coordinate motions with a resolution of 0.04 micrometer (1 uin).
-
product
Fizeau Interferometers
Fizeau interferometers offer an unmatched combination of performance, quality and value in optical metrology. They produce accurate, repeatable interferometric measurements of surface shape, radius of curvature and transmitted wavefront quality.
-
product
Retroreflector
10704A
The Keysight 10704A retroreflector (cube corner) is a measurement reflector for single-beam measurements. It is paired with the Keysight 10705A single beam interferometer and is designed for making limited space, single-axis measurements. If mass is critical, the Keysight 10704A is available without housing as the Keysight 10713C, and for extremely critical mass requirements, the Keysight 10713D 1/4-inch base retroreflector can be used.
-
product
spectrometers
VERTEX 80/80v
The VERTEX 80 and the VERTEX 80v vacuum FT-IR spectrometers are based on the actively aligned UltraScan™ interferometer, which provides PEAK spectral resolution. The precise linear air bearing scanner and PEAK quality optics guarantees the ultimate sensitivity and stability. The VERTEX 80v is an evacuated optics bench that can eliminate atmospheric moisture absorptions for ultimate sensitivity and stability; enabling demanding experiments such as high resolution, ultra fast rapidscan, step-scan, or UV spectral range measurements.
-
product
Laser Interferometer Position Measurement Systems
When built into manufacturing and inspection equipment, a laser interferometer system reports the position or controls the motion of a product platform with more accuracy than any other method. It allows manufacturers to produce precision products from integrated circuits to medical devices to aerospace components that meet the most stringent specifications.
-
product
2x4 QPSK Mixer
Optoplex's 2X4 polarization diversified optical hybrid (aka QPSK Mixer) is a 2x4 device, which mixes an incoming signal with a local oscillator. The 4 outputs of this device are connected to 4 single-ended detectors (see the function diagram below). The device features a monolithic optical core integrating a PBS with an interferometer which is also widely used in Optoplex's interleaver and DPSK-demodulator platforms. This device is athermal, colorless, data-rate independent, compact in size and designed for manufacturability. This platform can also be extended to a 2X8 polarization diversified hybrid to incorporate with 4 pairs of balanced detectors.
-
-
product
Infrared Interferometers
Optical imaging applications are broad and varied. Testing at a system's design wavelength is critical for development, final alignment and qualification.
-
product
Laser Head
5517B
The Keysight 5517B is used primarily in VME and PC based laser interferometer systems where the velocity of motion is slower, such as machine tool applications. Please contact Keysight for custom requirements.
-
product
Retroreflector
10767A
The Keysight 10767A Linear Retroreflector is one component in a family of measurement optics that tailor interferometer systems for the physical layout and measurement requirements of each application. When configured with appropriate Keysight5530 Laser Calibration System components, 10767A becomes part of a precise positioning system that improves product quality, increases yields, and facilitates the manufacture of precision products.
-
product
Photonic Doppler Velocimetry (PDV)
Photonic Doppler velocimetry (PDV) is an established technique used to measure high-velocity events up to tens of km/s. It is also known as heterodyne velocimetry and can be used as a supplementary tool or replacement for Velocity Interferometer System for Any Reflector (VISAR).
-
product
High-Resolution Interferometer
10716A
The Keysight 10716A High Resolution Interferometer is used for single and multiple axis applications such as precision X-Y stages. The 10716A offers twice the resolution of conventional plane mirror interferometers and has the same excellent thermal stability as the 10706B High Stability Plane Mirror Interferometer. Measurement drift is typically of that exhibited by a conventional plane mirror interferometer. These features result in improved accuracy, repeatability, and thermal stability. However, slew rate is halved.
-
product
Interferometer
VFI-2000
The VFI is the interferometer of choice for industry leading photonics companies around the world. The VFI-2000 is an interferometric inspection system specifically designed for checking the surface quality and flatness of your cleaved or polished fibers. The VFI offers the perfect combination of a superb image quality with ease of use, and the reliability and robustness that our customers have come to expect from Arden products, resulting in fiber end face measurements that you can trust.
-
product
Displacement Measuring Interferometers (DMI)
ZMI Series
This unit measures retroreflector targets for tracking objects moving primarily in one linear dimension or rotating about a fixed point. ZYGO offers a standard and compact size linear interferometer to accommodate different system space constraints.
