Filter Results By:
Products
Applications
Manufacturers
Isolation
-
product
RS-232 Opto Isolation Module with DB9 Connectors
Model 9268
Ensure clean data transmission and reception between two devices by installing Telebyte Model 9268 Opto Isolation Module with DB9 Connectors. For applications ranging from testing laboratories to factory floors, isolation is a critical component in data communications environments.
-
product
Low-Profile 16-CH Isolated DI & 16-CH Isolated DO PCI Card
LPCI-7230
ADLINK LPCI-7230 is 32-CH isolated input and/or card. It provides a 2,500 C optical isolation protection. Two wide input range of the LPCI-7230 makes it easy to sense the status of external devices. The non-polarity characteristic is suitable for a wide variety of industry applications. The LPCI-7230 devices also feature a wide output range from 5 to 35 V, which is suitable for relay driving and industrial automations applications. The LPCI-7230 also provides two interrupt sources on digital input channels, which are easily user configurable.
-
product
temperature Measurement
Educated Design & Development, Inc.
Up to 8 resistance reading channels, 4-wire methodUp to 12 temperature reading chanels, use of Type K, 24 AWG, Teflon thermocouplesIn the Box:8 - data cable (Cat5e) to connect the isolation modules to the Resistance Reading Channels8 - Isolation Module connected between the HOT-30 and EUT (Equipment Under Test) to isolate high voltage8 - Banana Jack Sets (2 red, 2 black), to replace Kelvin Leads in tight places8 - Kelvin Probe Set12 - 72 inch K Type Thermocouple1 - USB2.0 Type A (standard) to Type B USB cable
-
product
Defect Isolation
*Traverse through the physical design to trace nets and vias down to the defect location*Utilizes industry standard LEF/DEF design files, scan-based test information, tester fail logs and diagnostic reports to determine and isolate the physical defect location*Enables the user to leverage their diagnostic experience to determine the root cause of the defect*Interactive layout viewer displays scan chains, mapped mismatches of scan cells, layers, nets and subnets with search capabilities(component, net, cell)*Physical XY coordinates are always displayed for components and nets to guide the user through the design to quickly identify suspect sites for FA using techniques like Emission, OBIRCH, LIVA, TIVA, or FIB
-
product
Digital Isolators
Silicon Labs' CMOS digital isolator products enable lower cost, smaller size, higher performance, lower power, and more reliable isolated circuits than competing optocoupler solutions. The Si80xx, Si83xx, Si86xx, Si87xx, and Si88xx families of one to six-channel bi- and unidirectional digital isolators support isolation voltage ratings up to 5 kV. With a broad product portfolio, a proven track record of industry innovation and an unwavering commitment to engineering excellence Silicon Labs isolation technology is ready to meet your isolation needs.
-
product
PXI 5A Mux 8-Bank 5-Ch Isolated COM
40-651-014
This range of high density power multiplexer modules is suitable for switching inductive/capacitive loads up to 5A at 250VAC. It is available in the following 1-pole multiplexer formats: 1-bank 48-channel. 2-bank 24-channel. 4-bank 11-channel. 8-bank 5-channel.Connections are made via a front panel 50-way male D-type connector. Power multiplexer modules are intended for switching heavy AC or DC loads or for slaving up to large external relays, contactors and solenoids.
-
product
Variable Height Workstations
2000 Series
The 2000 Series Vibration Isolation Workstation provides up to 12″ of tabletop height adjustment providing for improved user posture and comfort. This unit is ideal for applications where long hours at the workstation, or multiple shift use requires comfort adjustments.
-
product
PXI-4071, 7½-Digit, ±1,000 V, Onboard 1.8 MS/s Isolated Digitizer, PXI Digital Multimeter
778271-01
7½-Digit, ±1,000 V, Onboard 1.8 MS/s Isolated Digitizer, PXI Digital Multimeter - The PXI‑4071 is a high-performance 7½‑digit, 1,000 V DMM that provides the measurement capabilities found in two common test instruments: a high-resolution DMM and a digitizer. As a DMM, the PXI‑4071 delivers fast, accurate AC/DC voltage, AC/DC current, 2‑ or 4‑wire resistance, and frequency/period measurements, as well as diode tests. In the high-voltage, isolated digitizer mode, the PXI‑4071 can acquire waveforms at sample rates up to 1.8 MS/s.
-
product
PXI 5A Power Multiplexer, 1-Bank, 48-Channel, Isolated Common
40-651A-011
The 40-651A-011 is part of our range of high density power multiplexer modules is suitable for switching inductive/capacitive loads up to 5A at 250VAC. It is available in the following 1-pole multiplexer formats.
-
product
Rectal Probe For Rats
RET-2
• Smooth ball tip. Stainless steel shaft - 1'' long, .059'' diameter. Tip diameter .125'', 5 foot lead length. Time constant 0.8 seconds. Not Isolated
-
product
300W to 504W - Single Output
iQG Series
*Standard Quarter Brick Footprint*36-76 Vdc Inputs*9.6, 12 Vdc Outputs*1500 Vdc Isolation*Baseplate Cooled*94.5% Typical Efficiency*Droop Load Share Option
-
product
Rectal Probe For Mice
RET-3
• Smooth ball tip. Stainless steel shaft - 3/4'' long, .028'' diameter. Tip diameter .065'', 5 foot lead length. Time constant 0.5 seconds. Not Isolated
-
product
Isolated Digital Input/Output Card
PCI-IDIO-16
The PCI-IDIO-16 is a low-cost, 6.8" card that provides isolated input and output for PCI-bus computers. The card has sixteen optically-isolated digital inputs for AC or DC control signals and sixteen isolated FET outputs. For safety reasons in working with AC voltages, insulating shields are provided with each card.
-
product
Midi Logger
GLT400
*Transferring data to PLC via Modbus/TCP protocol*DC Power only for -20 to +60 operation*Supports WEB server, FTP server and FTP client network functions for remote monitoring and controlling*High Isolation inputs to ensure signals are not corrupted by noise from other channels*Connect as a remote terminal unit of GL840
-
product
75 High Isolation LXI RF Multiplexer
Pickering's LXI high isolation RF multiplexers are suitable for switching 75 signals up to 1GHz - ideal for constructing complex microwave switching systems for many applications.
-
product
UHF/RFID Power Divider Combiner 4-Way, TNC Female, 350-1000 MHz, 30 Watts
PD2941
INSTOCK Wireless Components, Inc
UHF/RFID Frequency (350 - 1000 MHz)Low Insertion Loss (0.4 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.10 : 1 avg)RoHS Compliant Splitter ConstructionTri Alloy TNC Female (Jack) 50 Ohm
-
product
Multi Channel Linear Vibration Motor Current Isolation tester
BK2017
The BK2017 Current and Isolation Tester was designed as a single purpose machine for quickly testing up to 8 linear vibration motors at a time. You can test current and isolation without checking other characteristics of the motor. With its simple design, it is very easy to use and the results appear clearly on the screen in about half a second. And with only 2 cables to connect, it can quickly be plugged into an automatic loader/sorter for even faster results!
-
product
Partial-discharge Detection System
GDYT Series
GDYT series include partial discharge power frequency testing transformer(YDTW),partial discharge detector(GDJF2008),Isolation filter frequency doubling power device(GDSF-81G) and power frequency withstand voltage control table(GDYD table).It widely used in electrical manufacturing,power operation departments, research institutes and universities.
-
product
HBM Verification Tester
HBM-VT
High Power Pulse Instruments GmbH
- HBM pulse generator verification tester according ANSI/ESDA/JEDEC JS-001 up to ±10kV- To be used in HBM test and qualification labs for regular pulse generator specification compliance test in order to fulfill lab audit and certification requirements- Fully automatic compliance test and verification of HBM pulse generators regarding ANSI/ESDA/JEDEC JS-001 normative standard at 3 different load conditions: Short Circuit, 500 Ω, and a reference diode at VBR=15 V reverse breakdown voltage, including DC test- Parameter evaluation and verification of the transient HBM current waveforms: Peak Current, Rise Time, Decay Time, Maximum Ringing Current- Optionally available upgrade for all HPPI TLP-3010C, 4010C, 8010A, 8010C, HBM-TS10-A hardware systems in combination with HBM-S1-B (6kV) pulse generators (upgrade on request)- Fully automatic test report generation (PDF)- Electrically floating (no fixed system ground): The HBM loads, current sensor output, USB control interface and the enclosure are electrically floating. There is no limiting system ground which may introduce common-mode interference induced HBM current measurement errors.- Isolated industrial full-speed USB control interface- Isolated power supply derived from USB port- Compact size 126mm x 82.5mm x 44.5mm
-
product
Contact Resistance Meter
CRM 100C
CRM 100C directly measures resistance values with DC current injection under live switchyard conditions.The CRM 100C is specially designed to reliably measure contact resistance of Circuit Breakers, Isolators, Bus Bar joints, welded joints etc., under the hostile electrostatic noise found in live EHV switchyards. It can also be used for testing cables, graphite bars etc.
-
product
32 Channel Optically Isolated Digital Card
104-IDIO-16 Family
The Model 104-IDIO-16 is a 32-channel PC/104 utility board featuring 16 optically isolated inputs and 16 optically isolated solid state outputs. The isolated, non polarized inputs may be driven by either DC sources of 3-31V (or higher by special order) or AC sources at frequencies of 40Hz to 10KHz. Optically isolating the digital inputs from each other, and from the computer, assures smooth, error-free data transmission in noisy, real-world environments. The 16 input channels are available via a 34-pin IDC type header. The fully protected solid state outputs, capable of sourcing 2A each, are inherently more reliable than electromechanical relays and give system architects a more robust product to design with. The solid state outputs are available via a 50 pin IDC type header.
-
product
High Voltage Isolator for Logic Analyzers
LX-08
The LX-08 series of high voltage logic analyzer adapters provides a safe isolated method of measuring high voltage control signals with a low voltage logic analyzer. All inbound signals are optically isolated and attenuated to a safe level for the delicate inputs typically found on logic analyzers. The inputs on the LX-08 are capable of withstanding voltages up to +/- 300V AC/DC, higher voltage configurations are available upon request. Rather than probing with multiple neon screwdrivers, the LX-08 can provide simultaneous viewing of up to 8 circuits in the STANDALONE mode via the indicator array. Need to catch a transient event or map out a timing sequence? Just add a logic analyzer to the outputs of the LX-08 and turn it into a high voltage logic analyzer. High voltage signals that were hazardous for a logic analyzer can now be measured safely. Typical outputs of a high speed PLC sequencer can be precisely timed and measured from both sides of the control relay. With the built in user selectable AC filter circuit, an AC signal can be measured as DC events or AC cycles.
-
product
Isolated SCIM5B Analog Signal Conditioning Products
SCIM5B
BEE INSTRUMENTS offers cost- effective, isolated industrial signalconditioning modules. The SCIM5B analog modules are form, fit, and functional equivalents to similar products from other manufacturers. The product range includes a complete selection of backpanels, interface cables, racks, fuses, jumpers, power supplies, and other accessories.
-
product
Isolated Input Relay Card With COS
PCIe-IIRO-16
This product is a x1 lane PCIe isolated digital input and relay output board with Change of State (COS) detection capabilities.
-
product
16-bit, 200KHz, 16 Isolated Differential Analog Input Board, 8 Isolated 24V Digital I/O
APCI-3002
Analog input board, 16-bit resolution, 16 differential inputs with 200 kHz sampling rate.
-
product
Isolated Serial Communication Card
PCI-ICM-1S
The PCI-ICM-1S is a single port asynchronous optically isolated serial communication card that can be installed in any 3.3V or 5V PCI slot computer. Data lines are opto-isolated from the computer and from each other to assure communication even when large common mode voltages and noise are imposed.
-
product
RF Test Enclosure With Preconfigured I/O Panels, ≥ 90 dB Isolation, 300 MHz - 18 GHz
dbSAFE X
The dbSAFEx Series advanced shielded boxes are versatile for any wireless testing. Designed to operate between 300 MHz to 18 GHz, testing of wireless devices has never been more reliable and affordable.
-
product
High Voltage Isolation Test Systems
HT 9460 and 9464
Accurate and non-destructive production testing of ac Isolation Voltage and Partial Discharge. With over 450 systems installed worldwide the 946X series of test systems are the standard and system of choice used by the majority of semiconductor manufacturers that produce optically isolated devices.
-
product
PXI-8432/ 4-Port, Isolated, RS232 PXI Serial Interface Module
779538-01
4-Port, Isolated, RS232 PXI Serial Interface Module - The PXI‑8432/4 is a high-performance interface for high-speed, port‑to‑port isolated communication with RS232 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
product
RF Power Splitter, Combiner, Divider RoHS, 2 Way, Type-N Female, 698 - 2700 MHz, 50 Ohm
PD2020
INSTOCK Wireless Components, Inc
Wideband Frequency (698 - 2700 MHz)Low Insertion Loss (0.2 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.10 : 1 avg)RoHS Compliant Splitter ConstructionTri Alloy Type N Female (Jack) Low PIM
