Filter Results By:
Products
Applications
Manufacturers
-
product
FireBird Camera Link Frame Grabber (1xCLD-2PE4)
AS-FBD-1XCLD-2PE4
FireBird is designed for ultimate performance using Active Silicon’s proprietary DMA Engine technology, “ActiveDMA”. This technical innovation applies RISC based processor techniques and guarantees zero CPU intervention, high-speed and low-latency image data transfers.
-
product
High-Speed Digitizers
ADP7000 Series
Guzik AXIe ADP7000 Series High-Performance Digitizer and Digital Processor combine high-speed waveform digitizer with built-in digital signal processing, which both enable mixed-domain signal capture and analysis with high-speed data transfer links to computers. The ADP7000 Modules (ADP7084 and ADP7104) come in a display-less 2U high 19” AXIe modular form factor.
-
product
40Gb/s DPSK Receivers
Targeting for the next-generation 40Gb/s system based on advanced optical differential phase shift keying (DPSK) demodulation, Optoplex’s 40Gb/s Integrated DPSK Receiver (DPSK Rx) demodulates an incoming DPSK optical signal into a pair of differentially (amplitude) modulated RF outputs at data rate up to 43Gb/s in a compact package. Phase modulated optical signals offer much better dispersion performance compared with traditional amplitude modulated counterparts because the carrier light stays on all the time so that the intensity-dependent nonlinear effects in the transmission link are avoided, resulting in longer transmission distances.
-
product
Terminal Housing MID JTRS & MIDS LVT
TCG
Curtiss-Wright Defense Solutions
Provide a tactical edge to warfighters with a mobile, compact, and affordable terminal housing case equipped with the technology to meet Link 16 communication requirements and supply your program with a complete tactical data link solution.
-
product
STAR-Ultra PCIe
163
The STAR-Ultra PCIe is a SpaceFibre Multi-Lane interface and link analyser, designed to aid test and development of SpaceFibre equipment. It can transmit and receive SpaceFibre traffic from a host PC at data rates in excess of 10 Gbit/s, and it can record and display SpaceFibre traffic transmitted and received on one SpaceFibre port.
-
product
PXI 2A Multiplexer, 1-Bank, 128-Channel, 1-Pole
40-614C-015
This 1-bank, 128-channel, 1 pole version is part of the 40-614C High Density 2A multiplexer module range that is available in 20 configurations (see Also in this Range link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
product
RF-Antenna Communication Links Functional Test
The application encompasses functional tests of very large quantities of automotive antenna amplifiers, plus parallelization of tests by implementing several test stations in a rotary indexing table. The DUTs are inserted manually and after final assembly, they are loaded into the rotary table; this requires manual triggering by the operator.
-
product
Package Testing
Package testing helps manufacturers verify their package designs to ensure that their products will not experience damage during shipping. Products are often shipped across states, countries and continents to reach their destination. This is an unavoidable link in the supply chain and, as such, packaging must be designed to protect products during the shipping process.
-
product
PXI/PXIe High Density 2A Multiplexer, 4-Bank, 4-Channel, 8-Pole
42-614D-009
The 40-614D-009 (PXI) and 42-614D-009 (PXIe) 4-bank, 4-channel, 8-pole multiplexers are part of the High Density 2A multiplexer module range available in 23 configurations (see 'Also in this Range' link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
product
Fully Automatic Close Link Single Phase Energy Meter Test bench
SY8125
Hong Kong Songyang Industrial Ltd.
The devices are fully made by aluminum alloy materials and the table board is composed of fireproofing and heat-proof materials. ● The output voltage and current use soft startup and stop. It has the protection functions of voltage short circuit, current open circuit and power amplification exception.● The device has the features of high stability, good reliability and large output power. ● High level of autoimmunization. The coexistence of special small keyboard and PCs, convenience to use.
-
product
PXI 2A Multiplexer, 1-Bank, 16-Channel, 8-Pole
40-614C-018
This 1-bank, 16-channel, 8 pole version is part of the 40-614C High Density 2A multiplexer module range that is available in 20 configurations (see Also in this Range link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
product
PXI/PXIe High Density 2A Multiplexer, 4-Bank, 32-Channel, 1-Pole
40-614D-006
The 40-614D-006 (PXI) and 42-614D-006 (PXIe) 4-bank, 32-channel, 1-pole multiplexers are part of the High Density 2A multiplexer module range available in 22 configurations (see 'Also in this Range' link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
product
Cable, Power over Camera Link (PoCL), MDR to MDR, 5M
199744-05
26-Pin MDR/SDR Camera Cable - The PoCL Cable provides a Power over Camera Link (PoCL) cable assembly. This cable carries power as well as signal communication for PoCL applications between compatible cameras and frame grabbers. The PoCL Cable is available in 26-Pin Mini Delta Ribbon (MDR) male to 26-Pin MDR male, or 26-Pin MDR male to 26-Pin Shrunk Delta Ribbon (SDR) male variations.
-
product
PCI/cPCI-VME link/interface
SIS1100/3100
The SIS1100/SIS3100 PCI/cPCI to VME interface card combination was developed to meet the requirements of demanding VME data acquisition systems. The link is optimized for low latency high speed readout.
-
product
CL PX4 SE Frame Grabber
Xcelera-CL PX4 SE
The X64 Xcelera-CL PX4 SE is a highly versatile PCIe frame grabber capable for one Camera Link™ Base, Medium, or Full camera and performing image transfers at rates up to 1024MB/s. Its low cost, combined with its ability to support multiple tap configurations from area and linescan monochrome/RGB cameras simultaneously; in addition to its onboard FPGA Bayer decoding and real-time shading correction makes the X64 Xcelera-CL PX4 SE an ideal solution to a wide variety of cost-sensitive applications.
-
product
Pluggable Optical Line System
POLS
Use our compact pluggable modules to provide up to 8 DWDM channels to enable high-capacity optical inter-datacenter links for internet service and cloud hosting providers.
-
product
Dual Lock Link Kit
DAQA194A
The Keysight DAQA194A (5061-8769) dual lock link kit is recommended for side-by-side combinations and includes links for instruments of different depths. This kit can be used with the DAQA191A 2U Dual Flange Kit to mount two Keysight System II (half-width, 2U height - 88.1mm) instruments side-by-side.
-
product
Model MCPC: Lab Moisture Analyzer
AM-MCPC-RS
PC-Based lab/production moisture analyzer connects through RS-232 Serial Port. Designed for nuts, granules, powders, pellets, chips, or flakes. Includes two sample cups, MCPC-RS test chamber, windows PC-based software, and more. See product link for complete features and minimum computer requirements.
-
product
Vibration Analysis
The vibration analysis software WaveImage includes a full set of methods providing an accurate and detailed overview of your vibration measurement data. This gives you a clear understanding of the cause-and-effect relationships between specific excitations and their vibrational response. Create a simple geometry model of your structure and link your multi-channel measurement data to the points in the geometry where the data was recorded. Then visualize the dynamic deformation of the structure under specific operating conditions with a detailed animation.
-
product
LGA 1151 Intel® Xeon® E & 8th/9th Generation Core™ ATX Server Board with 4 DDR4, 7 PCIe, 6 USB 3.1, 8 SATA3, Quad/Dual LANs, IPMI
ASMB-786
- LGA 1151 Intel® Xeon® E & 8th/9th Generation Core™ i7/i5/i3 processors with C246 chipset- DDR4 2666/2400/2133 MHz ECC/Non-ECC UDIMM up to 128 GB- One Gen 3.0 PCIe x16 link (or two PCIe x16 slots with x8 link), two PCIe x4, and three PCIe x1 slots- Triple displays - DVI-D, VGA and HDMI 2.0 ports- Eight SATA3 ports and six USB 3.1 ports- Rackmount optimized placement with positive air flow design- 0 ~ 60° C ambient operating temperature range
-
product
Cable Continuity Tester, RS232, DB9 In Line Signal, Network, 21.01 mm, 35 mm, 45.01 mm
72-9265
The 72-9265 is an In-Line Signal Link Tester. Quickly test DB9 connections with this handy tester. No need to carry bulky, expensive cable testers to test only one or two cable types. Mini link tester fits easily in your pocket or tool box and requires no external power. Connects in-line and displays signal data connectivity on LED's per each conductor. Save time and money by diagnosing connectivity issues.
-
product
Temperature Controlled Microscope Stage
Linkham Scientific Instruments
Specialists in temperature controlled microscopy, Linkam Scientific Instruments, announce the launch of their Optical DSC450 which enables simultaneous visualization of thermal processes for improved materials characterisation. The Optical DSC450 enables the user to measure glass transitions and melting behaviour of a wide range of substances whilst accurately controlling temperature from -196 °C to 450 °C. The atmosphere of the stage can also be purged with gas as required by the user. A new feature which will increase the characterisation capabilities of the DSC system is to combine it with imaging capability. The new LINK Digital Imaging module enables additional information to be obtained by correlating optical changes such as colour with temperature. The new TASC analysis tool takes this further. TASC (Thermal Analysis by Surface Characterisation) is a new image analysis capability which enables structural changes in samples to be tracked and quantified optically. It has the unique ability to measure local transition temperatures allowing different points on a sample to be identified. The new DSC system is great tool to use in research and quality control to measure quantitative values for glass transitions, melting peaks and sample purity and, when combined with TASC, even sample homogeneity.
-
product
ARINC 664 Part 7 XMC Interface Module
XMC-664-V2
Avionics Interface Technologies
Supports IEEE 802.3 10/100/1000 Mbit/s Full-Duplex Ethernet links - Utilizes SFPs to support both copper and optical interfaces - Simulates multiple ARINC 664 End Systems - VL traffic shaping and input VL redundancy management - Supports up to 4K Output VLs and 4K Input VLs - Supports up to 16K Sampling & Queuing output message ports and up to 16K input Sampling & Queuing message ports - ARINC 653, UDP, IP protocols managed onboard - IRIG-B time code encoder/decoder - Automatic message sequencing & periodic data generated onboard - Error Injection including Runt Frames, Short IFG, and Invalid MAC FCSDevice driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
product
OmniTrak Solution
TSI OmniTrak™ Solution is a customizable, scalable, and affordable solution enabled by connecting innovative monitoring instruments, intelligent TSI Link™ software and service solutions. This platform solution of connected devices allows you to plan, measure, report, recommend, and monitor key business drivers and risks to help improve health, wellbeing, and efficiency.
-
product
PCI-8361, PCI Host, 100 MB/s, Copper Cable MXI-Express Device for PXI Remote Control
781394-01
The PCI‑8361 is an MXI‑Express remote controller for devices or systems over cabled PCI from a computer with a PCI slot. The PCI‑8361 card provides a PCI link over a copper cable to the PXI‑8360 remote control module when used for PXI system control. This link is transparent to software applications and drivers, so computers and servers can control connected devices with no additional programming. With NI remote controllers, PXI modules can be used as if they are PCI devices directly installed in the computer.
-
product
DVI Extender via Two Singlemode/Multimode Fiber Optic Cable up to 4,920 Feet
ST-2FODVI-LC
The XTENDEX® DVI Extender via Fiber Optic Cable locates a single link digital DVI display away from a computer up to 4,920 feet using singlemode fiber optic cable and 1,640 feet using multimode fiber optic cable. Supports resolutions to 1920x1200.
-
product
Tube Mount Transmitter / DIN Rail Receiver
The 28670XX-DRX Series are unidirectional wireless systems that comprise a transmitter and a receiver.This Drexelbrook transmitter accommodates two digital signals in the range from 5 to 30 V AC/DC or 100 to 240 V AC and one analog current signal (4-20 mA). These signals are available for further processing at the receiver in the form of two relay contacts and one 4-20 mA current output. In addition, a third relay in the receiver diagnoses the status of the wireless connection (RF link).
-
product
Multimedia Test Video Generator/Analyzer
882EA-DP
The Teledyne LeCroy quantumdata 882EA-DP test instrument with both a DisplayPort 1.1 transmitter and receiver (analyzer) option is packed with features for video and audio testing of DisplayPort monitors and sources at pixel rates up to 268 MHz. The 882EA-DP test instrument provides two (2) additional DisplayPort ports for passive monitoring of the link layer through the optional Aux Channel Analyzer (ACA) application. The ACA option enables you to monitor link training transactions either between the instruments Tx port or its Rx port with the DisplayPort device under test. The 882EA-DP instrument can optionally be equipped with industry approved compliance tests for Link Layer, EDID and HDCP 1.2.
-
product
Fiber Optics Test Data Management, Remote & Cloud Applications
Fiberizer™
Software solutions for remote optical testing and data post-processing for managing test data and generating reports that integrate OTDR, link map, GPS coordinates, OLTS (loss and ORL), connector inspection, and captured images. Available for Window PC, Mobile Apps (Android, iPhone and iPad devices) and Fiberizer Cloud.
-
product
Variable Fiber Optic Attenuator
Variable fiber optic attenuator could help simulate distance or actual attenuation in the fiber optic testing work by inserting a calibrated attenuation into the link. By using the variable fiber optic attenuator, technicians could verify the power margin received by testing the fiber optic link power budget. Variable fiber attenuator can help user vary the light power injected from a light source into the optical fiber. Important parameter of variable fiber attenuator include its insertion loss, reflection loss and attenuation range.
