Filter Results By:
Products
Applications
Manufacturers
-
product
High Temperature Diametral Extensometers (1000 C)
Model 3580
Jinan Testing Equipment IE Corporation
This model is for diametral strain measurement with furnace and induction heating systems. Quartz rods and water-cooling allow the unit to be used for high temperature testing of metals, ceramics and composites. With induction heating, this model often can be used without water-cooling. When used in furnaces, the extensometer is often mounted directly to the furnace side cut-out. Optional load frame mounting brackets are available for supporting the extensometer in cases where furnace mounting is not possible. These optional mounts are used with induction heating or furnace systems. The Model 3580 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
product
Analog Tensile Testing Machine
It can test materials like rubber, wood, plastic, rexins, teflon, cardboard, composites, ferrous metals, non-ferrous metals etc.Wide range of Grips, Attachments & Special fixtures are available to suit varieties of material and shapes. Continuous roll autographic Load Vs Elongation recorder.Continuous roll autographic Load Vs Elongation recorder.Elongation scale with least count 1 mm.Elongation scale with least count 1 mm.Three measuring ranges for accurate testing.Three measuring ranges for accurate testing.A number of straining speeds are available for proper selection.A number of straining speeds are available for proper selection. Machine with AC or DC drive motor is available.Machine with AC or DC drive motor is available.Various Models – Maximum Capacity from 200 N to 50 kN.Various Models – Maximum Capacity from 200 N to 50 kN.Loading accuracy well within ±1%Loading accuracy well within ±1%Hand operated cutting press with different sizes dies are available for cutting dumbbell specimen.Hand operated cutting press with different sizes dies are available for cutting dumbbell specimen.
-
product
ATR 3D Layout Machine
ATR Model is standrad layout machine for marking work and 3D measruing.
-
product
ESD & Latch-Up Test System
Identify and help correct ESD and latch-up susceptibility issues on sensitive integrated circuit components prior to full-scale production with the Thermo Scientific™ MK.2-SE ESD and Latch-Up Test System. The MK.2-SE test system provides advanced capabilities to test high pin count IC devices to Human Body Model (HBM) and Machine Model (MM) ESD standards. The system’s pulse delivery design addresses wave form hazards such as trailing pulse and pre-discharge voltage rise, and performs Latch-Up testing per the JEDEC EIA/JESD 78 Method.
-
product
Averaging Extensometers for ASTM D5656 Shear Tests
Model 4013
Jinan Testing Equipment IE Corporation
The Model 4013 extensometer meets the requirements of ASTM D5656 for measuring the strain properties of an adhesive in shear. It uses different contact point spacing compared to the extensometer shown in D5656. This makes it much easier to mount and eliminates the slippage problems associated with the design shown in the ASTM standard. The Model 4013 is available with all of Epsilon’s temperature configurations. It has a 3.0 mm (0.12 inches) full scale measuring range. The conical point contacts included with the extensometer are made from tungsten carbide.The Model 4013 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
product
Friction Player
FPR2200
The friction coefficient is measured by the pin-on-disk method. Also, by measuring the coefficient of dynamic friction, surface destruction occurs due to wear and changes in the coefficient of dynamic friction occur .This machine is the latest model that was created by realizing various measurement modes, improving data resolution, and pursuing ease of use based on the achievements cultivated in the friction and wear tester that we have manufactured and sold in the past.
-
product
Concrete Compression Flexure Tester
The Compression & Flexure testing product line from Qualitest offers a wide variety that will fit almost any budget. Different options between models include digital or analog display, single or dual range, and different types of configurations. All the Compression & flexural testing machines conform to international standards for compressive & flexural tests.
-
product
Universal Testing Machines - Tensile Tester
UTM
A Universal Testing Machine (UTM) is used to test both the tensile and compressive strength of materials. Universal Testing Machines are named as such because they can perform many different varieties of tests on an equally diverse range of materials, components, and structures. Most UTM models are modular, and can be adapted to fit the customer’s needs.
-
product
Machine Vision Camera - 1.6 MP, 78 FPS, Sony IMX273, Color
Blackfly S Board Level
The FLIR Blackfly Board Level variants are high performance, machine vision, area scan cameras designed for embedding into tight spaces. Unlike many board level cameras, it boasts a rich feature set applied to the latest CMOS sensors; the same feature set as the cased version. It is ready for integration with proven compatibility with popular SBCs and SOMs. The Blackfly S board level models enable OEMs to develop smaller, lighter, and lower cost solutions with embedded system connectivity and rich features.
-
product
Universal Hardness Tester
A great advantage for testing labs is combining different test methods in one Universal hardness tester, which allows significant cost and space savings, flexibility and user-friendliness. Qualitest offers a competitive range of dead-weight models up to best selling load-cell type systems. These Universal hardness testers can cover Rockwell Regular, Superficial as well as Brinell and Vickers scales in one single machine.
-
product
Spring Fatigue Testing Machine
TPJ Series
Jinan Testing Equipment IE Corporation
Model TPJ Series Mechanical Computer Control Spring Fatigue Testing Machine is mainly used for the fatigue properties of all kinds of coil springs, disc springs, shock absorbers, and seal springs etc. The Spring Fatigue Testing Machine consists of motor, reducer on the connecting cams to drive the connecting rod and make reciprocating motion achieve the compression fatigue movement. The Spring Fatigue Testing Machine is efficient without any pollution to the environment. Equipped with different accessories, the Spring Fatigue Testing Machine can test springs of different sizes. Adopting the single-chip machine control, the Spring Fatigue Testing Machine realizes auto stop function when it reaches the preset test times. The Spring Fatigue Testing System is widely used in quality controls for spring, shock absorber production, and relevant applications.
-
product
Triaxial Testing Machines
Triaxial testing machine for position-controlled triaxial tests with test cells 10-3150 ... Stand model in two-column design with electronic force transducer, flanged to the testing machine crosshead and adjustable electronic position transducer 50 mm. The machine is driven by a stepper motor with central spindle and pressure plate below.
-
product
Pendulum Impact Testers
Qualitest offers Charpy / Izod Impact Testers with capacities up to 750J meeting and exceeding ASTM E23, ISO, DIN, JIS, standard requirements. The key benefits of this line of top technology models are price competitiveness, extremely high precision and durability, automatic motorized lifting of the pendulum hammer to optimize cycle times, flexibility, efficiency for low/high temperature testing, and much more. Optionally we offer temperature chambers, automated sample handling, centering device, Charpy sample preparation and broaching machines for preparation of notched bar specimens.
-
product
Rugged, Long Gauge Length Extensometers
Model 3543
Jinan Testing Equipment IE Corporation
With over 15 years of proven reliability in the world’s most demanding testing environments, the Model 3543 extensometer is designed to survive in those applications where standard axial extensometers would not. Designed by Epsilon, the Model 3543 was created to survive specimen failure by separating into two halves, thus preventing permanent damage to the module body. During operation, the upper half of the extensometer pulls out of the main body. Tapered measuring beams activate strain gaged flexures within the unit. This unique design allows long measuring ranges, yet retains compatibility with electronics for strain gaged transducers. These models offer high accuracy and are light weight but rugged, with low operating force. They are tension only units.The units have hardened tool steel knife edges. Standard quick attach wires provided with the extensometer work on flat specimens up to 12 x 31 mm (0.5 x 1.25 inch) and on rounds up to 25 mm (1 inch) diameter. Optional quick attach kit wire forms are available for use on larger samples. See Model 3542L for long gauge lengths with smaller measuring ranges.The Model 3543 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
product
Scanners
TK94A/TK94RL
The two scanner variations of the type TK94 have similar features. The difference is that variation "A" is used for checking single positions or free space while the version "RL" rotates in both directions without stopping to check for two tools. These scanners are best suited for harsh environments and have a built-in air purge with a strong/fast motor. This scanner would be used in applications that previously used the BK Mikro model 4 or 5 scanners such as lathes, transfer machines or in the work envelope of machining centers.
-
product
Software / Downloads
Pratt & Whitney Measurement Systems, Inc.
Powerful and resourceful, Pratt & Whitney's GageCal Software sets a new standard for user-friendly calibration and part measuring. By controlling the operation and facilitating data collection, GageCal increases total measurement productivity. GageCal is included with the following product lines: Labmaster Universal Model 175, 1000M, 1000A, BM175, BM1000M, BM1000A, Labmicrometer Model 900, 1600, External Supermicrometer Model PC, Universal Supermicrometer Model 501, 504. GageCal is an optional add-on for the External Supermicrometer Model C and Digital Measuring Machines.
-
product
Production Test Stands for Electric Motors
Electric drives such as DC and EC motors are more and more extensively deployed in the automotive industry. At the same time there is an increasing requirement for a 100% analysis of motors for fault detection and error analysis as well as statistics on quality, without increasing production cycles times. The model-based Parameter Identification method (PI method) from imc allows testing to be performed under load, yet without an “explicit” separate load machine. Instead, the motor is loaded dynamically by exploiting its own inherent inertia. This allows motor parameters such as resistance, inductivity and friction to be determined within a few seconds. A mathematical model and its parameters reflect motor behaviour in its completeness and make it possible to monitor motor production based on limit values and trend statistics. The identified parameters of the model equation can then be used to calculate derived key performance indicators of the motor characteristic curve.
-
product
Manual Test Solution
Titan
Grund Technical Solutions, Inc.
Titan is an easy to use, low cost Human Body Model (HBM) or Machine Model (MM) manual test solution. It can be used for design, engineering, and characterization of your devices. Ranging from 50 V to 16,000 V the Titan will have the largest voltage range of any HBM tester.
-
product
Network Cable Tester
NCT-500
ShinewayTech NCT-500 Network Cable Tester，Functions ranging from ISO / OSI reference model physical layer, link layer, network layer multiple detection. One machine in hand, which can quickly locate network faults and determine the link quality.
-
product
Bi-Axial or Axial Averaging Extensometers
Model 3560
Jinan Testing Equipment IE Corporation
This extensometer is ideally suited for testing anisotropic materials such as advanced composites as well as for general purpose tests like determining Poisson’s ratio. The Model 3560BIA uses a design unique to Epsilon, where the knife edges remain parallel during the displacement. This approach greatly reduces crosstalk between axes and allows use on round or flat specimens with equal ease. These extensometers are very easy to mount. Integral springs hold the unit on the test sample. The parallel multiple flexure design makes these units very durable.The Model 3560AVG reads axial strain only as a single averaged output. It may also be supplied with two independent outputs, one measurement from each side of the specimen. This set-up is most commonly required when an indication of specimen bending is desired. The second version, the Model 3560BIA, includes both the averaged axial strain and the transverse strain. Again, this may also be configured as dual independent axial readings, which results in a three channel extensometer.The Model 3560 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
product
Digital Insulation Multimeter Tester 1 KV
MIRT-61
The Motwane Manufacturing Company
The MOTWANE multipurpose tester Model MIRT-61 is a Versatile, battery operated Digital insulation tester with true RMS industrial grade multimeter features best suited for industrial preventive maintenance. With test voltage range up to 1 KV , highest insulation resistance range of 6G Ohm and multi featured function of RMS multimeter (i.e. AC/DC 1000 V) ; makes it a superior offering for Industry and Service segment. It is designed predominantly for low voltage insulation resistance testing in maintenance and services, which involves the applications like Cables/Wires, Rotating Machines, LT transformers, Switchgears and Industrial installations. It is designed to suit the extreme environment conditions. Save your operating cost and test more with this single box design rather buying two different products.
-
product
Open Source Computer Vision & Machine Learning Software Library
OpenCV
Open Source Computer Vision Library
The library has more than 2500 optimized algorithms, which includes a comprehensive set of both classic and state-of-the-art computer vision and machine learning algorithms. These algorithms can be used to detect and recognize faces, identify objects, classify human actions in videos, track camera movements, track moving objects, extract 3D models of objects, produce 3D point clouds from stereo cameras, stitch images together to produce a high resolution image of an entire scene, find similar images from an image database, remove red eyes from images taken using flash, follow eye movements, recognize scenery and establish markers to overlay it with augmented reality, etc.
-
product
Pendulum Impact Testing Machine
Direct indication of impact energy absorbed by specimen on large diameterAvailable with safety guard for the operatorInitial potential energy for Charpy is 300 Joules & for Izod is 170 Joules with a L.C. of 2 Joules (for Analogueodels) & resolution of 0.5 Joules (for Digital Model)Pendulum drop angle for Charpy is 140° & for Izod is 90°ASTM Impact Testing machine is also supplied, which conforms to E-23 ASTM standarAvailable with Gauges, Tongs, Sub-zero bath, Templates, U & V-Notch milling cutter (Optional)
-
product
Torsion Testers
10k to 300k in.lbf (1,000 to 30k N.m)
For maximum versatility and capability, Tinius Olsen offers a full range of torsion testing machines in capacities from 10,000-300,000in.lbf or kg.cm (1000-30,000N.m). Higher capacity and other longer length models are available on request.
-
product
Benchtop AOI Machine
Sherlock-300F
Many companies, especially smaller electronics manufacturers, put off adding automated optical inspection (AOI) to their process because of the high capital investment, the sharp learning curve, and the need for an experienced operator to program and fine-tune it. Benchtop Sherlock 300F AOI machine was designed to make in-house AOI affordable and manageable for first-article inspection, prototyping, and even full production inspection requirements. It features the same technology and quality build of the batch and inline Sherlock 300 models—plus the same two full days of installation and training at your facility offered with the other models*—in a smaller size, at a lower price point.
-
product
Accelerometers
An accelerometer is used in manufacturing machine maintenance to inspect equipment vibration. An accelerometer also is used in product testing to measure the vibration of various components.A triaxial accelerometer, also called a 3-axis accelerometer, provides measurements of the following parameters: vibration acceleration, vibration velocity and vibration displacement. In this way, vibration is measured and recorded with great precision.Most accelerometer products offered by PCE Instruments are portable devices. Many feature memory functionality so that readings can be stored and retrieved later for in-depth analysis. Some accelerometer models come with a manufacturer's calibration certificate. Some accelerometer models can be calibrated to ISO standards optionally for an additional fee.
-
product
High Temperature XY Planar Biaxial Extensometer 1200 C or 1600 C)
Model 7651
Jinan Testing Equipment IE Corporation
Model 7651 extensometers measure combined in-plane strains in flat cruciform specimens tested in machines capable of simultaneous X and Y (perpendicular) axial loading and on standard flat samples tested in pure tension. All models are capable of bi-directional displacement in both axes and may be used for strain-controlled fatigue testing under fully reversed load and strain conditions at frequencies up to 10 Hz.All 7651 models mount rigidly on the load frame and incorporate slide mounting to bring the extensometer into contact with the specimen. The gauge length is set automatically before mounting on the test specimen, which allows for hot mounting after thermal equilibrium has been reached.These units are specifically designed to eliminate crosstalk between axes and to provide high accuracy, high resolution measurements. They incorporate capacitive sensors for low operating force and include electronics with programmable filtering and multi-point linearization for improved performance and accuracy. The overall design minimizes, and in many cases virtually eliminates, any influence from common lab environment vibrations.These water-cooled extensometers are equipped with high purity alumina rods with conical rod tips for specimen contact when testing to 1200℃(2200°F). Silicon carbide rods are used for the 1600℃(2900°F) high temperature option.
-
product
Rubber Testing Machine
Dongguan Kejian Instrument Co., Ltd.
This machine is used to do the test of wear-resistant in surface, leather, cloth, paint, paper, flooring, plywood, glass and natural rubber. The method is using the standard knife cutting the specimen, and then using the regulated models of grinding wheel with loading weight to be abrased. Remove the specimen after rotation to reach a centain number, and then observe the condition of the specimen or compare the weight with the previous materials.
-
product
SWIR Line-Scan USB3 Cameras
NECTA S Series
NECTA S, the SWIR line-scan model in NECTA camera family, is capable of high-resolution acquisition in short-wave infrared bandwidth, ranging from 950 to 1700 nm. This new SWIR camera can reach up to 40kHz line rate with 14bit A/D converter: its high-speed USB3 interface, an advanced I/O, together with a compact and rugged aluminum case, make NECTA S suitable for most demanding machine vision applications.
-
product
Frazier Differential Pressure Air Permeability Tester
The Low Pressure Air Permeability Machine was developed by the National Institute of Standards and Technology of measuring the air permeability of textile type materials. and It is the acknowledged standard of the U.S. Government and the U.S. Textile Industry. The second model, High Pressure Air Permeability Machine is produced on the same principle as the Low Pressure Machine, but designed with a much greater versatility for use through its higher attainable airflow and differential pressure. Both models are extremely accurate and reliable, very easy to operate, and nearly maintenance free.
