Filter Results By:
Products
Applications
Manufacturers
Mixers
-
product
Double Balanced Mixers From 0.01 To 6000 MHz
A double balanced mixer (DBM) employs the use of a well matched quad-diode ring with two balanced transformers. Because of this, a DBM enjoys the inherent advantage of high port to port isolation. The IF port in Pulsar's DBM design is DC coupled to the diodes.
-
product
Mini Receiver
FB7-NX
In about 1935, the National Radio Company of Malden, Mass., brought out a “hot” high frequency receiver, called the FB7, and the subsequent FB-7X. It featured a super-hetrodyne design with plug-in coils that gave it a broad frequency range. The “X” model also incorporated a crystal filter in the intermediate frequency section, thus giving it additional selectivity. The receiver was viewed by radio amateurs as a technological breakthrough, and it was also used commercially for point to point high frequency communications. As the receiver did not have an internal RF amplifier section, a separately tunable RF amplifier was later provided in a separate enclosure for additional performance capabilities. Now, National RF, Inc., is resurrecting the fabled receiver name with an all solid-state, hot mini receiver, which also utilizes plug-in coils to cover the HF spectrum. The mini-receiver is designed for use by radio amateurs as well as serious short-wave listeners, and allows reception of AM, CW, and SSB signals. It incorporates a super-hetrodyne design with a dual gate FET built-in RF preamplifier and a ceramic filter for selectivity, often required when used in a crowded amateur radio band. In addition, the receiver has a buffered rear panel output of the high frequency oscillator for use with either a frequency counter for exact receive frequency display, or for interface with an outboard transmitter. A rear panel jack is also provided for muting the receiver when a transmitter is placed into the transmit mode. And, the receiver is small enough to fit into carry-on luggage and taken on trips when it is desired to “keep an ear” on amateur radio or other high frequency activity. The receiver utilizes rear panel plug-in coil assemblies which contain the RF amplifier, mixer, and oscillator tuned circuits. Each plug-in coil assembly also comes with a separate dial scale, which is inserted onto the front panel for displaying the tuned frequency. A very smooth 6 to 1 planetary drive is used for tuning the receiver. Other front panel controls include RF preamplifier peak, volume control, Beat Frequency Oscillator adjustment, and RF gain control. Other switches include filter bandwidth, AM/CW/SSB selection, Power, and a general coverage/band spread control for certain plug-in assemblies. The receiver is intended to drive head-phones via a rear panel jack, but has sufficient output to drive a small external speaker.
-
product
Digital Automatic Matrix Mixer
DM1624f
The DM1624F is a powerful digital audio processing, mixing and routing system. The primary applications are sound reinforcement and conferencing in boardrooms, courtrooms, worship centers, distance learning systems, hotels and other applications with multiple microphones and loudspeakers. The design represents a milestone in DSP technology in its basic architecture and in its processing speed and efficiency.
-
product
Honey Refractometer
BKPR-1
The MISCO Digital Honey Refractometer is designed for government honey inspectors, professional beekeepers, honey producers, honey mixers, honey brokers, or anyone requiring the absolute most accurate, repeatable readings of honey moisture content. Measure honey moisture content from 13 to 30%.
-
product
Schottky Barrier Ring Quads
SemiGen’s Silicon Schottky Diodes are designed for applications through 40Ghz. The special process technology utilizes various metal schemes to provide excellent performance of Low, Medium, and High Barrier applications. The end result is a low resistance diode with tightly controlled capacitance which allows for optimum performance. Low conversation loss and superior TSS make these diodes ideal for detector / mixer applications with frequency ranges from S band to Ka band as well as modulators, lower power limiters and high speed switches.
-
product
Receivers
Macom Technology Solutions Holdings Inc.
MACOM's receivers are widely used in point-to-point radio, aerospace and defense, and other broadband communications applications. Operating between the 4.5 - 45 GHz frequency range, our receivers feature an integrated LNA, mixer and LO buffer amplifier onto a single chip. Available in lead-free QFN or SMD packages, our receivers boast excellent noise figure and conversion gain performance.
-
product
Mixers
Macom Technology Solutions Holdings Inc.
MACOM's mixers are offered as single, double balanced, and image reject covering narrow and wideband frequencies up to 64 GHz. Mixers are used in both up and down frequency conversion applications. These discrete passive mixers are offered in bare die, surface mount package, and connectorized form factors.
-
product
2x8 Coherent Mixer With Single-ended Photodetectors
This page defines the requirement of a special coherent receiver with 8 single-ended photodiode outputs, per customer request. The coherent mixer, consisting of two polarization-diversified 90deg optical hybrids, a polarizing beam splitter and a beam splitter, is exactly same as existing DP-QPSK coherent mixer, and therefore offering same optical performance.
-
product
Spectrum Analysis For E5081A Up To 44 GHz
S960907B
The Keysight S960907B spectrum analyzer (SA) software application adds high-performance microwave spectrum analysis capabilities to the Keysight ENA-X up to 44 GHz. With fast stepped-FFT sweeps resulting from optimized data processing, the SA application provides quick spurious searches over broad frequency ranges. Conduct simultaneous spectrum measurements using test and reference receivers. For efficient measurements of spurious signals emanating from mixers and frequency converters, combine the multi-channel SA with the internal swept-signal generators. The SA application employs source-power and receiver-response calibration as well as fixture de-embedding, providing in-fixture and on-wafer spectrum measurements with the highest level of accuracy.
-
product
Spectrum Analysis, Up To 26.5 GHz
S930902B
The S930902B spectrum analysis adds high-performance microwave spectrum analysis to the PNA family up to 26.5 GHz. With fast stepped-FFT sweeps resulting from optimized data processing, the SA application provides quick spurious searches over broad frequency ranges. Simultaneous spectrum measurements can be done using up to five test and reference receivers. This multi-channel SA can be used with the internal swept-signal generators for efficient measurements of spurious signals emanating from mixers and frequency converters. The SA application employs source-power and receiver-response calibration as well as fixture de-embedding, providing in-fixture and on-wafer spectrum measurements with the highest level of accuracy.
-
product
Tracking Generators
TG100 and TG200
The TG100 and TG200 are generic Tracking Signal Generators. They can be used with a variety of spectrum analyzers from different manufactures. The TG200 is a wider coverage version of the TG100. This accomplished by separating the isolation amplifier assembly from the two mixers supplied with the TG200. For a complete discussion of the TG100/200 down load the zip-file TG ARTICLE(~1MB). This article goes into detail on the operation and performance of the TG100/200 system. It includes photos, plots, block diagrams and text.
-
-
product
In-line Metal Mixers
Nordson EFD in-line metal mixers’ housings and elements are made primarily of stainless steel. This makes them ideal for high-pressure applications and easy to clean and reuse.
-
product
Differential And I/Q Device Measurements
S95089B
The S95089B combines source-phase control of multiple internal or external sources with frequency-offset mode, enabling simplified test of I/Q modulators/converters, differential mixers, and harmonics or amplifiers.
-
product
Waveguide Harmonic Mixers (smart mixer), 60 to 90 GHz
M1970E
The Keysight M1970E 60 to 90 GHz waveguide harmonic mixer is an un-preselected mixer that will extend the operating frequency range of the N9030A PXA, N9020A MXA,and N9010A EXA signal analyzers up to 90 GHz. Smart features are embedded to help you to greatly simplify your overall test setup and improve the DANL and TOI of your test system. Go smart with harmonic mixing for your millimeter-wave applications.
-
product
Sub-Harmonic Mixers
Subharmonic mixers are composed of a passive mixer with a subharmonically pumped (×2) local oscillator. These mixers allow designers to use low LO frequency, which eases the need to generate a high frequency LO signal. For high frequency application design, Analog Devices subharmonic mixers offer a simpler alternative to traditional mixers with no LO multiplier.
-
product
RF Switch Matrices
For applications involving the test and measurement of multiple RF components, Teledyne Coax offers Custom Switch Matrix solutions to integrate multiple switches, along with additional components including filters, mixers, and attenuators, as required. These Custom Switch Matrix units can contain SPDT, Transfer, or Multi-Throw Switches in either Multiple Input Multiple Output (MIMO) or Multiplexer (MUX) configurations.
-
product
Double-Balanced Mixer, 18 to 46 Ghz
MAMX-011054
Macom Technology Solutions Holdings Inc.
MAMX-011054 is a double-balanced passive diode mixer housed in a 3 mm, 12-lead AQFN package. The mixer offers low conversion loss, high linearity and a wide IF bandwidth. The double-balanced circuit configuration provides excellent port isolation while internal 50 Ω matching simplifies its application. MAMX-011054 is also available in die form. Refer to datasheet MAMX-011037-DIE. This mixer is well suited for applications such as test and measurement, microwave radio and radar.
-
product
IQ Mixers
The new MMIC IQ mixers from Fairview (also known as IQ modulators) utilize a highly reliable GaAs MESFET semiconductor process which integrates a pair of matched double balanced mixer cells, a 90-degree hybrid and a 0-degree splitter/combiner that produces exceptional amplitude and phase balance performance. This level of integration offers size and performance advantages in comparison to discrete module assemblies. With the addition of an external 90-degree IF hybrid module, these IQ mixers can be used as either a Single Sideband Up-converter Mixer or an Image Reject Down-converter Mixer. The benefit of image rejection and sideband suppression can reduce overall system cost and complexity by removing the need for pre-selection filtering. Typical applications include point-to-point and point-to-multipoint radio, VSAT, military radar, electronic warfare, satellite communications, test equipment, and sensors.
-
product
Frequency Converters
Ducommun's frequency converter families include waveguide detectors (FAS), passive and active multipliers (FMP and FMA), up and down converters (FUB and FDB), harmonic mixers (FDH), subharmonically pumped up and down converters (FUS and FDS) and phase detectors and single sideband modulators (FPB and FSS). These devices are offered in 7 waveguide bands to cover entire 18 to 110 GHz frequency spectrum. These converters employ high performance GaAs Schottky beamlead diodes and DLT's proprietary circuit configuration to produce superior performance, such as low conversion loss and up to full waveguide instantaneous operation bandwidth.
-
product
Components - Harmonic Mixers (WHMB)
WHMB Series
Farran Technology manufactures a comprehensive range of waveguide harmonic mixers for use with industry standard spectrum analysers and other custom applications. Models WHMB are fully calibrated broadband balanced diode units covering 26.5-110 GHz in standard waveguide bands. We also offer a low cost general purpose model WHMP covering 26.5-170 GHz.
-
product
Single connector for a HG cable, and two HM connectors
MVNA-8-350-2
The lower part of the Central Unit model MP-8-350-2 has a single connector for a HG cable, and two HM connectors (Fig. 9). Two Harmonic Mixers can work simultaneously, for instance HM2 detecting transmission through the DUT, and HM1, at port 3 of a directional coupler, detecting reflection from the DUT.
-
product
Safety Test Panel for Mixer
SCR ELEKTRONIKS introduces Safety Test Panel for Domestic Mixer with PC Datalogging. The tests are Performed as Prescribed in IS the Panel Carries out different tests one by one and provides indication of the Test results as OK or NOT-OK. It is very useful and handy in line testing on Mass production line as well as type Testing. Special fixture can be provided for the specific product. This avoids the connections & disconnections of the product for different tests. The total time for entire testing is less than 20 seconds. Micro controller based sequential timer maintains the sequence of operation and displays the test status. This manual contains information about operating instructions and maintenance of the equipment. Please go through this manual carefully and retain it for future reference.
-
product
Noise Figure Measurements With Vector Correction
S95029B
The S95029B noise figure application enables high-accuracy noise figure and noise-power measurements of amplifiers, frequency converters, and mixers by using the Keysight vector-source-correction technique. Using a source-impedance tuner to remove the effects of imperfect system-source match, this technique produces higher accuracy results than Y-factor method and other cold-source implementations--especially for in-fixture, on-wafer, and automated-test environments.
-
product
Waveguide Harmonic Mixers (smart mixer), 75 to 110 GHz
M1970W
The Keysight M1970W 75 to 110 GHz waveguide harmonic mixer is an un-preselected mixer that will extend the operating frequency range of N9030A PXA, N9020A MXA,and N9010A EXAsignal analyzers up to 110 GHz. Smart features are embedded to help you to greatly simplify your overall test setup and improve your DANL and TOI of your test system. Go smart with harmonic mixing for your millimeter-wave applications.
-
product
Mixed Gas Generators MU Series
MU-2200
The mixed gas generator MU Series integrates with high-performance mass flow controllers to generate a homogenous gas mixture of two or more types of gases. Using the control unit’s touch panel you can control both flow rate, and the concentration of the mixed gas.The gas generators can be used for industrial purposes, such as generating combustion gases supplied to burners, as well as laboratory use in the biotechnology and food markets. HORIBA produces gas mixers tailored to customers’ intended uses, such as models with a purge function capable of mixing reactive gases.
-
product
DI Boxes
Applied Research and Technolgy
Instrument DIs for stage and studio, plus specialized tools to connect virtually any source to a mixer, interface, or PA.
-
product
In-line Plastic Mixers
Ideal for one-use fluid dispensing, Nordson EFD’s disposable static mixers eliminate the need to worry about premature curing of materials.
-
product
PNA-X Network Analyzers
Keysight's PNA-X is more than just a vector network analyzer. It is the world’s most integrated and flexible microwave test engine for measuring amplifiers, mixers, frequency converters, and other active devices. The hardware includes two internal signal sources, a signal combiner, S-parameter and noise receivers, pulse modulators and generators, and a flexible set of switches and RF access points. These hardware features provide a powerful core for a broad range of linear and nonlinear measurements, all with a single set of connections to your device under test.
-
product
MMW Downconverters
Innovative Technical Systems has designed numerous microwave and millimeter-wave downconverters for a variety of applications. Typical downconverters include balanced mixers, phase-locked local oscillators, LO multipliers, and output IF amplifiers. RF LNAs are also provided for many downconverters up to 100 GHz.These downconverters can be designed for numerous communications, radar, and instrumentation applications. We will customize these converters for frequency coverage ,noise figure, gain, and mechanical form-factor.
