Filter Results By:
Products
Applications
Manufacturers
Motion Controllers
Coordinate motion and timing.
-
product
Motion Control
ADLINK motion control solutions have been widely adopted, to date driving over 700,000 axes industry-wide. ADLINK’s extensive field experience has driven the development of powerful, high-efficiency rapid response pulse motion controllers, real-time network controllers such as EtherCAT, Ethernet and MotioNnet, and application-level software for operating control systems with over 400 APIs
-
product
Ruggedized Field Deployable Tester
PUMA
- 18-slot PXI / 4-slot SCXI Chassis- 1.2 GHz Embedded Controller- 4-axis Motion Controller/Simulation- 8-port RS-232 Serial Module- 4-port RS-485 Serial Module- 48 bit Isolated Digital I/O- Reconfigurable multi-function I/O FPGA Module- 5 1/2 digit DMM- 200 MHz 2-channel Scope/Digitizer- Multi-function Data Acquisition (DAQ)- 8-channel Analog Input Module- 6-channel Analog Output Module- General Purpose Switching- RF suite (optional)
-
product
Advanced 4-Axis Servo & Stepper Motion Controller With Modular Design
PCIe-8154
The PCIe-8154 delivers high-frequency pulse rates up to 6.55 MHz and hardware-controlled emergency stop, software security protection, card index switching, and simultaneous linear/ circular run, exceeding industrial cost/performance requirements. Compatible with Mitsubishi, Panasonic and Yaskawa servos and any pulse-train controlled servo and stepper drives, the PCIe-8154 allows complex moving patterns through multiple axes that move with linear and circular interpolations using continuous contouring. Applicable for a variety of linear and circular trajectories, the PCIe-8154 delivers the smoothest motion control for a wide range of manufacturing applications. Modularized configuration accommodates ADLINK extension boards for distributed I/O control and high-speed triggering functions.
-
product
16-Axis PCIe EtherCAT Master Motion Controller
PCIe-8332
ADLINK PCIe-8332 is a hardware-based EtherCAT motion controller able to support up to 16 synchronized axes and over 10,000 points simultaneously. The PCIe-8332 features dedicated isolated emergency stop input (EMG), and configurable isolated high-speed digital input as not only generic sensor input but also pulsar input, with up to 1MHz input frequency. Optimum jitter control is provided in minimal cycles of 250µs to optimize synchronous I/O performance for vertical automation applications in semiconductor, electronic manufacturing, and others. The PCIe-8332 provides an out-of-shell application-ready (APS) function library to generate multi-dimensional, highly synchronized, time-deterministic event-triggered motion & I/O control. A wide range of compatible 3rd party slaves are easily designed with ADLINK's APS function library. ADLINK's MotionCreatorPro 2 utility is fully compliant with the Microsoft Windows environment, that allows complete EtherCAT motion and I/O configuration and function evaluation as well as compiling program download functions.
-
product
IC-3171, 1.9 GHz Intel Celeron Dual-Core Processor, 4-GigE Port, 2-USB 3.0 Port Industrial Controller
784963-01
The IC‑3171 is a high-performance, fanless industrial controller for developers who require a high level of processing power and connectivity for automation and control applications in extreme environments. The IC‑3171 provides connectivity for communication and synchronization to EtherCAT and Ethernet CompactRIO chassis, EtherCAT motion drives, GigE Vision and USB3 Vision cameras, and other automation equipment. In addition, this controller has onboard isolated, TTL, and differential digital I/O, so it can perform synchronization and control tasks without additional tethered I/O.
-
product
4-Axis Motorized Micromanipulator
Quad
Quad, the newest Sutter Instrument motorized micromanipulator, is easy-to use and features four independent axes. Each axis has a 25 mm range of motion, a digital display of position and an ROE control. The compact, intuitive controller takes up minimal bench space, is fan free and is easy to use.
-
product
Voltage Input Module For Remote I/O
The Voltage Input Module for Remote I/O features 2-, 3-, and 4-wire spring terminal connection methods, a built-in power supply for sensors, four selectable input ranges, and simultaneous sampling. A remote I/O system consists of an EtherCAT bus coupler and individual modules mounted on a DIN rail. You control the Voltage Input Module for Remote I/O from a real-time controller, such as a CompactRIO Controller or an Industrial Controller. You can use remote I/O hardware to add low-cost I/O for simple tasks while your controller handles advanced tasks such as image processing, motion control, and high-speed or specialty measurements.
-
product
EtherCAT Slave System
EPS Series
The ADLINK complete EtherCAT solution, from hardware to middleware to software, with every element tailored for dedicated EtherCAT functionality, includes PCIe-833X Series master controllers, EPS slave systems, and remote monitoring and control providers. As well, ADLINK’s Softmotion one-stop control kernel delivers flexible and easy-to-use intelligent platforms for driving next-generation modern Smart Factories. ADLINK's EPS slave system brings the power the flexibility to EtherCAT environments. State-of-the-art modular construction allows the EtherCAT slave to be configured to fulfill the needs of both small local applications and expansive distributed platforms. The EPS system with comprehensive and high-density I/O modules that include DI/O, pulse-chain motion modules. Leveraging ARM and FPGA technologies, the EPS slave is able to monitor and report system integrity via EtherCAT communication, while relay module lifecycle and signal integrity of analog output are monitored cyclically, and hot swappability reduces downtime significantly. Uniquely designed for full operability in conditions from -20°C to 60°C,the EPS slave system is also fully compliant with the EN 60068-2 standard for shock and vibration and EN 61000-6 for heavy industrial EMC protection, as well as emission certification. Corresponding ESI files for each EPS system can be generated thru ADLINK's Windows-based EtherCAT slave utility, LinkMasterPro™.
-
product
Single-Axis Rate and Position Tables
The wide range of potential customer specifications is accommodated by a number of standardized or customized tables. They are distinguished by differing electrical drive technologies (direct drive, belt drive), table tops, motion controllers (COTS, ACUTROL®3000e), and various options (table tops, temperature chambers, accessories).
-
product
4-Axis Pulse Motion Controller Advanced Motion Control For Servo/stepper Motor
AMP-304C
AMP-304C is an advanced 4-axis motion controller card with a PCI Express® interface that can generate a pulse train up to 9.99MHz to control a motor. With more general purpose as well as dedicated IOs, functional logic selection switches, 4-channel encoder feedback input, AMP-304C can be used for a multitude of scenarios or applications.
-
product
IC-3121, 1.91 GHz Intel Atom Quad-Core Processor, 2-USB3 Port Industrial Controller
784961-01
1.91 GHz Intel Atom Quad-Core Processor, 2-USB3 Port Industrial Controller - The IC‑3121 is a compact and rugged industrial controller that withstands the harsh environments common in automation, supervisory control, distributed control, and industrial embedded OEM applications. The IC‑3121 offers two USB3 ports with dedicated bandwidth, FPGA-based I/O capabilities, and network connectivity for distributed control applications. The advanced features include the ability to synchronize image inspection results with industrial I/O and configure hardware-timed network triggers to trigger camera acquisition, motion control, or data acquisition. You can use the advanced FPGA personality that is shipped with the system or customize the FPGA functionality using the LabVIEW FPGA Module.
-
product
EtherCAT Master Multi-Axis Motion Controllers
DMC-52xx0
The DMC-52xx0 EtherCAT Master is Galil Motion Control's first 32 axis motion controller. It is a pure EtherCAT controller capable of controlling up to 32 drives and 2 IO modules on one EtherCAT Network in a small, space efficient package. The DMC-52xx0 makes configuration and programming easy with just a handful of EtherCAT configuration commands and Galil’s intuitive, two-letter programming language. The DMC-52xx0 is offered in 2, 4, 8, 16, and 32 axis formats. Coordinated moves can be done within banks of 8 allowing for minimal changes to Galil’s programming language. Galil supports a variety of EtherCAT drives to accommodate most applications. The DMC-52xx0 operates in Cyclic Synchronous Position mode (CSP). In this mode the servo control loop is closed on the EtherCAT drive while the Galil sends motion profile data at a 1 kHz rate. The DMC-52xx0 features 8 uncommitted opto-isolated inputs and 8 uncommitted opto-isolated high power outputs. It also includes 8 uncommitted analog inputs and 8 uncommitted analog outputs. One 100 Mbps Ethernet port and one USB (serial) port are provided for communication with a host PC or external devices.
-
product
Ethernet Motion Controllers
DMC-21x3
Galil's DMC-21x3 Ethernet motion controllers are designed for extremely cost-sensitive and space-sensitive applications. These controllers are typically half-the-price and half-the-size of box-level Ethernet controllers. These intelligent, card-level controllers can be purchased with plug-in, multi-axis amplifier boards which eliminate wiring between the controller and drives.
-
product
Integrated Vision System
GEVA 312T
The GEVA-312T is an integrated vision system complete with a 12” touch screen display, 1.6GHz dual core processor and two Gigabit Ethernet camera ports. The slim-line form factor maximizes control panel real estate for PLCs, motions controllers and non-vision related components. The GEVA-312T is a good choice for customers who are looking for a complete system that is low-cost, expandable and applicable for a wide range of vision applications.
-
product
DSP-Based 4/8-Axis Advanced Motion Controllers
PCI-8254/8258
ADLINK's new PCI-8254 and PCI-8258 incorporate up-to-date floating-point DSP and FPGA technology to provide high-speed and high performance hybrid analog and pulse-train motion command. Leveraging ADLINK Softmotion technology, the PCI-8254/PCI-8258 offer more comprehensive and application-oriented motion functions to reduce the development time but maintain superior throughput and accuracy. Also delivered is excellent synchronous motion control performance.
-
product
Gearbox Tester
The gearbox tester was designed to test the Azimuth Drive Unit (ADU) for a missile launcher. The ADU is the horizontal position controller for the launcher. It consists of a main drive shaft, a manual drive shaft and an output drive shaft. This system uses a multi-axis motion controller to operate.
-
product
REM-11100, 2-, 3-, 4-Wire, 4-Channel Voltage Input Module for Remote I/O
784748-01
2-, 3-, 4-Wire, 4-Channel Voltage Input Module for Remote I/O - The REM‑11100 is a voltage input module for remote I/O. Remote I/O systems are low-cost, modular systems for simple machine control and measurements. A remote I/O system consists of an EtherCAT bus coupler and individual modules mounted on a DIN rail. You control the REM‑11100 from a real-time controller, such as a CompactRIO Controller or an Industrial Controller. You can use remote I/O hardware to add low-cost I/O for simple tasks while your controller handles advanced tasks such as image processing, motion control, and high-speed or specialty measurements. This module features 2‑, 3‑, and 4‑wire spring terminal connection methods, a built-in power supply for sensors, four selectable input ranges, and simultaneous sampling.
-
product
Real-Time Motion Controller
Advantech provides two types of motion controller: PC-Based Programmable Motion Controller and Standalone ARM-based Motion Controller.
-
product
High Speed Load Cell Test Interface
LCIC-4CH
Industrial Measurement Systems Ltd.
The latest stand-alone controller model: LCIC-4CH, was specially designed to fit portable wheel and axle scales for determining the weight of trucks or heavy vehicles either in static mode or in motion, with very high accuracy and very friendly to operate. The In-motion speeds up the weighing process and allows weighing a truck without the need to stop.In the last 16 years, our stand-alone High-Speed weighing-in-motion controller model: LCIC-WIM was sold all around the world and as for today, thousands are being in use when among our customers are some well known weighing manufacturers.Most of our customers around the world are scale manufacturers or integrators that were able to offer the market the most advanced WIM scale with very short time to market and minimum R&D expenses.
-
product
Entry-Level 4-Axis Servo & Stepper Motion Controller
PCI-8134A
The PCI-8134A is a 4-axis entry-level motion controller. A PCI interface provides plug-and-play capability for easy maintenance, and supports up to 12 cards in one system, to control 48 motors. The PCI-8134A provides pulse train command output up to 2.4MHz and encoder input up to 2.4MHz in 4xAB phase mode. Programmable acceleration and deceleration allows flexible programming of in-house applications, and dedicated motion I/Os shorten system installation. The PCI-8134A also supports 2~4 axis linear interpolation for simplified synchronous motion. The PCI-8134A is a cost-effective motion controller enabling implementation and control of most of point-to-point, conveyer, and load-and-unloader applications.
-
product
PMAC Advanced Motion Controllers
Powerful motion control for the most demanding applications.
-
product
Advanced 2-Axis Servo & Stepper Motion Controller
PCi-8102
PCI-8102 is an advanced stepper/servo motion controller to meet high performance/cost ratio request. Compared with PCI-8132/PCI-8134, PCI-8102 mainly offers three features: Software security check for users' software, card ID setting and circular interpolation control. Besides, PCI-8102 also provides users many additional features with cost-effective way. For details, please refer to the user manual.
-
product
DSP-Based 4/8-Axis Advanced Pulse-Train Motion Controllers
AMP-204C/AMP-208C
ADLINK"s new AMP-204C/AMP-208C DSP-based 4/8-axis advanced pulse-train motion controllers incorporate up-to-date floating-point DSP and FPGA technology, enabling high pulse output and encoder input frequency up to 6.5 MHz and 20 MHz respectively. Leveraging ADLINK" s Softmotion technology, the AMP-204C/AMP-208C offer impressive comprehensive and application-oriented motion functionality to reduce development time while maintaining superior throughput and accuracy. Superior synchronous motion control performance combines with point-table function integrating multi-dimensional interpolation, such as 3D linear/circular/spiral interpolation with enhanced trajectory and velocity planning, for contouring applications in semiconductor, display and conventional manufacturing industries. The AMP-204C/AMP-208C also support PWM control with three different control modes for frequency or duty cycle, benefiting laser engraving/marking/cutting applications. Moreover, hardware-based position comparison and trigger output are applicable in AOI applications.
-
product
PCI Bus Controllers
DMC-18x6
The DMC-18x6 PCI bus controllers belong to Galil's latest generation motion controller family: the Accelera Series. Incorporating a 32-bit Risc-based microcomputer, these new controllers offer high-speed performance and processing power. Speed improvements include acceptance of encoder inputs up to 22 MHz, servo update rates as low as 24 microseconds/axis, and command execution speeds as low as 40 microseconds
-
product
Hand-Held, Battery-Operated Multi-Frequency Eddy Current Instrument
US-454A
United Western Technologies Corp
The US-454A is a portable, hand-held, battery-operated multi-frequency eddy current instrument that can be connected to a laptop, PC and motion controllers for use in semi- or fully automatic data collection applications. Two encoder inputs enable position stamping of data. Pulse-on position input is ideal for motion control applications. Ethernet and USB capabilities allow instrument control along with time- and position-stamped data transfer to the client computer. Built from the rugged US-454 architecture, the US-454A offers single- and multi-frequency inspection, frequency mixing capabilities, enhanced signal-to-noise ratio, USB, Ethernet and data storage capability, and unprecedented digital strip chart data collection.
-
product
Motion Control
Welcome to Thorlabs; below you will find links to our selection of Motion Control products, a subset of our entire line of photonics products. Thorlabs’ motion control products are separated into manual and motorized linear and rotation stages, multiaxis platforms, actuators, and controllers. The manual and motorized stages can frequently be configured into 1-, 2-, or 3-axis solutions. Since many of the stages are available in either manual or motorized versions, creating a custom system is easy. For nanopositioning applications like waveguide and fiber coupling, our line of multiaxis flexure stages are ideal. Both the motorized stages and the multiaxis platforms are supported by a complete line of controllers for the various motors and piezoelectric actuators. In addition, we support custom and OEM motion control applications with an extensive line of manual, motorized, and piezo actuators as well as threaded adjustment screws.
-
product
24-Bit Precision Load Cell Input Card
PCI-9524
The PCI-9524 is a robust, multi-purpose module designed for turnkey material test systems (MTS). Equipped with four strain gauge-based transducer input channels, four general purpose analog input channels, and a 3-axis motion controller, the PCI-9524 delivers a complete hardware solution for MTS manufacturers. The PCI-9524 easily integrates physical quantity measurement and implements strategy of close-loop control in a single module package. For transducer measurement, the PCI-9524 supports sensitivity from 1.0 mV/V to 4.0 mV/V and provides a 1/200000 accuracy of measurement of full scale. These features make the PCI-9524 suitable for precise measurement in large-scale transducers.
-
product
Stand-Alone Motion Controller
DMC-2000 Series
The DMC-2000 stand-alone motion controller is a member of the Optima Series, Galil's full-featured multi-axis motion controllers. The DMC-2000 is the first motion controller in the market designed for the high-speed, flexible Universal Serial Bus (USB)-which is projected as the industry standard for local network communications between PCs and peripherals.
-
product
IC-3171, 1.9 GHz Intel Celeron Dual-Core Processor, 4-GigE Port, 2-USB 3.0 Port Industrial Controller
784964-01
The IC‑3171 is a high-performance, fanless industrial controller for developers who require a high level of processing power and connectivity for automation and control applications in extreme environments. The IC‑3171 provides connectivity for communication and synchronization to EtherCAT and Ethernet CompactRIO chassis, EtherCAT motion drives, GigE Vision and USB3 Vision cameras, and other automation equipment. In addition, this controller has onboard isolated, TTL, and differential digital I/O, so it can perform synchronization and control tasks without additional tethered I/O.
-
product
Regulators, Monitoring, Sensors And Flow Control
All of the products in Parker's extensive pump and flow control product lines, from pumps and valves to motors and motion controllers, share a common heritage of advanced technology applied to meet the specific needs of our customers. In every instance and for every application, Parker components and systems are engineered to deliver precise and reliable control.
