Filter Results By:
Products
Applications
Manufacturers
Physical Layer
Tests hardware, electrical and procedural interface to the transmission medium.
-
product
PXI/PXIe MIL-STD-1553 Multiplexer, Dual 16-Channel, 2-Pole
42-739-002
The 40-739-002 (PXI) and 42-739-002 (PXIe) are dual 16-channel 2-pole multiplexers designed specifically for physical layer multiplexing or demultiplexing differential signals that conform to the MIL-STD-1553 specification. The module can be supplied as a single or dual 16-channel 2-pole multiplexer with each signal pair having a controlled 78 Ohm differential impedance.
-
product
PXI DeviceNet Interface Module
PXI DeviceNet Interface Modules have an onboard microprocessor and optically isolated physical layer to communicate with a DeviceNet network system as a master (scanner) or slave device. The modules ship with a high-level API that provides complete access to a DeviceNet network and features easy access to device data and streamlined explicit messaging. PXI DeviceNet Interface Modules are ideal for prototyping DeviceNet systems, PC-based control, embedded control systems, PC-based human machine interface (HMI), and DeviceNet network management utilities.
-
product
Avionics Interfaces & Test Instruments
ARINC 664
Avionics Interface Technologies
AIT’s ARINC 664 test instruments can be used in test and simulation applications that are required to transmit and receive data over the ARINC 664 avionics databus. AIT’s instruments use small form-factor pluggable transceivers (SFP) and support copper or fiber optic physical network interfaces.Using an FPGA based architecture, with multiple embedded processors, the ARINC 664 instruments provide onboard support for upper layer protocol processing (A653, UDP, IP) and utilize DMA to provide optimal data throughput. All ARINC 664 protocol operations, including VL traffic shaping, redundancy management, and IP fragmentation and reassembly, are handled onboard.
-
product
Combination Module: 2 Ch. MIL-STD-1553 & 12 Ch. Discrete I/O
CM8
The CM8 module is a combination of NAI's MIL-STD-1553B module, FTB, and Enhanced Discrete I/O module, DT4. The CM8 offers twelve channels of discrete I/O and two channels of MIL-STD-1553B communications. The twelve discrete I/O channels are programmable as either input (voltage or contact sensing with programmable, on-module pull-up/pull down current sources), or output (current source, sink, or push-pull) up to 500 mA per channel from an applied, external 3-60 VCC source. The discrete I/O channels also provide additional functionality modes such as Pulse Width Modulation (PWM) output mode and Pattern Generator output mode. The two MIL-STD-1553B communications channels feature a dual, redundant, balanced-line, physical layer; a (differential) network interface; time division multiplexing; half-duplex command/response protocol; and up to 31 remote terminals (devices).
-
product
SDH Ethernet Testers
Wuhan Sunma Technology Co., Ltd.
The SunmaFiber SDH & Ethernet is easy to use, cost effective Ethernet testing solution for basic physical layer cable testing, layer 2 and layer 3 traffic generation, and full RFC 2544 testing. The rugged, battery operated, application specific test tool enables field technicians to turn-up Ethernet and IP services by running an RFC 2544 test or following a set of methods and procedures. The product has been designed for front-line technicians who do not have experience dealing with emerging Metro Ethernet technologies and need a simple to use solution for Ethernet and IP testing.
-
product
Digital Services
*Processor verification experience*Memory verification*Bus protocols and DMA verification*Expert in high speed controller verification*Physical layer (PHY) verification
-
product
PXI CANopen Interface Module
The PXI CANopen Interface Module is a high-speed CANopen interface for developing applications with the NI-Industrial Communications for CANopen driver. CANopen is the application layer that sits on top of the CAN physical layer often used for industrial automation applications. The PXI CANopen Interface Module can transmit/receive PDOs and SDOs according to CiA DS301. It also features a batch SDO editor with electronic data sheet (EDS) file integration and layer setting services (LSS) support for slave node configuration.
-
product
NFC Physical Layer Test System
IQnfc+
LitePoint provides turn-key software that facilitates test coil calibration, executes test plan and provides detailed waveform analysis and flexible APIs to customize test flow in the labs.
-
product
PXI/PXIe MIL-STD-1553 Multiplexer, Dual 8-Channel, 2-Pole
40-739-004
The 40-739-004 (PXI) and 42-739-004 (PXIe) are dual 8-channel 2-pole multiplexers designed specifically for physical layer multiplexing or demultiplexing differential signals that conform to the MIL-STD-1553 specification. The module can be supplied as a single or dual 16-channel 2-pole multiplexer with each signal pair having a controlled 78 Ohm differential impedance.
-
product
Development Switch
AFDXSwitch Lab
The AFDXSwitch Lab operates in accordance to all requirements specified in the ARINC 664 part 7 standard. Features include traffic policing and frame filtering functions as well as integrity and error checking of frames. Additionally the switch comes with advanced features like 1 Gbit/s speeds, flexible physical layer configuration and extended environmental ratings. The AFDXSwitch Lab provides the full range of all technical functionalities of TTTech’s certifiable AFDX production switches, making it the optimal switching solution for a large variety of different application areas.
-
product
PCIe 5.0 Protocol Analyzer
P5552A
The Keysight P5552A PCIe 5.0 Protocol Analyzer introduces a new form factor that is easily deployable in the lab bench environment to enable deep protocol analysis of a PCIe system with unparallel signal integrity. Locate protocol errors or validate device operations by viewing data from the physical layer all through the transactional layer with ease.
-
product
GAOTek Handheld Gigabit Ethernet Test Module
A0070008tek
GAOTek Handheld Gigabit Ethernet test module is a highly efficient test instrument which designed for Ethernet layout and integration tests which conforms to Ethernet test standards. This instrument is required for testing from physical layer to service layer of emerging (or next generation) networks. The Ethernet tester is the new Ethernet tester to qualify Ethernet service over LAN and RAN deployment. This is a highly efficient test instrument for service providers to ensure SLA KPIs with the subscribers.
-
product
Efficient And Effective Physical Layer (PHY) Testing Of 10/100/1000Base-T Interfaces
Explore Sifos Technologies’ highly unique, plug’n play 10/100/1000Base-T Ethernet Physical Layer Testing Solutions. Cost Effective and Comprehensive PHY Testing without Scopes, Fixtures, Probes, and Test Signals.
-
product
Isolated Controller Area Network (CAN)
ADI isolated controller area network (CAN) transceivers provide the differential physical layer interface between the data layer link, hardware protocol (for example, embedded in some of ADI's Blackfin® processors), and the physical wiring of the CAN bus. ADI's portfolio includes transceivers with integrated iCoupler® and isoPower® isolation, providing, fully isolated off-the-shelf CAN PHY's.
-
product
PXI-8532, 1-Port, PXI DeviceNet Interface Module
781063-01
1-Port, PXI DeviceNet Interface Module—The PXI‑8532 is a high-speed DeviceNet interface for developing applications with the NI‑Industrial Communications for DeviceNet driver. DeviceNet is based on the CAN physical layer and increases strength and interconnectivity by specifying various parameters, such as the required cable length, connectors, and baud rates. DeviceNet specifications are managed by OVDA, Inc. You can program the PXI‑8532 to add high-performance master/scanner or slave capabilities to DeviceNet networks.
-
product
SpaceWire Physical Layer Tester
141
The SpaceWire Physical Layer Tester (SPLT) is a tool designed to test, validate and verify a SpaceWire system across all levels of the SpaceWire standard. Two SpaceWire ports employ a special LVDS interface which allows the transmitted signals to be deliberately and measurably manipulated to test the capability of a unit under test to receive signals of varying quality.
-
product
Ethernet Controller ICs
CP220x
The CP220x family is the industry's smallest single-chip Ethernet controller containing an integrated Media Access Controller (MAC) and Physical Layer (PHY).
-
product
PXI/PXIe MIL-STD-1553 Multiplexer, Dual 4-Channel, 2-Pole
40-739-006
The 40-739-006 (PXI) and 42-739-006 (PXIe) are dual 4-channel 2-pole multiplexers designed specifically for physical layer multiplexing or demultiplexing differential signals that conform to the MIL-STD-1553 specification. The module can be supplied as a single or dual 16-channel 2-pole multiplexer with each signal pair having a controlled 78 Ohm differential impedance.
-
product
NI-9881, 1-Port C Series CANopen Interface Module
781673-02
The NI‑9881 is a high-speed CANopen interface for developing CANopen applications in LabVIEW software on CompactRIO hardware. CANopen is the application layer that sits on top of the CAN physical layer often used for industrial automation … applications. It was designed for motion-oriented machine control networks, such as handling systems, but now it is used in a variety of applications, including medical equipment, off-road vehicles, maritime electronics, public transportation, and building automation. The NI‑9881 can transmit/receive process data objects (PDOs) and service data objects (SDOs) according to CiA‑DS 301. The NI‑9881 is compatible with only CompactRIO systems.
-
product
Development Switch
AFDXSwitch Lab v2.0
The AFDXSwitch Lab v2.0 is identical to the TTESwitch A664 Lab v2.0, which fully supports AFDX® and operates in accordance with all requirements specified in the ARINC 664 part 7 standard. Features include traffic policing and frame filtering functions as well as integrity and error checking of frames. Additionally, the switch comes with advanced features like 1 Gbit/s speeds and flexible physical layer configuration. The TTESwitch A664 Lab v2.0 is based on the TTESwitch Module A664 Pro, thus providing the full range of technical functionalities of TTTech’s certifiable AFDX switch modules and making it the optimal switching solution for a large variety of different application areas.
-
product
2 Channels, MIL-STD-1553, Dual Redundant, Direct Coupled, Assisted Mode Capable (AMC)
FTE
MIL-STD-1553 is a military standard published by the United States Department of Defense that defines the mechanical, electrical, and functional characteristics of a serial data bus. It was originally designed for use with military avionics, but has also become commonly used in spacecraft On-Board-Data-Handling (OBDH) subsystems, both military and civil. It features a dual, redundant, balanced-line, physical layer; a (differential) network interface; time division multiplexing; half-duplex command/response protocol; and up to 31 remote terminals (devices).
-
product
Physical Layer Switching Systems for copper LAN, WAN, DSL, Telco apps with RJ style connectors.
RJ Series
The RJ Series of computer controlled switching systems are designed for physical layer switching of multiwire signals on RJ style connectors. Since the system uses mechanical relays it acts exactly like a piece of cable which makes it perfect for testing networks without altering the signals or regeneration. These systems are typically used for Ethernet LAN 10BaseT through 1000BaseT, DSL including ASML through GFAST, CAT5 through CAT6A cable testing, USB up to 2.0, RS232, RS422, RS485 up to 8 wire at 20 Mbps and many other applications switched over RJ45 connectors up to 8 wires. They may also be used as lab automation switches, network testing switches, patch panels, network redundancy switches or any number of physical layer applications.
-
product
Network Cable Tester
NCT-500
ShinewayTech NCT-500 Network Cable Tester，Functions ranging from ISO / OSI reference model physical layer, link layer, network layer multiple detection. One machine in hand, which can quickly locate network faults and determine the link quality.
-
product
PXI/PXIe MIL-STD-1553 Multiplexer, Dual 16-Channel, 2-Pole
40-739-002
The 40-739-002 (PXI) and 42-739-002 (PXIe) are dual 16-channel 2-pole multiplexers designed specifically for physical layer multiplexing or demultiplexing differential signals that conform to the MIL-STD-1553 specification. The module can be supplied as a single or dual 16-channel 2-pole multiplexer with each signal pair having a controlled 78 Ohm differential impedance.
-
product
CCIX
The CCIX® Consortium was founded to enable a new class of interconnect focused on emerging acceleration applications such as machine learning, network processing, storage off-load, in-memory data base and 4G/5G wireless technology. CCIX is a high performance, low latency interface that is based on PCIe Physical layer, up to speeds of 32GT/s. Teledyne LeCroy provides a range of Protocol Analysis tools to support development and debug of CCIX based devices.
-
product
GSM/EDGE Analysis Using NI PXI RF Test Instruments
NI-RFmx GSM/EDGE
The NI-RFmx GSM/EDGE personality is a highly optimized API for performing physical layer measurements on GSM/EDGE cellular standard signals. NI-RFmx GSM/EDGE is completely interoperable with all NI-RFmx APIs. It provides simple access to the most advanced optimization techniques such as multi-measurement parallelism and multi-DUT measurements. The result is extremely fast and high-quality measurements with minimal software development effort.
-
product
Iridium Physical Layer Test Systems
PLTS
Averna has worked with Iridium to ensure you have the right equipment to support their test coverage. The Iridium PLTS verifies product performance to Iridium’s standards. Find out more!
-
product
Fiber Testers
Shenzhen Noyafa Electronic CO.,LTD
Provides a powerful combination of physical layer tools to troubleshoot copper/fiber links and LAN tools to identify and repair a wide range of network problems.
-
product
QualiPhyer Tools
QualiPhyer is a family of software packages used to test a product’s conformance to IEEE 802.3™ and MIPI Alliance electrical and optical standards for Ethernet and MIPI devices. These packages can be used to control oscilloscopes and traffic generators over Ethernet or GPIB connections to test the physical layer characteristics of devices. The software processes waveforms from the scopes to produce results based on algorithms developed at the UNH-IOL.
-
product
SAEJ1962M-DE9M CAN OBD-II Cable, SAE J1962 to D-sub 9-pos F, 2m
193942-02
9-Pin, Male SAE J1962 OBD-II Type A to 9-Pin, Female D-SUB - The OBDII9M-DB9F CAN Cable, sometimes referred to as the CAN OBD-II Cable, connects any NI high-speed CAN interface to an OBD-II compliant vehicle that has high-speed CAN on its diagnostic link connector in the passenger compartment. This high-quality injection-molded cable connects the CAN wires from the SAE J1962 connector to the standard CiA-DS-102 D-SUB connector wiring used by NI CAN interfaces. This cable is available with a high-speed CAN physical layer and no termination.
