Filter Results By:
Products
Applications
Manufacturers
Potentiometers
Measure the voltage in a circuit or function as voltage dividers.
See Also: Programmable Resistors
-
product
Suitable For Temperature And Potentiometer Sensors
SEM1600T
The SEM1600T accepts resistance or mV signals from RTD, Slidewire or Thermocouple sensors.
-
product
Evaporation Gauges
Evaporation gauges determine the evaporation rate by measuring the changing water level in an evaporation pan. The gauges consist of a float, pulley, and counterweight attached to a potentiometer mounted through a gear assembly in weatherproof housing. The evaporation gauges produce a resistance output that dataloggers can measure.
-
product
PCI High Density Potentiometer Card 5-Channel, 8-Bit, 0 To 255 Ohm
50-296A-021-5/8
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Potentiometer for OEMs
FlexiPot
The best user interface, whether in consumer electronics or industrial controls, contains sensors that cause minimal interference, meaning the user may not even know they are there. FlexiPot, by Tekscan, is a flexible membrane potentiometer with an ultra-thin (0.008"), lightweight profile. Low power requirements combined with a linear output make it the ideal position sensor, from both a manufacturing perspective as well as a user perspective.
-
product
Automotive Rotary Potentiometers
Panasonic Industrial Devices Sales Company of America
Panasonic Center Space Rotary Potentiometers offer built-in LED options and automotive operating temperatures. Target markets include Automotive and Measurement Equipment.
-
product
Life Cycle & Fatigue Testers
Switches can use all these operations. Membrane switches, keyboards and keypads will all require a push with a known force. On/Off switches will combine a push and a pull or possibly push on, push off. A rocker switch and toggle switches will require a push in two different places. Rotary switches (and volume controls, potentiometers) need to be rotated clockwise and counter clockwise The standard life cycle and fatigue tester the B886 Simon System has been designed for life cycle and fatigue testing of switches, membrane switches, keyboards and keypads. It contains all the components needed to life and fatigue test a products that need to be pushed. We can also supply different actuators for a push, pull, rocker, toggle, volume control or rotary switch.
-
product
PXI Potentiometer Module 5x8 Bit, 0 Ohm to 255 Ohm
40-296-021-5/8
The 40-295 is a Programmable Resistor module with up to 18 channels of 8-bit resolution resistor chains in a single 3U PXI module. The flexible architecture allows these modules to also be supplied as 12, 16 or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count.
-
product
Precision Pots Single-turn
Precision potentiometers are designed for control applications where accuracy and high-reliability is important. Theses devices are available in conductive plastic, wirewound or Hybritron® element types, and in various sizes. Both single-turn and multiturn models are available.
-
product
Linear Motion Potentiometers
A spin-off of the Trimpot trimming potentiometer product line, the linear motion potentiometer was developed to meet the needs of designers wishing to detect movement of position. Applications for these compact components include: Solenoid positioning sensors for automated controllers, volume control on audio equipment, joystick controllers, satellite dish positioning, and robotics.
-
product
Digital Potentiometers
DigiPOT
Analog Devices portfolio of digital potentiometers provide uncompromising performance across a wide range of industrial temperatures. Sometimes called digital pots, RDACs, or digiPOTs, these compact devices can be used to calibrate system tolerances or dynamically control system parameters. DigiPOTs such as the AD5123 and AD5143 offer a nonvolative solution for 128-position/256-position adjustment applications, with low resistor tolerance and the low temperature coefficient simplifying open-loop applications and those that require tolerance matching.
-
product
Signal Conditioning & Control
Offering a wide variety of products from amplifiers and comparators to redrivers, microcontrollers, data converters (ADC) and digital potentiometers (POTs).
-
product
Mini-Joystick Potentiometers
The CTS mini-controllers offer these features often found in many larger products:A choice of through hole or surface mountingA long 1 million cycle lifeA variety of resistance and tolerance optionsExcellent electrical accuracy with a patented mechanism (Pat. Nos.: US 7,199,314, Taiwan 279822, Pat. Pending in China)An optional momentary switch that is operational at all positions to allow excellent navigation and menu selection
-
product
PXI Standard Programmable Resistor Modules
Pickering's PXI Standard Programmable Resistor Modules include fully programmable resistor and potentiometer modules for applications such as sensor emulation that require fine adjustment with a resolution down to 0.25 Ohm. All of our Programmable Resistor Modules can easily be formed to make Programmable Potentiometers by connecting two channels in series, using the unconnected terminals as the A and B connections and the link between the two channels as the wiper connection. For applications with more demanding accuracy and resolution requirements, consider our Precision Programmable Resistor Modules .
-
product
Signal Splitters
The DAT4530 can convert any process signal (Thermocouples, RTD, mV, Voltage, mA Resistance and Potentiometer) to a voltage or current output (4-20mA, 0-20mA or 0-10V). Each output can be different and it also has a built in limit alarm which is an SPST relay. The DAT4530 is PC programmable with the aid of the Prodat programmer and the Datasoft software which is available from the Datexel down load page. The DAT4530 is also programmable with the aid of 3 DIP switches which can be found on the side of the DAT4530. There is full isolation between the input, power supply, limit alarm output and two outputs.
-
product
Long Travel Extensometers
The first type is specifically aimed at the plastic and rubber industries to provide accurate readings of strain and extension over a large extension range. The unit, incorporating two clamping arms and precision potentiometers, produces a DC voltage proportional to the distance between the arms. This generates accurate readings of percentage strain and allows additional parameters such as yield point and break points to be calculated when used with NEXYGENPlus software.
-
product
Potentiometer, Level Transmitter, Position Transmitter
Model TWP / TWP2
Kusam Electrical Industries Limited
• Aux. Power AC 85 ~ 265V or DC 85 ~ 300V• High Accuracy 0.1% RO at 23 ° C - 5 °C• Input / Output User Selectable• PC Plastic Case, DIN Rail or Wall Mounting• High Dielectric Strength (AC 1.5KV/Min, between Input / Output / Power)
-
product
Input Devices
Panasonic Automotive & Industrial Systems Europe GmbH
Panasonic's Electromechanical Components are used to convert mechanical movement into electrical signals. These products, including switches, encoders, and potentiometers, are used in everyday devices at the point of user interaction.
-
product
Power Monitor, AC-Powered, Field Adjustable
YMA/YQA
NAI's YMA and YQA Power Monitors are used to monitor voltage, frequency, and phase characteristics of single- or three-phase power lines. This allows normal operation of system loads when the power-line characteristics are within predetermined limits.High and low voltage and frequency limits, and "pick-up" and "drop-out" time delay are field-adjustable using potentiometers. These power monitors are ideally suited for rugged defense and industrial applications.
-
product
PCI High Density Potentiometer Card 3-Channel, 24-Bit, 0 To 16M Ohm
50-296A-121-3/24
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Motorized Potentiometer
Mounting On Circuit Board Or DIN Rail
INELTA Sensorsysteme GmbH & Co. KG
*PCB mounting*Suitable as: setpoint device or rotary actuator*Compact in design* Robust aluminium housing* Gear safety clutch
-
product
Amplifier Built-in Ultra-compact Laser Sensor
EX-L200
Panasonic Industrial Devices Sales Company of America
The EX-L200, the one of the world’s smallest Laser Sensors with a built-in amplifier, is designed to detect minute objects with utmost accuracy. Despite its miniature size, the Thru-Beam Type (EX-L211) can detect minute objects with a diameter of just 0.3mm, and the Spot Reflective Type (EX-L221) can even detect gold wire whose diameter is a mere 0.01mm. To facilitate solving application tasks, these sensors come equipped with a Potentiometer and two indicator LEDs. For the Thru-Beam Type, reflective material on the receiver allows users to visualize the laser beam, easing beam-axis alignment.
-
product
PCI High Density Potentiometer Card 4-Channel, 12-Bit, 0 To 4k Ohm
50-296A-121-4/12
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Linux-based Development Platform For The GridARM™ ΜController
PEAK gridARM Evaluation Board
The ARM7 microcontroller gridARM™ was developed by Grid Connect® as a system on a chip solution (SoC) for the implementation of embedded applications with a focus on industrial communication. The Evaluation Board PEAK-gridARM is a Linux-based development platform for the gridARM™ microcontroller. It has connections for Gigabit Ethernet, high-speed CAN, USB 2.0, RS-232, SPI and I²C. The digital and analog inputs of the evaluation board can be manipulated with buttons and potentiometers. The states of the microcontroller, the supply and the message traffic are displayed via LEDs. A board support package for Linux enables access to the hardware resources of the PEAK-gridARM evaluation board.
-
product
Economic Type Potentiometer Indicator
CS1-PM
CS1-PM economic type Potentiometer Indicator has been designed with high accuracy measurement, display and communication of resistance (3 wires) as like as Positioner.The meter supports Field Calibration function. It can be calibrated with sensor (Potentiometer) to meet machinery structure.They are also available 1 option of 1 Relay outputs, 1 Analogue output or 1 RS485 (Modbus RTU Mode) interface with versatile functions such as control, alarm, re-transmission or communication for a wide range of machinery and testing equipments applications.
-
product
Potentiometers
We offer wear-free, low-cost potentiometers that work exceptionally well anywhere precise and careful controls, inputs, or measurements are needed. If your application needs displacement and/or angle sensors, Hoffmann + Krippner, in exclusive partnership with German manufacturer Altmann GmbH, can provide high-quality potentiometer solutions. Furthermore, Hoffmann + Krippner’s ultra-thin, fully-sealed, and easily customized Sensofoil® membrane potentiometers can fit into restricted installation conditions and offer extremely long lifecycles. Similarly, Hoffmann + Krippner SensoInk® allow us to create polymer potentiometers that combine the advantages of PET (flexibility and cost) with high-strength polymer pastes that can surpass the lifecycles of other PET-based potentiometer products.
-
product
X-Band Motion Detector
32213
The X-Band Motion Detector’s sensor is a common component in security systems and automatic door openers and can detect movements within a room, yard, or even on the other side of a wall. The X-Band Motion Detector operates in the X-band frequency, at 10.525 GHz and indicates detected movements with oscillations in its high/low output. Sensitivity is manually adjustable with a potentiometer, offering direct line of sight detection from roughly 8 to slightly over 30 ft (~2.4 to 9+ m).
-
product
Plug and Play Potentiometer Input Module
DSCUSB-PT
The DSCUSB-PT is a compact, high-precision potentiometer input module; converting a resistance based input (potentiometer) to a digital output. Can be used with resistance based sensors to indicate position, rotation and angle. Aimed at applications which require high accuracy. Simply by plugging the device into a PC, data can be extracted from the potentiometer input to the DSCUSB-PT for a wide range of applications. This is achieved using the DSCUSB Toolkit software, which is a simple configuration tool designed specifically for configuring DSCUSB modules. It allows configuration, calibration, logging and parameter management of the modules.
-
product
Contacting Linear Motion
A spin-off of the Trimpot trimming potentiometer product line, the contacting linear motion position sensor was developed to meet the needs of designers wishing to detect movement of position. Applications for these compact components include: Solenoid positioning sensors for automated controllers, volume control on audio equipment, joystick controllers, satellite dish positioning, and robotics.
-
product
PXI Potential Divider Module 24-Channel (no resistors fitted)
40-282-121
The 40-282 is a potential divider with up 24 separate channels. This can be used to emulate potentiometer devices, each channel having a fixed R1 R2 ratio. Additionally, the centre point can be shorted to either of the potentiometer end points.
-
product
Rotary Position Sensors For Motorsport
Variohm offer a range of Rotary Position Sensors For Motorsport including rotary potentiometers and hall effect sensors. They are suitable for use in Morotsport application such as pedal, steering and gearbox applications.
