Filter Results By:
Products
Applications
Manufacturers
Probe Stations
system to contact DUTs to drive and receive signals.
See Also: Probe Systems, Flying Probes, Manual Probe Stations, Cryogenic Probe Systems
-
product
Semi-Automated Probe Stations
SPS 2600, SPS 2800, and SPS 12000 Series
The SPS 2600, SPS 2800, and SPS 12000 Series systems are MicroXact’s semi-automated probe stations designed to be flexible and easy to use when performing high productivity device characterization, wafer level reliability testing and failure analysis. These semi-automatic probe station systems are designed to support manual and semi-automatic probing of up to 200mm wafers.
-
product
Probe Stations
PSI's 600LS Series Probe Station is designed to exceed performance metrics of equipment priced significantly higher.
-
product
Technical Manual Probe Station
4060 150-200 mm
Micromanipulator's Tech Series Probe Station, Model 4060 is designed to provide a quality 6-inch (150mm) or 8-inch (200mm) probe station at a cost effective price
-
product
Cryogenic Probe Station
CryoPro
Materials Development Corporation
The MDC Model 441 Cryogenic Probe Station is a cost effective alternative to high-priced vacuum based cryogenic probe stations. With up to five probes available and sample diameters up to six inches, the MDC Cryogenic Probe Station allows for electrical measurements at temperatures near liquid nitrogen levels (77K).
-
product
Automated DC Parametric Curve Tracer
MegaTrace
MegaTrace supports pin counts greater than 625 up to 2160 pins, with 1080 pins being popular. Comprised of a cart that contains the test chassis, PC monitor, drive bus box, and a test interface, MegaTrace is easy to move around and use with other instruments like emission microscopes, probe stations, and other remote testing requirements.
-
product
Microscope Spectrophotometer
508 PV
The 508 PV™ Microscope Spectrophotometer is designed to add spectroscopy, color imaging, thin film thickness measurement and colorimetry capabilities to your optical microscope or probe station. It can also be used to upgrade an older microspectrometer with cutting edge optics, electronics and software.
-
product
Portable Wafer Probe Station
PS-5026B
High Power Pulse Instruments GmbH
The PS-5026B is a rugged portable wafer probing solution which has been designed for high reliability, compact size and minimum cost.
-
product
Probe Cards
PICOPROBE® PROBE CARDS by GGB Industries, Inc., allows for more chip design flexibility because each probe card is custom configured to your circuit for testing wafers on either manual or automatic probe stations. Probe cards with complex layouts consisting of numerous DC contacts and multiple microwave probes with operating frequencies of 40, 50, 67, or 110 GHz can be custom fabricated quickly and inexpensively.
-
product
Semi-Automatic LCD Probe Station/Laser Repair System
LCD 2424
The Model 2424 Semi-Automatic LCD Probe Station is designed especially for probing LCDs and other large substrates. Built on a steady and reliable anti-vibration table, the Model 2424 has powerfully built features that perform a number of specific tests required by all LCD/flat panel display manufacturers.
-
product
C-V Plotters
Materials Development Corporation
MDC will tailor your CSM/Win Semiconductor Measurement System for your exact requirements. Choose the best capacitance meter, output device, and probe station for your needs. All CSM/Win C-V plotters feature the latest Dell Computers. The computer and capacitance meters are rackmounted in one compact enclosure. When ordered with a hot chuck or probe station, MDC can deliver a turnkey system of unparalleled performance.
-
product
Cryogenic Probe Station
CRX-4K
Designed for versatility and high performance, the CRX-4K is our premium cryogen-free closed-cycle refrigerant probe station. This system is the solution for those looking for the convenience of cryogen-free operation and the exceptional measurement performance of a Lake Shore product.
-
product
Probe Station
ETCP1000
Installation of “Hot and cool chuck” - Sellectable chuck size : 4inch, 6inch. - Temperature variation : -193°C ~ 300°C (80K ~ 573K) - Additional requirements : Vacuum chamber, LN2 tank(Bombei), microscope, CCD camera, manipulators. - EPS500 is standard model in ETCP1000 probe station.
-
product
Stimulus Induced Fault Testing
SIFT
SIFT allows for the analysis of numerous stimuli to identify speed, fault, and parametric differences in silicon. The heart of the SIFT technique revolves around intentionally disturbing devices with external stimuli and comparing the test criteria to reference parts or timing/voltage sensitivities. Synchronous interfacing is possible to any tester without any wiring or program changes. The system can be based on either a motorized probe station or portable microscope stand for test head applications.
-
product
Starter Probe Station
C Series
Contains fundamental features to probing. C series lets you kick off your experiments and is an entry level machine designed for ease of use while allowing you to get accurate, reliable results.
-
product
Line Automation Equipment
5000 Series In-line Handler
The Circuit Check 5000 Series In-line Handler is an integrated inline solution that combines automation, fixturing and measurement hardware in addition to other in-line PCBA probe based test stations, while adding a standardized quick change fixture interface. The 5000 series in-line is a unified solution that is software and hardware agnostic, enabling adaptability to a variety of off-the-shelf lower cost ICT, flash and functional test software and hardware.
-
product
Probing Solutions
ES62X-CMPS
The ES62X-CMPS compact manual probe station is a rugged wafer probing solution designed for high reliability, compact size and low investment cost. It enables manual wafer level measurements up to 300 mm wafers. The probing station can also be used for TLP, HMM, HBM, LV-Surge, RF, S-parameter and DC-measurements. Micro positioners with vacuum as well as magnetic base can be attached. The chuck has a vacuum interface for the wafer and is electrically isolated. Multiple 4 mm connectors can be used to connect a voltage potential to the wafer backside.
-
product
Complete Probe Station
BD Series
Best for DC and RF probing, the platen lift is designed for smooth raise and contact of your probes simultaneously to your device. It is ideal for probing multiple spots on your device, or through multiple devices.
-
product
Semi-automatic 150mm Probe Station
CM460
CM460 Semi-automatic 150mm probe station step & repeat, point & shoot, color mapping, and complete software control.
-
product
Flying Probe Programming & Test Development
Testing House offers full Flying Probe Programming and Test Development using its very own Seica Pilot LX Flying Probe Test Stations.
-
product
High Power Devices
SemiProbe configures our PS4L Adaptive Architecture into the Voltarus (TM) family of probe stations to fulfill the unique requirements of testing high power devices at wafer level prior to packaging. Voltarus probe stations are available in manual, semiautomatic, and fully automatic configurations that can test and characterize power devices up to 10 KV or 200 Amps (pulsed).
-
product
Probe Station
EPS300
Reasonable price and compact design. - Sellectable chuck size : 4inch, 6inch, 8inch when ordering probe station. - Hot chuck can be installed. Temp range: RT ~ 300°C - Hot and cool chuck from 0 °C ~ 300 °C can be provided.
-
product
Powerful, Fully Integrated Workstation for Emission Microscopy
PEM-1000
The PEM-1000 emission microscope incorporates the latest technology in real time, high quantum efficiency, mega-pixel CCD detectors in a back-thinned cooled camera. A portable system, the PEM 1000 can interface with all analytical probe stations, ATE (automated test equipment) and bench top configurations for high speed functional testing.
-
product
Controlled Environment Probe Station
CG-196
Everbeing controlled environment probe station allows vacuum and cryogenic probing down to 77K with liquid nitrogen or high temperature probing up to 1273K. Efficient in characterizing your devices at extreme temperatures, vacuum, specific gas, etc.
-
product
Portable Manual Probing Station
Model W4.0 x L6.5
This portable manual probing station is designed for a versatile, comfortable, and accurate operation on up to 4.0” wafers or 4.0” X 6.5” printed circuit board assemblies. This turn-key, manually operated probing station, model W4.0 x L6.5, is part of the D-COAX commitment to the test and measurement and PCB fabrication industries.
-
product
Cryogenic Probe Station
FWPX
Lake Shore’s FWPX probe station is designed for researchers who require large-size wafer probing. The FWPX accommodates wafers up to 102 mm (4 in) in diameter and can be modified to accept up to 152 mm (6 in) wafers. This general-purpose probe station is designed for researchers or engineers conducting material characterization tests over large samples. It is also an effective unit for measuring organic materials.
-
product
Probe Systems
These flexible probe stations are designed for the ever-changing test configurations required in a engineering lab. Combined with durable probes or your own high-speed probes, PacketMicro probe stations are the most cost-effective probing solutions in the industry.
-
product
MmW Probe Station
EB-6V
The EB-6V probe station is designed for all frequency extenders such as those from VDI, OML, R&S, Keysight, Anritsu. If you are using an Anritsu VNA VectorStar ME7838A4 model, or commonly Anritsu 3743A mmW Extenders and related sizes, the station of interest is the EB-6A.
-
product
Fully Manual Systems
SPS-1000, SPS-2000, and SPS-2200
The SPS-1000, SPS-2000, and SPS-2200 systems are MicroXact’s premier manual probe stations designed to be flexible and easy to use. The high level of performance and affordability of these manual probe systems put them in a class of their own.
-
product
Nano Technology Products
We are instrumental in offering quality range of nano technology products that find application in defense research and development organization. Our range encompasses probe station, microscope, extension cable, adopter and RF probing, and vibration isolation products. We have the ability and resources to design products in line with the exact specifications provided by the clients.
-
product
Optoelectronics and Photonics
SemiProbe has developed probe stations for a wide variety of optoelectronic and photonic device applications, including light emitting diodes (LEDs), vertical cavity surface emitting lasers (VCSEL) and photo diodes. Testing and handling small, fragile, thin wafers with thousands of die on them poses unique challenges that require innovative solutions.
