Filter Results By:
Products
Applications
Manufacturers
USB Test
-
product
USB Test Hardware
Test stations with USB hardwareHardware control of adapters with USB-I / OFlash and microprocessor programmer
-
product
EBIRST 50-pin D-type Verification Fixture
93-005-101
The 93-005-101 50-pin D-type Verification Fixture is an accessory for the eBIRST range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
product
Catena 1910 HSIC Tester
Catena 1910
The MCCI Catena 1910 HSIC USB Tester enables testing of HSIC Host or HSIC Device products. It can be used to exercise your product by operating as an active host or active device, while simultaneously capturing USB traffic for analysis. For test and validation of a final system, Passive Capture mode lets you debug and verify communication between your HSIC Host and HSIC Device,
-
product
EBIRST 104-pin D-type Test Tool
93-022-001
The 93-022-001 eBIRST 104-pin D-type test tool is part of a range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces PXI, LXI or PCI controlled switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
product
Advanced Cable Tester v2
TP800110
The Total Phase Advanced Cable Tester v2 is the quickest and most convenient way to comprehensively test USB, Lightning, and video cables. It provides:*Short testing - Dynamic visualization of test results*Open testing - Dynamic visualization of test results*Continuity testing - Dynamic visualization of test results*DC resistance measurement for most wires, with milliohm precision on ground and power wires, ohm resolution on most other wires, continuity check only on high-speed data lines*Signal integrity testing of data lines to 12.8 Gbps per channel*E-Marker verification*Lightning plug bring up/function (Apple Lightning Cables)**Over-voltage protection (Apple Lightning Cables)**Voltage recovery testing (Apple Lightning Cables)**Quiescent current consumption (Apple Lightning Cables)*
-
product
EBIRST 96-pin SCSI Termination Fixture
93-016-103
93-016-103 eBIRST Termination Fixture is part of a range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces PXI, LXI or PCI controlled switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
product
EBIRST 9-pin Male D-type Termination Fixture
93-003-103
eBIRST is a range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces PXI, LXI or PCI controlled switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
product
USB 2-port Hub For Elan's USB T&M Instruments
USBMicroHub2
The USB MicroHub is designed to make it easy to connect multiple USB2.0 devices via a single USB port, and is ideal for use with the USB test and measurement family. Connecting multiple scopes, function generators and pulse generators together is made simple with this clever little unit.
-
product
Digital Multimeter
M3500A
USBTMC stands for USB Test & Measurement Class. Any USB device conforms to USBTMC without the limitations of operation systems and environment can work under VISA assistance, and communicate with a computer.In other words, the control procedures via VISA to USBTMC device and via VISA to GPIB device are the same.
-
product
EBIRST 50-pin D-type To 25-pin D-type Adapter
93-005-414
eBIRST is a range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces PXI, LXI or PCI controlled switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
product
EBIRST 200-pin LFH Verification Fixture
93-002-101
The 93-002-101 200-pin LFH Verification Fixture is an accessory for the eBIRST range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces switching solutions.. The tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
product
Ultra Portable SuperSpeed USB Analyzer
Advisor T3
Teledyne LeCroy’s Advisor T3 is an ultra portable SuperSpeed USB analyzer that delivers market leading accuracy at an extraordinary price. Designed to put precision USB protocol test tools in the hands of every engineer, the Advisor includes all the essential features for SuperSpeed USB debug.
-
product
EBIRST Slave Mode Connection Cable
93-970-301
eBIRST is a range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces PXI, LXI or PCI controlled switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
product
EBIRST 8-pin Male Power D-type Termination Fixture
93-012-103
eBIRST is a range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces PXI, LXI or PCI controlled switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
product
EBIRST 68-pin Male SCSI Termination Fixture
93-015-103
eBIRST is a range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces PXI, LXI or PCI controlled switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
product
EBIRST 100-pin SCSI Termination Fixture
93-019-104
93-019-104 eBIRST Termination Fixture is part of a range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces PXI, LXI or PCI controlled switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
product
EBIRST 104-pin D-type Verification Fixture
93-022-101
The 93-022-101 104-pin D-type Verification Fixture is an accessory for the eBIRST range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces switching solutions. The tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
product
Programmable USB Hubs & Multiplexers
Acroname's unique line of programmable USB products help automated tedious USB port handling and monitoring tasks. Simplify and automate USB testing in manufacturing test, validation, regression or stress testing of your USB products.
-
product
EBIRST 50-pin D-type Test Tool
93-005-001
eBIRST is a range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces PXI, LXI or PCI controlled switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
product
EBIRST 78-pin D-type To 68-pin Female SCSI Adapter
93-006-222
eBIRST is a range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces PXI, LXI or PCI controlled switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
product
EBIRST 23 X SMB Verification Fixture
93-011-101
The 93-011-101 23 x SMB Verification Fixture is an accessory for the eBIRST range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
product
MCCI USB Test Services
MCCI's Test Lab offers quick, cost-effective USB-IF Logo Compliance Testing for low-speed, full-speed and high-speed devices, and for low- and full-speed systems. As a certified logo-test facility, we can save you time, and give you expert advice.
-
product
S2 Spectra USB Sensors
ULP S2 SPECTRA USB
Universal LightProbe S2 Spectra USB Sensors test a wide range of LED intensities and any color in the visual spectrum, plus white, providing a linear response with a serial digital output via a PC. A standard USB Cable is provided to connect to a mini-type B five-pin USB connector, which is integrated into the S2 Spectra USB Sensor.Operating temperature range: 0oC to 70oCOutput Port: A standard mini-type B five-pin USB connector is integrated into the S2 Spectra USB Sensor,and a standard USB Cable is provided to connect to a USB portSensor Size: 0.560 in. dia x 1.38 in. long.Typical response time: < 10mS for color and intensity as a serial bit- stream (19200 baud rate)Fiber-Optic Probes: Can be paired with any of a wide range Universal LightProbe Fiber-Optic Probes
-
product
Rack Based Test Solutions
Most equipment manufacturers and large enterprises prefer rack-based test tools as they are compact and higher density form factor solution for testing, monitoring, and troubleshooting network conditions. GL’s Multiple TDM Optical and Packet (mTOP™) rack enclosure can house any combination of USB based test equipment which are easily deployed and securely fixed to an equipment rack to provide extraordinary scalability to test switches, routers and end-to-end networks. These rack based platforms incorporates the basic test unit along with the necessary PC hardware, Windows® 10 64-bit operating system and remote accessibility via scripting and remote desktop. There are no moving parts with the unit, so reliability and longevity are integral. GL’s latest mTOP™ Probe stand-alone hardware variant is an all-in-one self-contained test instrument. The mTOP™ Probe can include any of the multiple TDM Optical and Packet interfaces USB device combined with the PC into one single box. The comprehensive mTOP™ Probe hardware unit is designed for easier portability and convenient for field testing which incorporates the testing features for multiple interfaces along with necessary PC hardware in a single box. GL’s USB based test equipment - PacketExpert™ (Ethernet), tProbe™ (T1/E1), USB T3/E3 (TDM), Dual UTAs (Analog/Wireless), and LightSpeed1000™ (SONET SDH) to support multiple interfaces in a compact rack space or included in a portable Probe unit.
-
product
EBIRST 104-pin D-type To 100-pin SCSI Adapter Cable
93-022-245
The 93-002-245 104-pin to 100-pin eBIRST adapter cable is part of a range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces PXI, LXI or PCI controlled switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
product
EBIRST 78-pin D-type Test Tool
93-006-001
The 93-006-001 eBIRST 78-pin D-type test tool is part of a range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces PXI, LXI or PCI controlled switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
product
Multi-Interface TDM, Optical, And Packet/IP Rackmount & Probe Test Platforms
mTOP™
Most equipment manufacturers and large enterprises prefer rack-based test tools as they are compact and higher density form factor solution for testing, monitoring, and troubleshooting network conditions. GL’s Multiple TDM Optical and Packet (mTOP™) rack enclosure can house any combination of USB based test equipment which are easily deployed and securely fixed to an equipment rack to provide extraordinary scalability to test switches, routers and end-to-end networks. These rack based platforms incorporates the basic test unit along with the necessary PC hardware, Windows® 10 64-bit operating system and remote accessibility via scripting and remote desktop. There are no moving parts with the unit, so reliability and longevity are integral. GL’s latest mTOP™ Probe stand-alone hardware variant is an all-in-one self-contained test instrument. The mTOP™ Probe can include any of the multiple TDM Optical and Packet interfaces USB device combined with the PC into one single box. The comprehensive mTOP™ Probe hardware unit is designed for easier portability and convenient for field testing which incorporates the testing features for multiple interfaces along with necessary PC hardware in a single box. GL’s USB based test equipment - PacketExpert™ (Ethernet), tProbe™ (T1/E1), USB T3/E3 (TDM), Dual UTAs (Analog/Wireless), and LightSpeed1000™ (SONET SDH) to support multiple interfaces in a compact rack space or included in a portable Probe unit.
-
product
USB PD Test System
6050
Single Output USB PD USB PD basic version：the single-group test systemarchitecture is as shown in the table, 5302A AC Source, 3302F + 3310F series and9922-R Quick Charge Controller.
-
product
Battery Starting & Charging System Analyze
12-2415
*Shown with optional 12-2416 barcode scanner*Graphical Hand-Held Tester with Thermal Printer and USB Port*Tests 12V Flooded, AGM, Gel Cell, & EFB Batteries from 100 to 2000CCA*Graphical/Symbol Based LCD display*Tests 12/24V charging and electrical systems*Stores last 70 test series with or without power*Carrying case, printing software and USB cables included*Built-in thermal printer with thermal paper (611305)*Field-Replaceable Cables (900165)
-
product
EBIRST 78-pin D-type Verification Fixture
93-006-101
The 93-006-101 78-pin D-type Verification Fixture is an accessory for the eBIRST range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces switching solutions. The tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
