Elcometer Limited
For more than seventy years Elcometer has been a world leader in the design, manufacture and supply of inspection equipment to the coatings, concrete and NDT industry.
- +1 248 650 0500
- +1 248 650 0501
- sales@elcometer.com
- 6900 MIller Drive
Warren, Michigan 48092
United States of America
-
Product
Surface Cleanliness
-
Surface cleanliness: Soluble salts & ion specific contamination (sulphates, chlorides, nitrates etc.) which are often invisible to the eye, together with amine blush (for amine cured epoxy coatings) can result in premature coating failure, resulting in high re-coating and maintenance costs. Elcometer has a range of test equipment for assessing surface cleanliness prior to applying a coating.
-
Product
Setaflash ‘Series 3’ Closed Cup Tester
6910/1
-
The Elcometer 6910/1 Setaflash 'Series 3' Closed Cup Tester is an easy to use instrument that can complete a flash/no flash test in less than two minutes or determine the flash point of a sample within a temperature range of ambient to 300°C (ambient to 572°F).
-
Product
Pfund Thickness Gauge
3233
-
Available in aluminium or stainless steel this instrument consists of two concentric cylinders, one sliding inside the other. A spherical glass lens, which has engraved measurements, is fitted to the end of the central cylinder and when pressed into the wet film, leaves a circular trace.The diameter of the mark on the lens is measured and, using the supplied conversion table, the thickness of the coating can be easily assessed.Ideal for measuring the thickness of wet translucent products such as varnishes, oils etc.Measurement range of 2.25 - 360μm (0.09 - 14.17mils)
-
Product
Hardness & Scratch Resistance
-
Hardness can be defined as a material’s resistance to permanent deformation. In the coatings industry, hardness measurement can be used to determine the resistance of the coating to scratching from general wear and tear and also if a coating is fully cured.
-
Product
Cross Hatch Adhesion Tester
1542
-
The Elcometer 1542 Cross Hatch Adhesion Tester is ideal for measuring the cross hatch adhesion of coatings up to 250µm (9.8mils) on flat surfaces and test panels.
-
Product
Surface Profile
-
Surface profile: The degree of profile on the surface affects a coating’s overall performance and determines aspects such as adhesion, coverage and overall volume of coatings used. If the profile is too large the amount of coating required increases, otherwise there is a danger that the peaks remain uncoated - allowing rust spots to occur. If the profile is too small there may be an insufficient key for adequate adhesion.
-
Product
FORD/ASTM Viscosity Cups
2351
-
The Elcometer 2351 FORD/ASTM Viscosity Flow Cups are very easy to use instruments made of anodized aluminium with a stainless steel orifice, for measuring the consistency of paints, varnishes and similar products.
-
Product
Holiday Detector
266
-
The Elcometer 266 Holiday Detector revolutionises high voltage DC testing of coatings porosity detection making it safer, easier and more reliable than ever before.
-
Product
Fineness of Grind Gauges
2020
-
The Elcometer 2020 Fineness of Grind Gauges is used to determine the particle size and fineness of grind of many materials including paints, pigments, inks, coatings, chocolates and other similar products.
-
Product
Surface Comparators & Magnifier
127
-
Designed for use with the Elcometer 127 illuminated magnifier, each surface comparator has a hole in the centre allowing for clear visual comparisons to be made.
-
Product
DIN Viscosity Flow Cups
2350
-
The Elcometer 2350 DIN Viscosity Flow Cups are very easy to use instruments made of anodized aluminium with a stainless steel orifice, for measuring the consistency of paints, varnishes and similar products.
-
Product
Abrasive & Blast Inspection
-
Blasting parameters: A number of important parameters need to be monitored during the blasting or water jetting process, these include: air pressure (at the nozzle), nozzle diameter, blast media contamination & pH values in order to avoid recontamination of the substrate during blasting.
-
Product
Concrete Coating Thickness Gauge
500
-
The Elcometer 500 Coating Thickness Gauge accurately measures the thickness of coatings on concrete and other similar substrates* - non destructively.
-
Product
Punched Wet Film Combs (Aluminium)
112AL
-
The Elcometer 112AL, being punched from aluminium, is not as accurate as precision formed stainless steel wet film combs and has a shorter lifespan.
-
Product
Protective Coating Inspection
Kit 4
-
The Elcometer Protective Coating Inspection Kit 4 provides a range of test equipment to help an inspector assess a substrate prior to the application of a coating.
