Elcometer Limited
For more than seventy years Elcometer has been a world leader in the design, manufacture and supply of inspection equipment to the coatings, concrete and NDT industry.
- +441613716000
- +44 (0)161 371 6010
- sales@elcometer.com
- Edge Lane
Manchester, England M43 6BU
United Kingdom of Great Britain and Northern Ireland
-
Product
Qualicoat Powder Coating Inspection Kit
-
The aim of Qualicoat is to establish the minimum standard that plant installations, coating materials and finished products which have been powder coated must meet.Within this quality label, Qualicoat identifies a range of inspection requirements to be undertaken with regards to the quality control of powder coated products.The Elcometer Qualicoat Powder Coating Inspection Kit provides the various test instrumentation required to meet the high standards of this organisation.
-
Product
Cross Cut Adhesion Tester
1540
-
The Elcometer 1540 Cross Cut Adhesion Tester is a simple instrument for quickly determining the coating adhesion of a large variety of paints up to 50µm (2 mils) thickness.
-
Product
Manual Clemen Unit
Elcometer 3000
-
The Elcometer 3000 Manual Clemen Unit is a robust and simple to use instrument for evaluating the resistance to scratching of a coated surface.
-
Product
Pfund Thickness Gauge
3233
-
Available in aluminium or stainless steel this instrument consists of two concentric cylinders, one sliding inside the other. A spherical glass lens, which has engraved measurements, is fitted to the end of the central cylinder and when pressed into the wet film, leaves a circular trace.The diameter of the mark on the lens is measured and, using the supplied conversion table, the thickness of the coating can be easily assessed.Ideal for measuring the thickness of wet translucent products such as varnishes, oils etc.Measurement range of 2.25 - 360μm (0.09 - 14.17mils)
-
Product
Needle Pressure Gauge
102
-
The Elcometer 102 Needle Pressure Gauge is designed to measure air pressure up to 20bar (300psi) in blast and air hoses. Pressure drop is responsible for decreased production rates, increased abrasive consumption and reduced anchor profile in abrasive blasting systems.
-
Product
Duct Deposit Measuring System
-
The Elcometer 456 Duct Deposit Measuring System has been specifically designed to meet the requirements of the DTT (Deposit Thickness Test) in HVCA’s (Heating & Ventilation Contractor’s Association) Guide to Good Practice, for the measurement of dust and grease deposits within ventilation systems and kitchen ducts made of ferrous metals.
-
Product
DIN Scratching Tool
1538
-
The Elcometer 1538 DIN Scratching Tool has interchangeable carbide cutters for the preparation of specimens to be used for corrosion testing.
-
Product
Surface Comparators & Magnifier
127
-
Designed for use with the Elcometer 127 illuminated magnifier, each surface comparator has a hole in the centre allowing for clear visual comparisons to be made.
-
Product
Chloride, Sulphate & Nitrate Kit
134 CSN
-
Supplied in an ABS plastic carry case for easy portability around the site, each field kit is supplied with full instructions attached to the inside lid, together with:5 x Chloride tests5 x Sulphate tests, together with 1 x colorimeter, for sulphate testing5 x Nitrate test strips5 x Syringes (without needles)
-
Product
Conical Mandrel Bend Tester
1510
-
The Elcometer 1510 Conical Mandrel Bend Tester is used to determine the effects of bending on the elasticity, adhesion and elongation properties of cured coatings on sheet metal.
-
Product
ISO Scratching Tool
1537
-
The Elcometer 1537 ISO Scratching Tool is a simple but effective instrument that is used to scratch the surface of samples in preparation for adhesion, salt spray and corrosion tests.
-
Product
Viscosity & Flow Measurement
-
Viscosity is perceived as ‘thickness’ or resistance to pouring, but there is more to viscosity than this. All fluids have an internal friction between molecules, which determines how well fluid flows. Due to this internal friction, energy is required to move the liquid and viscosity is the measure of the resistance to flow. Elcometer manufactures and supplies a wide range of viscosity gauges from flow cups to dip cups to rotational viscometers.
-
Product
Inspection Kits
-
Elcometer offers one of the widest ranges of inspection equipment available. Our products are used across numerous industry sectors. In all cases, there is always a need to undertake a number of specific inspections during quality control assessments - as one parameter can affect another.
-
Product
Elcometer Testex® Replica Tape
122
-
Elcometer 122 Testex® Tape consists of foam with a non-compressible backing. The foam side is rubbed into the surface providing a permanent mould of the peak-to-valley profile. The profile of the surface can then be measured using the Elcometer 124 Thickness Gauge.
-
Product
High Voltage Porosity Detection
-
High Voltage Technique: The high voltage, or porosity technique, can be used to test coatings up to 25mm (1”) thick and is ideal for inspecting pipelines and other protective coatings. Coatings on concrete can also be tested using this method.
