Pickering Interfaces Inc.
Pickering Interfaces designs and manufactures modular signal switching and simulation for use in electronic test and verification.
- 781 897 1710
- ussales@pickeringtest.com
- 170 Main Street
Unit 108
Tewksbury, Massachusetts 01876
United States of America
-
Product
PXI Very High Density MUX 5 Chan 32 Pole
40-675-002-5/32
Multiplexer Module
The 40-675 series of very high density low cost multiplexer modules are available in a versatile range of switching configurations. The modules are supplied pre-configured in one of six multiplexer modes suitable for signal routing in high channel count ATE and data acquisition systems. The modules use high quality electromechanical signal relays allowing each channel to switch current up to 1A at 150VDC/100VAC. Connections are made via a front panel 200-pin connector.
-
Product
Ethernet/AFDX/BroadR-Reach PCI Fault Insertion Switch - 4 Channel
50-201-004
Fault Insertion Unit
This high bandwidth differential PCI fault insertion card is designed to simulate common faults on high speed two wire communication interfaces such as Ethernet. This card supports 4 or 8-channels of two wire serial connections and can be used for simulating faults on Ethernet, AFDX, Broad R-Reach, 100BaseT and 1000BaseT interfaces. Any wire can be set to an open circuit, shorts can be applied across the wire pair, or to the adjacent pair. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to a supply voltage or ground.
-
Product
PXI Programmable Resistor Module 5x16 Bit, 0 Ohm to 65K Ohm
40-295-021-5/16
Programmable Resistor Module
The 40-295 is a Programmable Resistor module with up to 18 channels of 8-bit resolution resistor chains in a single 3U PXI module. The flexible architecture allows these modules to also be supplied as 12, 16 or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count.
-
Product
PXI 16 Channel Switch Simulation Module
40-480-121
Switch Simulation Module
The 40-480 is designed to simulate the operation of automotive switches where dirty contacts or leaking current can be expected from switch contamination. It allows automotive I/O devices to be tested for correct operation under adverse conditions. The design includes protection circuits that ensure module damage cannot be caused by wiring faults or UUT failures. Each module can support up to 32 channels and is suitable for both 12V and 24V automotive applications.
-
Product
PXI 2.5W Programmable Resistor Module, 8-Channel, 1Ω to 239Ω
40-251-013
Programmable Resistor Module
The 40-251-013 is a programmable resistor module with 8 channels which can be set between 1Ω and 239Ω with 1Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PXI/PXIe RF Multiplexer, Single 8-Channel, 3GHz, 50Ω, SMB
40-874A-001
Multiplexer Module
The 40-874A-001 (PXI) and 42-874A-001 (PXIe) are 50 Ohm 8 to 1 RF multiplexers with 1 bank in a single slot. They have low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss.
-
Product
PXI/PXIe RF Matrix, 16x2, 100 MHz, 75 Ω SMB
42-728A-101
Matrix Switch Module
The 40-728A-101 (PXI) and 42-728A-101 (PXIe) are 16x2 75 Ω RF matrices with SMB connectors. The 4x-727A/728A/729A range are high density RF matrix modules suitable for switching up to 300 MHz in 50 Ω or 100 MHz in 75 Ω. They are available in 50 Ω or 75 Ω versions with SMB connectors or in 50 Ω versions with a multiway connector.
-
Product
High Performance LXI RF & Microwave Multiplexers
Microwave Multiplexer
Our standard microwave multiplexers offer the highest density configurations available, packaging up to 16 SPnT switches into a 2U high rack-mount enclosure. Standard microwave multiplexer systems include 50Ω Versions up to 67 GHz and 75ΩVersions up to 2.5 GHz. Alternatively, you can use our Microwave Switch Design Tool to mount any combination of our wide range of transfer and SPnT relays onto your own front panel design.
-
Product
Modular Breakout System 78-Pin D-type Plugin Module for 40-201
95-201-001
Modular Breakout System
The 95-201-001 Plugin Breakout Module is designed to be fitted to a PXI 40-201 Fault Insertion Switch as part of the Pickering MBoS. The Modular Breakout System is designed to Simplify HILS (Hardware In the Loop Simulation) Applications.
-
Product
LXI HighDensity 224x16 2A Matrix with BIRST
60-554-027
Matrix Switch Module
A high-density single pole matrix module capable of switching up to 300VDC/250VAC, 2A (60W max). The use of high-quality electro-mechanical relays offers high switching confidence for signal routing in large ATE systems.
-
Product
PXI 2-Slot BRIC 24x8 Matrix, 2A 2-Pole (1 sub card)
40-565A-202-24X8
Matrix Switch Module
The 40-565A PXI Matrix BRIC is a range of high-density matrix modules able to switch up to 2 Amps at 150VDC/100VAC They are available in 2, 4 or 8 slot PXI sizes to suit most high-performance PXI Matrix requirements and constructed using quality electro-mechanical relays for high switching confidence.
-
Product
PXI 9 x SPDT RF Switch 1.2GHz 50 SMB Connectors
40-754-109
Switch Module
The 40-754 is a 50Ω High Density RF switch available with 17 or 9 SPDT relays in a single PXI module. The 40-754 is available with two connector options; an SMB connector that provides a frequency range of 1.2GHz (useable to 1.8GHz) occupying two PXI slots, or an MS-M RF multiway connector which limits the bandwidth to 500MHz but offers a high density solution occupying one PXI slot. The RF switch design is identical in each case.
-
Product
PXI 2A Multiplexer, 2-Bank, 16-Channel 4-Pole
40-614-012
Multiplexer Module
The 40-614 High Density 2 Amp multiplexer module is available in 20 configurations. All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 200VDC/140VACThe module is suitable for signal routing in ATE and data acquisition systems. User connections are made via a front panel 160-pin DIN 41612 connector which is fully supported by our range of cabling and connector solutions.
-
Product
PXI/PXIe Microwave Relay, Triple SPDT, 2.5GHz, 75Ω, 1.6/5.6
40-780B-753
Relay
The 40-780B-753 (PXI) and 42-780B-753 (PXIe) are triple SPDT 2.5GHz 75Ω unterminated microwave relay modules. The 40/42-780B range is available with one, two, three or four SPDT switches capable of switching frequencies up to 67GHz in 50Ω or 2.5GHz in 75Ω. Connections are made via front panel mounted high quality RF coaxial connectors, SMA or N-Type for 50Ω and 1.6/5.6 in 75Ω versions.
-
Product
LXI HighDensity 128x16 2A Matrix with BIRST
60-554-024
Matrix Switch Module
A high-density single pole matrix module capable of switching up to 300VDC/250VAC, 2A (60W max). The use of high-quality electro-mechanical relays offers high switching confidence for signal routing in large ATE systems.
Related
-
Virginia Panel Corporation
Virginia Panel Corporation (VPC) provides VPC provides Interconnect Solutions that enable simultaneous connection of multiple test and measurement signal types through one modular interface. Designed to accommodate signal, power, RF, thermocouple, pneumatic/vacuum, and fiber optic connector modules in multiple configurations, VPC’s innovative products meet the demands of test & measurement interconnect requirements.
