Switch Test
Make, break, or change the connection of a circuit.
-
product
Circuit Breaker (Switch) Test Instruments
Wuhan Huatian Electric Power Automation Co., Ltd.
Circuit Breaker (Switch) Test Instruments by HVTEST
-
product
Keysight Quad 1x4 50 Ohm 3 GHz Multiplexer Module for 34980A
34941A
The Keysight 34941A RF multiplexer module for the 34980A Multifunction Switch/Measure Unit offers bi-directional switching for test signals from DC to 3 GHz. High channel isolation ensures quality dynamic range measurements with your oscilloscope, spectrum analyzer, or other instrumentation.
-
product
10 Gb/s SFP/SFP+ Evaluation Board
EV-SFP-171
The purpose of this SFP+ evaluation board is to provide the designer with a convenient means for evaluating SFP+ fiber optic transceiver such as 10 Gb/s(up to 16 Gb/s) SFP/SFP+ transceiver compliant with ANSI Fibre Channel FC‐PI‐5 for high speed electrical and optical specifications. This board provides SMA connectors for high speed TX and RX signals. The low speed control signals such as Tx_Fault, Rx_LOS and Rate_Selects can be controlled by using on board switches and test points. A connector for 2 wire serial interface to the module is also provided.
-
product
Digital Leakage Current Tester
Educated Design & Development, Inc.
Fast - All operator controls are located on the front panel to expedite testing. The entire test can be performed in a matter of seconds! Pays for itself in time and stress savings. Versatile - Measures Leakage Current in accordance with UL, CSA, EN, and IEC/ International Standards. Includes ability to perform open neutral, open ground, and line polarity forward/reverse test conditions. Adaptable - Universal rear panel receptacle allows for testing products with any plug configuration. Accurate - True RMS meter accurately measures both sinusoidal and non-sinusoidal waveshapes. This is important when testing products using a switch mode power supply which can generate non-sinusoidal leakage currents. Calibrated, traceable to NIST. Flexible - A front panel switch permits testing either through the power cord of the product under test, from surface/ patient connection-to-ground, or from surface/ patient connection-to-surface/ patient connection. Portable - Lightweight, with integral handle. Other Features - Product Ground Switching (grounding conductor maintained to device under test when not measuring leakage). Automatic front receptacle disconnect when configured in the 240V test mode (prevents inadvertent connection of 120V when configured for 240V operation). Proven - These are the only leakage current testers designed and supported by Product Safety experts. That is part of the reason why they have become the standard in the industry. Full technical support by experienced safety engineers.
-
product
Physical Layer Switching Systems for copper LAN, WAN, DSL, Telco apps with RJ style connectors.
RJ Series
The RJ Series of computer controlled switching systems are designed for physical layer switching of multiwire signals on RJ style connectors. Since the system uses mechanical relays it acts exactly like a piece of cable which makes it perfect for testing networks without altering the signals or regeneration. These systems are typically used for Ethernet LAN 10BaseT through 1000BaseT, DSL including ASML through GFAST, CAT5 through CAT6A cable testing, USB up to 2.0, RS232, RS422, RS485 up to 8 wire at 20 Mbps and many other applications switched over RJ45 connectors up to 8 wires. They may also be used as lab automation switches, network testing switches, patch panels, network redundancy switches or any number of physical layer applications.
-
product
Handheld Contact Resistance Tester
Weshine Electric Manufacturing Co., Ltd
The hand-held Circuit resistance tester is an innovative product. The product is compact, hand-held operation, battery power supply, easy to carry. The product is mainly used in the measurement of contact resistance and other micro-Euclidean resistance of switch contacts. The test speed is fast and the accuracy is high.
-
product
Benchtop DC Electronic Load
63000
Chroma Systems Solutions, Inc.
The 63000 series programmable DC electronic loads are reliable, precision instruments primarily designed to test switching power supplies, A/D power supplies, power electronic components, adapters, 3C batteries and chargers. Its maximum 350W rated power makes it suitable for testing numerous types of lower power devices.
-
product
200KHz AUTOMATIC TRANSFORMER TEST SYSTEM
VE2729XAU
Its a Microprocessor Based 200KHz Automatic Transformer Tester with inbuilt 20 Pin Channel Scanner for Automatic Switching and Testing Coils & Transformers (Ferrite) with Max. 20 PINS. Test Parameters : -> Inductance (L)-> Leakage Inductance (Lk)-> Capacitance (C)-> DC Resistance (Rdc)-> AC Resistance (Rac)-> Turns Ratio with Winding Polaity-> Quality Factor (Q)-> Impedance (Z)
-
product
L2-7 10GbE Test Solutions
NGY 10GE SFP+ and 10G BASE-T Load Modules
Keysight Network Applications and Security
Ixia's 10 Gigabit Ethernet LSM10GXM test load modules delivers an industry-leading, high-density, affordable layer 2 through 7, 10 Gigabit Ethernet IP test solution. The NGY family supports both low port count layer 2/3 applications with limited project budgets and highest density test lab, QA, and system test applications. NGY is perfect for both converged data center infrastructure testing and 10GbE switch test beds. NGY load modules leverage Ixia's converged data center test applications to offer the high port scalability, virtual scalability, protocol coverage, with an affordable test solution for data communications testing.
-
product
Line Loop Tester
8455
Simpson?s Model 8455 Line Loop tester detects line shorts, opens and multiple ringers, DC voltages and loop resistance. It can measure DC voltage up to 100 volts and loop resistance to 2 megohms. A front panel ?reverse polarity? switch allows changing polarity positions quicker and easier than manually switching test leads when making line checks.
-
product
Vector Signal Generator
SGT100A
The R&S®SGT100A has a clear focus on automated environments with high speed and a compact design. The radio frequency chain has been optimized for the fastest frequency and level switchover times. In the baseband, the multisegment waveform mode helps users quickly switch from one test signal to the next. Though compact in size, the R&S®SGT100A has excellent RF characteristics (signal quality and level accuracy). Maximum output level, level repeatability and excellent EVM performance are key characteristics in production environments. Equipped with a LAN and USB interface, the R&S®SGT100A enables remote control of test equipment in automated applications.
-
product
Test Switches and Accessories
FT Flexitest Family
The ABB FT test kit comes with a convenient carrying case to hold your hand held meter, test plugs patch cords, clips, and test probes in neat order. Patch cords are highly durable and flexible. Test switch accessories include: Test plugs Test kits Covers Interlocking bars Miscellaneous
-
product
Test Switches and Accessories
Test switches are designed and manufactured to allow quick and easy multi-circuit testing of switchboard relays, meters and instruments by any conventional system.These test switches and related test plugs have the features necessary for applications involving the measurement of individual currents and voltages associated with substation instrumentation and protection devices. They have been especially designed for the measurement of potential elements, current elements, and make-before-break short-circuit elements related to Current Transformer (CT) circuits.
-
product
Optical Rackmount Systems
DiCon offers a variety of rack-mountable solutions for fiber optic switching, test automation, and wavelength management. With standardized or customizable options, our platforms can be easily configured to work in different environments. DiCon's systems feature low insertion loss, excellent reliability, and durability. Applications include fiber optic testing and measurement, fiber based sensing, optical network configuration and monitoring.
-
product
Transockets
TESCO Single & Three-Phase Transockets offer the flexibility of a single enclosure for current transformer metering and allow mounting of current transformers and a test switch. By combining the meter socket and transformer cabinet, TESCO provides a cost-effective metering solution.
-
product
Switch Stick Test Equipment
Hanco units provide a full high voltage electrical test as required by OSHA. Front-loading, top-loading and portable units are available.- Sticks can be tested wet or dry.- Test units are available to test sticks up to 14 or 21 feet maximum length or up to 8 feet for the portable unit.
-
product
Coaxial Matrix Switch, DC to 20 GHz
87406B
The Keysight 87406B matrix switch provides the life and reliability required for automated test and measurement, signal monitoring and routing applications. Innovative design and careful process control creates a switch that meets the requirements for highly repeatable switching elements in test instruments and switching interfaces. The switch is designed to operate for more than 10 million cycles and will meet all electrical specifications for at least 5 million cycles. The switch exhibits exceptional insertion loss repeatability. This reduces sources of random errors in the measurement path and improves measurement uncertainty. Switch life is a critical consideration in production test systems, satellite and antenna monitoring systems, and test instrumentation. The longevity of the switch increases system uptime, and lowers the cost of ownership by reducing calibration cycles and switch maintenance.
-
product
HV Switch Tester
HTGK-IV / 392
Wuhan Huatian Electric Power Automation Co., Ltd.
Various indoor and outdoor oil-less, multi-oil switch, vacuum switch, dynamic characteristic test of sulfur hexafluoride switch.
-
product
Multiport Coaxial Switch, DC to 20 GHz, SP4T
87204B
The Keysight 87204B terminated multiport switch provides the life and reliability required for automated test and measurement, signal monitoring and routing applications. Innovative design and careful process control created the Keysight 87204B which meet the requirements for highly repeatable switching elements in test instruments and switching interfaces. The Keysight 87204B is designed to operate for more than 10 million cycles. The exceptional 0.03 dB insertion loss repeatability is warranted for 5 million cycles at 25° C. This reduces sources of random errors in the measurement path and improves measurement uncertainty. Switch life is a critical consideration in production test systems, satellite and antenna monitoring systems, and test instrumentation. The longevity of this switch increases system uptime, and lowers the cost of ownership by reducing calibration cycles and switch maintenance.
-
product
Contacts Resistance Tester
JYK II
•Instrument IPC architecture for domestic production of all models of metal contacts SF6 switchgear, GIS combination of electrical, vacuum switch, oil switch and column switches, contacts and so on.•Sensor: Acceleration speed sensor, rotation speed sensor, linear stroke sensorinstallation is very easy and simple.•Trigger: The trigger, external trigger, the sensor is triggered. Sensor can trigger the circuit breaker manually switching characteristic test, such as a manual column pole division switch.
-
product
Contunuity Tester With Audio Warning
CT-01
Laxtronics Instruments & Controls Pvt. Ltd
5 Kilo Volt AC, 30 Milli Ampere, Timer 0 To 100 Seconds, HV Prods, Start-Stop-Trip-Reset Using Single Switch On The Test Prods. Start Function Apply Test Voltage From 0 To Set Voltage Graduall
-
product
High-Density PXI Large Matrix Modules up to 1 Amp - BRIC
Pickering's high-density PXI large matrix BRICs offer current handling up to 1 Amp and select models are supported by our Diagnostic Test Tools, Built-In-Relay-Self-Test (BIRST) and eBIRST Switching System Test Tools, these tools provide a quick and simple way of finding relay failures within LXI, PCI and PXI switch systems.
-
product
Meter Test Station
WECO 8000
The innovative WECO 8000 Meter Test Station is the first of its kind – a multi-position test board integrating meter qualification and accuracy. This versatile and economic test station is the solution for utilities needing the ability to switch between functional testing and accuracy testing. Separate multi-position test boards are no longer a necessity.
-
product
Keysight Triple 1x2 SPDT Unterminated Microwave Switch Module for 34980A
34947A
The Keysight 34947A microwave switch for the 34980A Multifunction Switch/Measure Unit offers bi-directional switching for test signals from DC to 26.5 GHz. These switches provide excellent insertion loss, isolation, and VSWR specification. The microwave switches are configured as three independent 1x2 (SPDT) unterminated switches on a single module. For general-purpose microwave switching applications, the module can be used to switch separate signal sources for a multi-band receiver/transmitter testing application.
-
product
903 Benchtop Three Phase 40A
Weshine Electric Manufacturing Co., Ltd
1. The instrument has standard four phase voltage and three-phase current output. It can test not only various traditional relays and protection devices, but also various modern microcomputer protections, especially for transformer differential protection and standby automatic switching device. The test is more convenient and perfect.2. Classic Windows XP operation interface, friendly man-machine interface, easy and fast operation; high performance embedded industrial control computer and 8.4 inch resolution 800 × 600 TFT true color display screen, can provide rich and intuitive information, including the current working state of the equipment and various help information.
-
product
7-Pole Test Switch Protectors
6442 & 6442-C
With safety always being a concern while working with electrical boxes, you can depend on TESCO’s Test Switch Protectors (Catalog No. 6442 & 6442-C) to alleviate any uncertainty. This was developed to provide temporary protection of the test switch and to address the rising concern that the terminals of the test switch are exposed while you’re working in the box. The switch protector can prevent incidental contact with live terminals or contact with tools. TESCO’s Test Switch Protectors are constructed of clear, flexible PVC with a voltage rating of 2500V. The switch protector will fit any brand of test switch, regardless of manufacturer, from 4 to 7-pole. TESCO can also develop custom designs of this product to meet unusual test switch configurations.
-
product
High Voltage Breakdown Tester
Model HV-50
Laxtronics Instruments & Controls Pvt. Ltd
5 Kilo Volt AC, 30 Milli Ampere, Timer 0 To 100 Seconds, HV Prods, Start-Stop-Trip-Reset Using Single Switch On The Test Prods. Start Function Apply Test Voltage From 0 To Set Voltage Graduall
-
product
PCI Matrix Cards
PCI Matrix cards are available in the following:*Reed relay based matrices available in 22x4, 22x8, 44x4 or dual 20x4 formats with 1-pole, 2-pole or 1-pole screened relays*2 Amp electro-mechanical relay based 1-pole matrices available in 32x2, 32x4, 16x4, 16x8 or 8x8 formats.*Select modules are supplied with our eBIRST Switching System Test Tools, these tools provide a quick and simple way of finding relay failures within LXI, PCI and PXI switch systems.
-
product
Test & Measurement
Quintech Electronics and Communications Inc.
RF Switches for Testing Wireless Solutions.
-
product
Flight Test Switches
Curtiss-Wright Defense Solutions
Our compact, deterministic flight test switches have been qualified to reliably deliver high-speed, real-time data with a wide temperature operation ranging from -40 to 85°C. Their rapid boot-up capability minimizes data loss from power outages, while their flexible forwarding and filtering configurations can send what is required to multiple destinations for real-time monitoring, recording, and transmission.
