Amplifiers
increase the amplitude of a signal.
See Also: Amp, RF Amplifiers, Preamplifiers, Current Amplifiers, Audio Amplifiers, Voltage Amplifiers, Transconductance Amplifiers, Op Amps, Klystron, Instrumentation Amplifiers, Distribution Amplifiers
-
product
Amplifier Systems Broadband
Systems are complete. They plug into an outlet and are ready to go. Our standard systems are 3U, which is 5.25″ and 5U, 8.75″. Systems are available with or without IEEE-488, RS-232 and Ethernet connectivity. Amplifiers Systems are available in both Broadband and Band-Specific frequencies. We are well-known in the industry for successfully adapting our amplifiers or custom designing new solutions to suit each unique project. Please refer to our Adapted & Custom Design Solutions link to begin formulating your performance objectives and other criteria.
-
product
Peripheral Differential Amplifier
The Peripheral Differential Amplifier (PDA) module allows the simultaneous recording of differential bipolar high-ohmic external voltages, such as reference or pH meters. The PDA has 8 differential input channels, and it is stackable up to units with a total of 64 channels. The PDA module is powered from the grid via an adapter.
-
product
Amplifier
AC-100
The voltage amplifier for connecting piezoelectric acceleration meters, microphones, and other primary voltage output transducers to FFT spectrum analyzers with the IEPE standard current output (ZET 017-U2, ZET 017-U8, A19-U2).
-
product
1-Channel 3.6 GHz or 2-Channel 1.8 GHz 12-bit A/D with DDC - 6U VPX
Model 57741
- Supports Xilinx Virtex-7 VXT FPGAs- GateXpress supports dynamic FPGA reconfiguration across PCIe- One or two 1-channel mode with 3.6 GHz, 12-bit A/Ds- Two or four 2-channel mode with 1.8 GHz, 12-bit A/Ds- Programmable one- or twochannel DDCs (Digital Downconverters)- 4 or 8 GB of DDR3 SDRAM- µSync clock/sync bus for multiboard synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x8- Optional user-configurable gigabit serial interface-Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Ruggedized and conductioncooled versions available- Supports GateXpress® FPGA-PCIe Configuration Manager- Synchronize up to twelve modules with Model 9192 System Synchronization and Distribution Amplifier- 1U Rack-mount
-
product
Motion Control Terminal Board for Panasonic MINAS A4 Servo Amplifiers
DIN-814P-A40
This well-designed motion control terminal board is for the users who use Panasonic MINAS A4 super servo. With this terminal board, users can ealisy complete wiring with PCI-8174, PCI-8164, PCI-8154, PCI-8158 and PCI-8134.
-
product
General Purpose Op Amplifiers
When your design requires general purpose op amps, Analog Devices broad portfolio of high speed op amps, precision op amps, and instrumentation amplifiers deliver the unmatched performance and exceptional value that you’re looking for. Explore our selection of op amps by your necessary parameters and find expert, system-level advice to address your design issues by consulting with ADI resources such as EngineerZone.
-
product
Panel-mounted HIL Power Amplifier
PAC60Ci
PAC60Ci is the six-phase real time simulation amplifier, with maximum RMS phase current of 30A and maximum output power of 450VA. This current amplifier is possessed of high accuracy and fast liner response.
-
product
Panel-mounted Power Amplifier For Network Simulators
PAV250Bi
PAV250Bi is one of the conventional voltage power amplifier model, which is specially designed for R&D of power system simulation.
-
-
product
4-Ch 1.25 GHz, 16-bit D/A with DUC, Extended Interpolation, Virtex-6 - XMC
Model 71671
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Four 1.25 GHz 16-bit D/As- Four digital upconverters- Extended interpolation range from 2x to 1,048,576x- Programmable output levels- 250 MHz max. output bandwidth- 2 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- Dual uSync clock/sync bus for multimodule synchronization- PCI Express (Gen. 1 & 2) interface, up to x8- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Synchronize up to four modules with Model 7192 System Synchronization and Distribution Amplifier - PMC/XMC- Synchronize up to twelve modules with Model 9192 System Synchronization and Distribution Amplifier- 1U Rack-mount
-
product
Panel-mounted Power Amplifier(Hardware In The Loop Simulation)
PA30Bi
PA30Bi is the panel-mounted type real time simulation amplifier with three-phase current and four-phase voltage.
-
product
High Speed High Voltage Amplifier
WMA-300
The WMA-300 is a high voltage, wide bandwidth laboratory amplifier. Its high output voltage, current and wide bandwidth have been designed to serve the needs of a wide variety of high-tech experiments. The WMA-300 can be used for MEMS actuation, EO-modulators, PZT (piezo) positioners, ultrasonics, and many other applications. Two WMA-300 amplifiers and a WMA-IB-HS phase inverter - buffer can be used to double the output voltage.
-
product
Low Voltage DC / Battery Powered HV Amplifiers
WMA-01 And WMA-01LF
The Falco Systems WMA-01 is a high voltage amplifier that runs from an 24 - 30V DC power supply and can be battery powered if required, e.g. for use in a Faraday cage. Its internal high voltage generator is inductor-free and hence does not spread magnetic interference in sensitive experimental setups. The output noise is impressively low at 3mVrms. For extremely low noise applications where bandwidth is not an issue, a dedicated WMA-01LF version is available that contains an output low pass filter capacitor which reduces the bandwidth to 50Hz, but makes the noise drop to below 0.1mVrms. This bandwidth-limited amplifier is ideal for MEMS or piezo positioning with manual voltage adjustment.
-
product
High voltage amplifiers (to ±500V)
These amplifiers provide high amplitudes and bandwidths, and are well suited for use as booster amplifiers for lower-voltage arbitrary waveform generators.
-
product
Amplifier Products
In addition to the options for input and output interfaces and package style, QuinStar also offers a wide range of useful options, added features and practical configurations to suit customers’ specific requirements. These optional features may be incorporated in most of the amplifier products offered by QuinStar Technology. If desired, more than one option may be selected for some amplifiers.
-
product
Operational Amplifier
Op Amp Series
The amplifier is capable of operating at supply voltages from 0.9V to 3V with specified specs at 1V and 1.8V single supply.The input common mode range extends to both power supply rails without the offset glitch and input bias current phase reversal inherent to most rail to rail input amplifiers.
-
product
L-Band RF Tuner and 2-Channel 200 MHz A/D with Virtex-6 FPGA - 3U VPX
Model 52690
- Accepts RF Signals from 925 to 2175 MHz- Programmable LNA boosts LNB (low noise block) antenna signal levels with up to 60 dB gain- Programmable analog downconverter provides I + Q baseband signals with bandwidths ranging from 4 to 40 MHz- Two 200 MHz 16-bit A/Ds- Supports Xilinx Virtex-6 LXT and SXT FPGA- 2 GB DDR3 SDRAM or 32 MB of QDRII+ SRAM- Sample clock synchronization to an external system reference- Clock/sync bus for multiboard synchronization- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- 3U VPX form factor provides a compact, rugged platform- Compatible with several VITA standards including: VITA-46, VITA-48 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
product
Limiting Amplifiers
RF limiting amplifier PE15A6002 is rated at -40 dBm minimum power input and 10 maximum power input. Our limiting radio frequency amp is part of over 40,000 RF, microwave and millimeter wave components available from Pasternack. This coaxial limiting amplifier can ship worldwide the same day of the purchase as with our other available RF parts.
-
product
NI STS
RF Test and Measurement Solutions, LLC
RFTMS is a leader in configuring systems to meet your needs, as well as designing load board, writing SW, and integrating the final solution. We do this for wafer test, packaged parts, and modules. RFTMS can address any level of integration that your parts employ, from a single functional block, i.e., Power Amplifier (PA) to System-on-a-Chip (SOIC). We test all sorts of RFICs.
-
product
Stand Alone/ Bench Top Load Cell Amplifier/ Conditioner Module
MODEL TMO-2
The TMO-2 Transducer Modules is a complete differential amplifier/signal conditioners with self contained power. The units provide excitation, balance and span adjustment via precision 10 turn pots, and shunt calibration necessary to couple a user supplied bridge type transducer to an indicating instrument. Full scale output is specified at plus or minus 10 VDC. The TMO-2 provides a floating shunt calibration circuit which applies calibration at the transducer, thereby eliminating errors due to line losses. The excitation supply incorporates a Wagner Ground to greatly improve Common Mode Rejection. The factory set bandwidth of the module is narrow to improve stability for applications such as weighing scales. The removal of a single capacitor will increase the frequency response DC to 60K Hz for dynamic data applications.
-
product
3-Ch 200 MHz A/D with DDC & 2-Ch 800 MHz D/A with DUC, Kintex UltraScale - 6UVPX
Model 57821
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Complete radar and software radio interface solution- Supports Xilinx Kintex UltraScale FPGAs- Three 200 MHz 16-bit A/Ds- Three multiband DDCs (digital downconverters)- One DUC (digital upconverter)- Two 800 MHz 16-bit D/As- 5 GB of DDR4 SDRAM- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multimodule synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x8- Optional LVDS and gigabit serial connections to the FPGA for custom I/O- Compatible with several VITA standards including: VITA-46, VITA-48 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
product
Video Signal Distributor
MSHM-305A/310A
MSHM-305A/310A, HDMI Distribution,Amplifier, distribute three digital video input sources to the five (or ten) output channels. The built in amplification function enables HDMI signal distribution without signal loss. The product guarantees to support full channels HDMI/HDCP compliance. User can select one input source of the three and make sure connected condition with led of the front panel.
-
product
Bridge Amplifier
90376
This miniature, on-board, transducer amplifier is capable of supplying excitation voltage and amplifying millivolt signals from strain gage based transducers.
-
product
Amplifiers
Gigacom supplies custom amplifiers to several Test Ranges to support on going test programs. We have experience designing solid state amplifiers operating at power levels up to 1KW and from HF to X-Band.
-
product
Fiber Optic Sensor & Amplifier
FG-1300 | FS-5500/FS-540
The FG-1300 is a non-contact type high-performance amplifier that emits red light from LED to a rotating object, and detects the variation of the reflected red light amount.This amplifier is used in combination with an exclusive detector FS-5500*/FS-540 Fiber Optic Sensors which has adopted environment resistant design. The glass fibers are covered with flexible stainless steel tube for rotation measurement in limited space.
-
product
1 GHz A/D and D/A with Virtex-6 FPGA - 3U VPX
Model 52630
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Supports gigabit serial fabrics including PCI Express, Serial RapidIO and Xilinx Aurora- One GHz 12-bit A/D- One GHz 16-bit D/A- Up to 2 GB of DDR3 SDRAM or 32 MB of QDRII+ SRAM- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multiboard synchronization- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- 3U VPX form factors provides a compact, rugged platform- Compatible with several VITA standards including: VITA-46, VITA-48 AND VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- Synchronize up to twelve modules with Model 9192 System Synchronization and Distribution Amplifier- 1U Rack-mount
-
product
High Voltage, High Current Linear Amplifier
P100
The P100 is a general purpose linear amplifier having a fixed amplification of 10 times and capable of bipolar high voltage output of ±50V. Any functiongenerator or arbitrary waveform generatoror any othe signal source with amplitude up to ±10 V can be used as an input device.
-
product
Linear Amplifiers
Advanced Science and Novel Technology, Co., Inc.
Broadband (DC-12GHz) linear amplifier for receiver-side applicationsFeatures controlled gain from 0dB to 31.5dBFeatures input offset adjustment and input peak detectorFully differential input interface with on-chip 50Ohm terminationFully differential output interface with on-chip 50Ohm terminationOutput 1dB compression point of 1.5dBm3rd Harmonic better than -47dBc within the full bandwidth15dB Noise FigureSingle +3.3V or -3.3V power supplyPower Consuption: 530mW typicalFabricated in SiGe for high performance, yield, and reliabilityCustom CQFP 24-pin package
-
-
product
4-Ch 500 MHz A/D with DDC & 4-Ch 800 MHz D/A with DUC, Virtex-7 FPGA - 6U VPX
Model 58751
- Supports Xilinx Virtex-7 VXT FPGAs- GateXpress supports dynamic FPGA reconfiguration across PCIe- Two or four 500 MHz 12-bit A/Ds- Two or four multiband DDCs (digital downconverters)- One or two DUCs (digital upconverters)- Two or four 800 MHz 16-bit D/As- 4 or 8 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- PCI Express (Gen. 1, 2 & 3) interface up to x8- LVPECL clock/sync bus for multiboard synchronization- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Optional 400 MHz 14-bit A/Ds- Ruggedized and conduction-cooled versions available- Supports GateXpress® FPGA-PCIe Configuration Manager- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
