Amplifiers
increase the amplitude of a signal.
See Also: Amp, RF Amplifiers, Preamplifiers, Current Amplifiers, Audio Amplifiers, Voltage Amplifiers, Transconductance Amplifiers, Op Amps, Klystron, Instrumentation Amplifiers, Distribution Amplifiers
-
Product
Optometers, Amplifiers, Display Meters
-
Optometers are a specific type of digital multimeter (DMM) used for optical radiation measurements. The particular light detector(s) connected determine the wavelength range/spectral weighting function and displayed measurement units.
-
Product
Low Voltage DC / Battery Powered High Voltage Amplifiers
WMA-005 And WMA-005LF
-
The Falco Systems WMA-005 is a high voltage amplifier that runs from an 24 - 30V DC power supply and can be battery powered if required, e.g. for use in a Faraday cage. Its internal high voltage generator is inductor-free and hence does not spread magnetic interference in sensitive experimental setups. The output noise is impressively low at 3mVrms. For extremely low noise applications where bandwidth is not an issue, a dedicated WMA-005LF version is available that contains an output low pass filter capacitor which reduces the bandwidth to 50Hz, but makes the noise drop to below 0.1mVrms. This bandwidth-limited amplifier is ideal for MEMS or piezo positioning with manual voltage adjustment.
-
Product
Ka Band Power Amplifier
-
The ERZ-HPA-2000-4500-24 is a Ka Band Amplifier providing an output power of 24 and a gain of 22 dB. The compact size and modularity makes it ideal for a wide range of applications. Frequency Range (GHz): 20,00 to 45,00.
-
Product
Femtosecond Optical Parametric Amplifier
CDP 2017
-
*> 30% conversion efficiency from pump pulse to parametric radiation*Wavelength conversion for ExciPro, TAPPIR, FOG 100-DA*Wavelength conversion options for wavelength tuning from 240 nm to 16 mm
-
Product
Power Sensors
RTP5518
-
Providing the highest video bandwidth and fastest rise times, the 50 MHz to 18 GHz Power Sensor by Boonton is the ideal instrument for fast, accurate and reliable RF power measurements. This module is ideal for many different applications including Crest Factor and Peak to Average Power Ratio (PAPR) measurements for Power Amplifiers and RF components; Telecommunication & Satellite signals: W-CDMA, QAM, OFDM, LTE-FDD and LTE-TDD; WiFi signals: 802.11ac and legacy 802.11 a/g/n/b; RF and Microwave pulse modulated power measurements: RADAR, MRI, Particle Accelerators; General purpose scalar measurements such as gain and return loss using modulated and pulsed signals as well as CW; and Monitoring, Recording, ALC loops, transient phenomena.
-
Product
4-Ch 1.25 GHz, 16-bit D/A with DUC, Extended Interpolation, Virtex-6 - 6U VPX
Model 57671
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Four 1.25 GHz 16-bit D/As- Four digital upconverters- Extended interpolation range from 2x to 1,048,576x- Programmable output levels- 250 MHz max. output bandwidth- 2 GB of DDR3 SDRAM- PCI Express (Gen. 1 & 2) interface up to x8- Sample clock synchronization to an external system reference- Dual µSync clock/sync bus for multiboard synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Synchronize up to twelve modules with Model 9192 System Synchronization and Distribution Amplifier- 1U Rack-mount
-
Product
900 MHz Trunk Hybrid Amplifier
AS 1111
-
Hybrid Amplifier used in trunk and branch lines specially designed to serve the need of cable systems with long trunk cables. They incorporate Good Quality Hybrid IC Module to obtain better features.- Frequency Range: 40 ~ 900 MHz- Output Level: 102 dBµV- Separate IN & OUT Fuses- Level Flatness: ±0.75 dB- 32 dB Gain (40 dB Optional)- Incorporates Good Quality- Hybrid IC Module- Hybrid IC Protected
-
Product
Single Channel High Voltage Linear Amplifier
A800
-
The A800 is a general purpose broadband linear amplifier having a fixed amplification of 100 times and capable of bipolar high voltage output of ±400V. Any functiongenerator or arbitrary waveform generatoror any othe signal source with amplitude up to ±4 V can be used as an input device. The amplifier's output is linear from DC up to megahertz range. It can be used in a wide range of applications, for example to drive piezo actuators, MEMS, OLEDs, liquid crystals, etc.
-
Product
Amplifiers
-
The amplifier is one of the most important components in a pulse processing system for applications in counting, timing, or pulse amplitude (energy) spectroscopy, providing the pulse-shaping controls needed to optimize the performance of the analog electronics.
-
Product
External Pre-amplifiers
-
Although all Spectrum A/D cards have a very powerful input section with a highly configurable input amplifier and a variety of input ranges it is sometimes necessary to have additional external amplifiers if the signal to acquire has an extremely low level. Spectrum offers a range of perfectly matching external amplifiers to cover such cases. These powerful amplifiers have been rated using the Spectrum cards and offer best performance together with high amplification rates.The amplifiers are simply connected between the signal source and the Spectrum A/D card input and can be manually switched between different settings using small lever keys. All amplifiers allow the offset compensation by using an adjustable screw.
-
Product
8-Channel 200 MHz A/D with DDC, Virtex-6 FPGA - 6U VPX
Model 58661
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Eight 200 MHz 16-bit A/Ds- Eight multiband DDCs (digital downconverters)- Two multiboard programmable beamformers- Up to 4 GB of DDR3 SDRAM; or: 64 MB of QDRII+ SRAM- PCI Express (Gen. 1 & 2) interface up to x8- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multiboard synchronization- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
1 GHz A/D and D/A with Virtex-6 FPGA - 6U VPX
Model 57630
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- One 1 GHz 12-bit A/D- One 1 GHz 16-bit D/A- Up to 2 GB of DDR3 SDRAM; or: 32 MB of QDRII+ SRAM- PCI Express (Gen. 1 & 2) interface up to x8- Sample clock synchronization to an external system reference- Dual-µSync clock/sync bus for multiboard synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Synchronize up to twelve modules with Model 9192 System Synchronization and Distribution Amplifier- 1U Rack-mount
-
Product
Class-D Audio Amplifiers
-
Analog Devices is a leader in Class-D audio amplifiers and audio signal processing, and we deliver audiophile-level performance with our proven analog and digital technology. We offer a wide range of audio amplifiers, including industry-leading microphone preamps, microphone drivers, line drivers, and receivers. Our Class-D amplifiers, in particular, are among the lowest power and lowest distortion in the industry. Our portfolio includes Class-A, Class-B, and Class-D audio amplifier offerings, along with a breadth of power ICs. Analog Devices amplifier products have been used in many high volume consumer products where the highest audio quality is expected. The lowest power consumption also enables this performance in many battery powered applications as well.
-
-
Product
Software
TOELLNER-wavecontrol
-
Toellner Electronic Instrumente GmbH
The Software TOELLNER-WaveControl provides waveforms and controls the TOELLNER system components at the test station, which can be individually tailored to your requirements. Using a DAQ-Card, any signal waveform can be provided with Arbitrary Power Supplies or 4-Quadrant Amplifiers with outputs from 160 W to 5200 W. For fast interruptions, TOELLNER offers electronic switches with switching times below 500 ns.
-
Product
Panel-mounted Voltage Power Amplifier
PAV120Bi
-
PAV120Bi is specially designed for R&D of power system simulation. It is adapt to various capacitive and inductive load. It is with 6 channels voltage outputs, each channel with 120V/60VA maximum output.
-
Product
High-Voltage Amplifier
ZET 420
-
The high-voltage signal amplifier for emission of acoustic signals through capacitive emitters: sonic detectors (without integrated amplifiers), piezoelectric emitters, and transducers.
-
Product
SWITCHABLE FILTER BANKS
AFS-12WB
-
Matrix Test Equipment Incorporated
Models AFS-12WB contain banks of Matrix Model FLT-1 filters. Each filter may be individually selected. The Model AFS-12WB retains the manual operation in addition to remote control through the GPIB IEEE-488 interface. Optional internal Post Amplifier PA-20-20 with a gain of 0, 17 and 32dB @ +5dBm max..
-
Product
RF Amplifier
SA812C
-
Hangzhou Softel Optic Co., Ltd.
SA812C1/SA812C2 Field Bidirectional AGC Amplifier is a new high gain amplifier. Adopt optimized circuit design and scientific and rational process. High performance AGC control circuit inside is useful for stable gain and low distortion. It's the best choice for large and medium-sized bidirectional CATV transmission network.
-
Product
CATV Amplifiers
-
Electronic devices that boost weak TV and broadband signals (audio, video, data) traveling through coaxial cables, compensating for signal loss from splitters, long cable runs, or network nodes to maintain strong, clear picture/data quality for multiple devices, operating across specific frequency bands for both forward (downstream) and reverse (upstream) paths.
-
Product
Preamplifier, 10 MHz to 4 GHz
87405B
Amplifier
Preamplifiers and System Noise Figure Application Note This note discusses noise figure basics including applications and characteristics of Keysight simplifier technology. Highlighted are Keysight's 87405C portable preamplifiers that provide an exceptional gain of 25 dB up to 18 GHz and a probe-power bias connection which eliminates the need for an additional DC power supply. Read the Preamplifiers and System Noise Figure Application Note now!
-
Product
USB Preamplifier, 2 to 50 GHz
U7227F
Amplifier
The U7227F, 2 to 50 GHz USB preamplifier is designed to bring reliable gain and low noise figure to measurement systems improving the overall system performance and reduce systematic errors; a total solution to the X-Series signal analyzers to perform noise figure measurement
-
Product
Ultra Low Level DC Voltage Amplifiers
-
The EM A10 is a low level amplifier module for sensitive measurements, data collection and systems, where signals below 1 nanovolt may be measured. It is ideal for the input unit for precision voltage measuring systems, requiring voltage sensitivity for measuring low noise and low impedance sources. The noise level of the A10 is equivalent to a perfect resistor of about 20 ohms. When used with a digital voltmeter, steady one nanovolt digits may be displayed, with a response time constant of less than a second. The input voltage stability of the A10 is very high, with the drift around a nanovolt per degree C. The input connectors are made from pure copper. The input impedance is very high, and is time dependent, determined by the loop gain.
-
Product
Components - Power Amplifiers (FPA)
FPA Series
-
FPA series driver amplifiers and power amplifiers are discrete and/or MMIC pHEMT device-based amplifiers that operate over the frequency range 18 to 110 GHz for high output power applications. The amplifiers are offered in two categories, standard and custom built up to 250 GHz.The custom-built amplifiers are offered in various RF interfaces, including standard waveguide or coaxial connectors, for convenient system integration. The optional input and output integrated isolators are available to further improve the port return loss.
-
Product
JFET Input Amplifiers
-
Analog Devices JFET input op amps or FastFET high speed (>50 MHz) input op amps provide high input impedance and ultralow input bias currents for high speed applications. The majority of our FET input op amps feature wide supply ranges from +5 V to 12 V or higher and feature rail-to-rail outputs enabling wide dynamic range.
-
Product
USB Preamplifier, 10 MHz to 4 GHz
U7227A
Amplifier
The U7227A, 10 MHz to 4 GHz USB preamplifier is designed to bring reliable gain and low noise figure to measurement systems improving the overall system performance and reduce systematic errors; a total solution to the X-Series signal analyzers to perform noise figure measurements.
-
Product
Shunt Isolation Amplifier
-
Knick Elektronische Messgeräte GmbH & Co. KG.
Especially to accurately measure large DC currents via shunt resistors, ie for making isolated detection of mV voltage on shunts. Variants with calibrated range selection. Working voltage up to 3600 V AC / DC.
-
Product
Communications/Data Link Amplifiers
-
Amplifiers specific to the Communications systems include a wide range of Solid State Power Amplifiers (SSPAs) and Low Noise Amplifiers (LNAs) originally from Paradise Datacom and a range of organically developed products within TMS. Satcom SSPAs are considered a core competence of Paradise Datacom's product line who have invested heavily in converting it's complete amplifier offering from GaAs to GaN from C-Band all the way to Ka-Band.
-
Product
USB Preamplifier, 100 MHz to 26.5 GHz
U7227C
Amplifier
The U7227C, 100 MHz to 26.5 GHz USB preamplifier is designed to bring reliable gain and low noise figure to measurement systems improving the overall system performance and reduce systematic errors; a total solution to the X-Series signal analyzers to perform noise figure measurement
-
Product
Four Quadrant Power Amplifier
PAV3000
-
PAV Series Four-quadrant Simulation Power Amplifier based on linear power amplifier technology and integrated advanced technical performance and rich functions.
