RF Attenuators
Used to reduce input RF & Microwave power by a fixed ratio – expressed in dB. (www.e-meca.com)
-
Product
PXI/PXIe RF Switch, Hex SPDT, 3GHz, 75Ω, SMB
42-830A-006
Switch Module
The 40-830A-006 (PXI) and 42-830A-006 (PXIe) are 75Ω RF switches with 6 separate SPDT relays in a single slot. They have been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. The switch banks have been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss.
-
Product
Solid State RF and Microwave Switches
-
The Solid State RF and Microwave Switches have the following advantages over mechanical switches; long operating life, fast switching time, low power consumption and small size. Mechanical RF and Microwave Switches usually have lower insertion loss, higher isolation and higher RF power handling capability. However, because of the advantages mentioned above, Solid State RF and Microwave Switches are to prefer if very low insertion loss and/or very high isolation is not needed.
-
Product
Manual Attenuator (Waveguide)
-
RF Lambda’s manual waveguide attenuators are used to control signal levels using a manual control knob. These are commonly used in test setups or systems where an operator is present and there is a need to change signal levels manually.
-
Product
RF Power Splitter, Combiner, Divider RoHS, 8 Way, Type-N Female, 350 - 1000 MHz, 50 Ohm
PD2380
-
INSTOCK Wireless Components, Inc
Wideband Frequency (350 - 1000 MHz)Low Insertion Loss (0.4 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.2 : 1 avg)RoHS Compliant Splitter ConstructionTri Alloy Type N Female (Jack) Low PIM
-
Product
PXIe-5654, 250 kHz to 20 GHz, PXI RF Analog Signal Generator
784776-01
Signal Module
PXIe, 250 kHz to 20 GHz, PXI RF Analog Signal Generator - The PXIe-5654 features a combination of exceptional phase noise and frequency tuning time. These features address applications such as blocker test/receiver desensitization, high-performance intermodulation distortion measurements, and various electronic warfare applications. The PXIe-5654 is designed to meet the challenging requirements of RFIC characterization, satellite test, and radar applications. Some PXIe-5654 options include a PXIe-5696 Amplitude Extender Module. The PXIe-5696 supports a frequency range of 250 kHz to 20 GHz and an extended amplitude range up to 27 dBm.
-
Product
PXI Single 4 to 1 RF Multiplexer 2GHz 50 Ohm SMA Terminated
40-740-521
Multiplexer Module
40-740, 40-745 and 40-746 RF Multiplexers are a range of Bi-Directional Multiplexers with bandwidth up to 2000MHz. They are arranged as Single 8 to 1, Dual 4 to 1 or Single 4 to 1 configurations, all with excellent Insertion Loss, VSWR and Isolation, in 50 Ohm or 75 Ohm versions with a wide choice of connectors.
-
Product
PXI/PXIe RF Switch, Triple SPDT, 3GHz, 75Ω, SMB
40-830A-003
Relay
The 40-830A-003 (PXI) and 42-830A-003 (PXIe) are 75Ω RF switches with 3 separate SPDT relays in a single slot. They have been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. The switch banks have been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss.
-
Product
Coaxial Fixed Attenuator, DC to 18 GHz
8491B
Attenuator
The Keysight 8491B coaxial fixed attenuator provides precision attenuation, flat frequency response and low SWR over broad frequency ranges. The attenuator is available in nominal attenuations of 3 dB and 6 dB, as well as 10 dB increments from 10 dB to 60 dB. It has type-N connectors with a maximum frequency of 18 GHz. This attenuator is swept-frequency tested to ensure specification compliance at all frequencies. Calibration points are provided on a nameplate chart attached to each unit.
-
Product
RF Front-end
-
The RF integrated passive device (RF IPD) uses a high-resistivity substrate to integrate quality factor components such as capacitors and indictors. Many functions like impedance matching networks, harmonic filters, couplers, baluns, and power combiners/splitters can be designed using IPD technology. ST's IPDs are manufactured using thick film and HiRes Si or glass wafer manufacturing technology and photolithography processing.
-
Product
RF Bridge, 50 Ohm, 300 kHz to 3 GHz
86205B
-
The Keysight 86205B high directivity 50 ohm RF bridge offers unparalleled performance in a variety of general-purpose applications. It is ideal for accurate reflection measurements and signal leveling applications.
-
Product
RealProbe RF Probes
-
Unmatched performance In-Circuit RF Probes covering up to 18GHz. These are must tools for any in-circuit RF and Microwave testing and troubleshooting.
-
Product
PXI/PXIe RF Multiplexer, Dual 4-Channel, Terminated Common, 3GHz, 50Ω, SMB
40-876A-002
Multiplexer Module
The 40-876A-002 (PXI) and 42-876A-002 (PXIe) are 50 Ohm 4 to 1 RF multiplexers with 2 banks in a single slot. Additionally, extra switching allows the common connection to be terminated into 50 Ohm, maintaining signal integrity. The module has low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss.
-
Product
Advanced Reconfigurable Modular OTA RF Test Enclosures, ≥100 DB Isolation, 300 MHz - 90 GHz
dbSAFE ARMOR
-
The dbSAFE ARMOR series of shielded boxes are cost-effective solutions for OTA testing in the mmWave spectrum. Providing a shielded, fully anechoic test environment, these RF test enclosures ensure stable and repeatable measurements over a wide frequency range (from 300 MHz to 90 GHz).
-
Product
PXI/PXIe RF Multiplexer, Single 8-Channel, 3GHz, 50Ω, MCX
42-874A-101
Multiplexer Module
The 40-874A-101 (PXI) and 42-874A-101 (PXIe) are 50 Ohm 8 to 1 RF multiplexers with 1 bank in a single slot. They have low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss.
-
Product
PXI 8x9 RF Matrix 250MHz 75 SMB
40-725-751
Matrix Switch Module
The 40-725 is an 8x9 RF Matrix Module suitable for switching frequencies up to 500MHz (50Ω version). The 40-725 is available in either 50Ω or 75Ω versions with SMB coaxial connectors. It is intended for the easy construction of high performance bidirectional matrix switching systems. Automatic Isolation Switches are located on all coaxial connections, these disconnect the matrix from the external test fixture maximizing isolation and RF performance.
-
Product
RF Power Splitter, Combiner, Divider RoHS, 6 Way, Type-N Female, 698 - 2700 MHz, 50 Ohm
PD2060
-
INSTOCK Wireless Components, Inc
Wideband Frequency (698 - 2700 MHz)Low Insertion Loss (0.5 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.15 : 1 avg)RoHS Compliant Splitter ConstructionTri Alloy Type N Female (Jack) Low PIM
-
Product
USB/Ethernet Control Step Attenuator
-
RF Lambda’s USB / ethernet control step attenuators utilize the same RF core as our standard digital attenuators only they incorporate a USB / ethernet controller to allow users to easily setup the control from any PC or network.
-
Product
PXI/PXIe RF Multiplexer, Single 16-Channel, Terminated, 8GHz, 50Ω, SMA
42-883B-002
Multiplexer Module
The 40-883B-002 (PXI) and 42-883B-002 (PXIe) are single 16 to 1 50Ω RF multiplexers with 8GHz bandwidth and automatic termination of unused signal channels. They are available in 8 to 1 and 16 to 1 configurations in two and three slots respectively.
-
Product
RF Power Monitors
-
Standard connectors: RF In / Out - N-Female, UHF optional. Sampling Ports - RCA-Female, BNC optional.
-
Product
75 Ohm Mini SMB to 1.0/2.3 Adaptor Assembly
40-978-731-0.25m
RF Cable Assembly
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
Product
PXIe-5644, 6 GHz, 80 MHz Bandwidth, RF PXI Vector Signal Transceiver
782376-01
Vector Signal Transceiver
6 GHz, 80 MHz Bandwidth, RF PXI Vector Signal Transceiver—The PXIe‑5644 combines a vector signal generator and vector signal analyzer with FPGA-based real-time signal processing and control into a single device, also known as a VST. Because of this software-designed approach, the PXIe‑5644 features the flexibility of a software defined radio architecture with RF instrument class performance.
-
Product
PXI 8x4 RF Matrix 300MHz 50 SMB
40-729-001
Matrix Switch Module
40-727/728/729 are RF Matrix Modules suitable for switching frequencies to 300MHz (50Ω version). The modules are available in either 50Ω or 75Ω versions with a choice of coaxial connectors. The 40-727/728/729 are designed designed to provide a simple and scalable bidirectional matrix to RF frequencies. They are intended for the easy construction of high performance bidirectional matrix switching systems.
-
Product
PXI-5650, 1.3 GHz RF Signal Generator
779670-00
RF Signal Generator
The PXI‑5650 features continuous-wave generation capabilities with FM, 2‑FSK, or OOK modulation. It uses direct digital synthesis (DDS) for high-resolution frequency hopping or phase-continuous sweeping for fixture and device characterization applications. The PXI‑5650 is ideal for clocking nonstandard sample rates, such as WCDMA signals at baseband or intermediate frequency (IF). With these versatile signal generators, you can perform analog and digital modulation through the onboard DDS circuit, which gives you frequency modulation and frequency-shift keying for applications such as bit error rate test, antenna testing, or even keyless entry. You can also perform amplitude modulation using on-off keying.
-
Product
Elite™ 13.56 MHz RF Plasma Generators
-
The elite™ Series of RF plasma generators provides state-of-the art technology in a compact air-cooled package. The elite is designed with high speed closed loop control, a class E RF deck and a switching modulator for superior output performance. The elite design utilizes a single printed circuit board assembly for the full rack product virtually eliminating all internal wires and connectors and thereby providing the highest reliability available.
-
Product
PXI/PXIe RF Matrix, 16x8, 300 MHz, 50 Ω, SMB
40-724-011
Matrix Switch Module
The 40-724-011 (PXI) and 42-724-011 (PXIe) are 16x8 RF matrix modules suitable for switching frequencies up to 300MHz. Having a 50 Ω characteristic impedance and front panel SMB connectors, these modules provide a simple and scalable bidirectional matrix for RF and are intended for the easy construction of high performance switching systems.
-
Product
CATV RF Optical Receiver
L-RF-MN-RX
-
The QuestTel''s L-RF-MN-RX module optical receivers are versatile, low-cost and compact optical receivers for use in HFC fiber applications. It is perfect solution for the transport and distribution of CATV RF signals over fiber optic cable. The L-RF-MN-RX module housed in a small housing and have adjustable RF output level. May be used as a hand held device for testing, or placed at a customers premise for the reception of cable television services. The Receiver is designed to operate with a very low optical input level between the range of +3dBm to -12dBm.
-
Product
Wireless & RF Testing
-
MET Laboratories is a widely respected wireless testing lab, with East coast, West coast, and Central operations. Here are some of our wireless capabilities and accreditations assisting with the homologation needs of the wireless manufacturer:
-
Product
CP400X, 400 MHz, ±60 V, 10X Attenuation, Single-Ended Passive Oscilloscope Probe
784254-01
High Current Probe
The CP400X is a coaxial passive probe with fixed 10X attenuation for oscilloscopes that provide 1 MΩ input impedance. It is 2 meters in length. The CP400X attaches to BNC connections on both the signal input and instrument sides.
-
Product
PCI 8x9 RF Coaxial Matrix Card 50Ω SMB
50-725A-511
Matrix Switch Module
The 50-725A is an 8x9 RF Matrix Module suitable for switching frequencies up to 500MHz. The 50-725A is available in either 50Ω or 75Ω versions with SMB coaxial connectors. It is intended for the easy construction of high performance bidirectional matrix switching systems.
-
Product
Analog Receiver / RF Tuners
-
The Bandit™ family of analog receivers or RF tuners provide a series of high-performance, stand-alone RF downconverter modules. These products offer a low noise figure, programmable gain and a high dynamic range and ensure there are no gaps in the RF spectrum coverage.
