Shielded Box
a space surrounded by an electromagnetic radiation barrier
See Also: Boxes, Faraday Cages, Decade Box, Anechoic Boxes, Black Box, Breakout Boxes, Hot Box, White Box, RF Box, Programmable Resistance Box
-
Product
Cable Test Box
-
Cables are a critical part of any sensor measurement system and damaged cables cause frequent delays during test setup. PCB has developed a relatively simple device to test cables on a channel by channel basis for BNC, 10-32, and 5-44 coaxial connectors. Simply connect both ends of the cable and faults will be indicated for shield failure, conductor failure, or short circuit shield to conductor. Power is provided by a single, replaceable 9 volt battery.
-
Product
Break In Break Out Box
MS 3648I
-
Break in Break Out Box is standard portable 19” rack mountable with 128 Input and 128 Outputs.
-
Product
160-Pin DIN41612 Shielded Connector Block, Male
B1604MR-4F-0A
Connector Block
This connector block provides a simple method of connecting to high density DIN41612 connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage. The metal shell includes an internal insulation barrier under the carrier board.
-
Product
SHC68-68-EPM, 68-Pin Male VHDCI to 68-Pin Female D-SUB, Twisted Pair, Shielded Multifunction Cable, 0.5m
192061-0R5
Multifunction Cable
Connects to DAQ devices and modules, terminal blocks, bare wires, or other accessories. The multifunction cable models include a variety of industry-standard front- and back-end connectors, such as 68-pin VHDCI, 96-pin SCSI, and 68-pin SCSI. Cable selection depends on the connector types and requirements of the hardware you’re connecting to and the environment in which you’re using the cable. Some cables are internally twisted and shielded to more effectively reject ambient noise than an ordinary shielded cable. These cables are designed to work with high-performance NI devices.
-
Product
X13 GPIB Cable, MicroD25 to Shielded cable/Standard connector, 1M
183285-01
GPIB Cable
24-Pin Male/Female GPIB to 25-Pin Male Micro D-SUB GPIB Cable - The 24M-24F-MicroDB25M X13 GPIB Cable, sometimes referred to as the X13 cable, connects your system to GPIB devices or interfaces for instrument control. This standard shielded cable can connect PXI Controllers to instrument control devices and is offered in different lengths.
-
Product
X2 GPIB Cable,Double-Shielded,Shielded Plug/Receptacles,4 m
763061-03
GPIB Cable
24-Pin Male/Female GPIB to 24-Pin Male/Female GPIB, Stackable, Double-Shielded GPIB Cable - The 24M/F-24M/F X2 Cable, sometimes referred to as an X2 cable, connects your system to GPIB devices or interfaces for instrument control. The 24M/F-24M/F X2 Cable has 24-pin IEEE 488 male and female connectors, and the cable is double shielded with shielded plug/receptacles. The 24M/F-24M/F X2 Cable is also offered in different lengths.
-
Product
Shield Room
-
Our world depends on digital information & operation. An increasingly electromagnetically polluted environment, solar storms or weaponizing (H)EMP may put your operation at risk, leading to destroyed electronics, data breaches or even espionage. Owning an in-house high-performance RF-shielded enclosure is the best way to secure your critical operation and information. We understand your safety concerns. That’s why we strive for worry-free solutions with the highest level of security, precisely tailored to your needs.
-
Product
SH68-68R1-EP, Shielded Cable, Right Angle Connector, 1 m
187051-01
Multifunction Cable
68-Pin Female SCSI to 68-Pin Right-Angle Female SCSI, Twisted Pair, Shielded, 1 m Multifunction Cable - The SH68F-68R1F-EP Cable, sometimes referred to as SH68-68R1-EP, connects NI DAQ 68-pin devices to 68-pin accessories. The right-angle connector is useful for small spaces where clearance is limited.
-
Product
High Performance Embedded Box IPC
MIC-7000
-
The compact modular PC support i-module expansion to satisfy diverse application requirements. Modular computer reduces lead time for CTOS due to easy configuration and can be widely deployed for factory and machine automation.
-
Product
802.11a,b,g Dual RF Shielded Test Enclosure
JRE 0814-2R-A
-
Containing all the capability of the larger JRE enclosures, the rack mounted 0814-2R-A is ideal for testing IEEE 802.11 a,b,g devices such as; WLAN, VoIP, access points and other RF devices. Two independent 0814 series enclosures are mounted in one 19 inch rack. Two shielded vents provide excellent cooling and optional fan(s) are available for those hot products. Tough 'honeycomb' vents maintain shielding effectiveness throughout the frequency range. Featuring rugged welded aluminum construction, you can be assured of its tight RF shielding effectiveness.
-
Product
Decade Box, Calibrated W/D & U, Resistance, 7, 1ohm to 11.11111Mohm, 1 %
72-7270 CAL DU
-
The 72-7270 CAL DU from Tenma is a resistance decade box. It is ideal for service, prototype and experimental use. This useful tool may be set resistance value from 1 to 11,111,110 ohm in one ohm increments. The decade accuracy is ±1% resistors used throughout. It has weight of 320g/0.70lb and dimension 14.7cm × 11.7cm × 5.5cm (5.79" × 4.61" × 2.16"). It is typically used in general applications, troubleshooting, maintenance, education and vocational training, production line testing, radio and TV services, working standards, research design & develop, physics laboratory work.
-
Product
10 Ft Shielded Cable For 5xxx/35xx Products (68 Pin)
GT95028
-
10 ft shielded cable for 5xxx/35xx products (68 Pin)
-
Product
Breakout Box
T1000-15
-
T1000-15 breakout box with dual 15 pin D-Sub connectors for signal capture or monitoring. Dual connectors provide a total of 30 test points plus a ground jack. All test points use standard size 4mm banana jacks. Test points may be connected using shorting banana cable to allow signal continuity. Ideal for continuity measurements, isolation testing, and signal capture.
-
Product
SHC68M-68F-RMIO, 68-Pin Male VHDCI to 68-Pin Female D-SUB, Shielded Multifunction Cable, 2m
189588-02
Multifunction Cable
68-Pin Male VHDCI to 68-Pin Female D-SUB, Shielded Multifunction Cable - The SHC68M-68F-RMIO Cable, sometimes referred to as SHC68-68-RMIO, connects to the terminal block of a multifunction reconfigurable I/O (RIO) device. The SHC68M-68F-RMIO Cable is offered in different lengths.
-
Product
BNC-2121, 68-Pin Female SCSI to Female BNC and Screw Terminals, Function Generator and Encoder, Desktop Mount, Shielded Terminal Block
778289-01
Terminal Block
68-Pin Female SCSI to Female BNC and Screw Terminals, Function Generator and Encoder, Desktop Mount, Shielded Terminal Block - The BNC-2121 features eight dedicated and six user-defined BNC connectors and spring terminals, which allow access to all I/O signals. You can also use this terminal block to provide pulse-train, trigger, and quadrature encoder signals. The BNC-2121 includes a desktop mount.
-
Product
PXI 50 Shielded SPST Reed Relays
40-142-021
Reed Relay
The 40-140A/141/142/143 range of high density switching modules are available in Normally Open (SPST & DPST) and changeover (SPDT) configurations. Connections are made via a front panel 200 pin female connector.
-
Product
Signal, Patchcord, ITA, 36", QuadraPaddle, 24AWG Single Conductor Shielded, Single Ended
7-121974000-036
Signal Patchcord
Signal, Patchcord, ITA, 36", QuadraPaddle, 24AWG Single Conductor Shielded, Single Ended.
-
Product
Stainless Steel Junction Box
JB104SS
-
The JB104SS junction box model is designed to connect and trim up to four load cells per board. It may also be used in combination with additional juction boxes through the use dof an expansion port on the main board to connect multiple junction boxes thus allowing the summing of more than four load cells.
-
Product
SH25M-10F Cable, 25-Pin Male D-SUB to 10-Pin Female COMBICON, Shielded Multifunction Cable
190654-02
Multifunction Cable
25-Pin Male D-SUB to 10-Pin Female COMBICON, Shielded Multifunction Cable - The SH25M-10F Cable, sometimes referred to as SH10F-25M, connects C Series DAQ devices with a 10-pin screw terminal to a 25-pin D-SUB. The SH25M-10F Cable is offered in different lengths.
-
Product
Aspirated Radiation Shield
-
The fan has an ingress protection (IP) rating of 55, virtually eliminating moisture and dust ingress. At full speed the power requirement is 1 W (80 mA at 12 V DC). To conserve power fan speed can be reduced, via pulse width modulation (PWM), to 0.3 W at night or when wind speed is greater than 3 m s-1 without loss of accuracy. If the fan is continuously operated at full speed lifetime is rated at 50,000 hours (5.7 years). The fan includes a tachometer, allowing RPM to be mounted to detect obstruction of the fan.
-
Product
Mini Coax, Contact, ITA, RG316 Double Shield
610103152
Coax Contact (ITA)
Mini Coax, Contact, ITA, RG316 Double Shield.Mechanical SpecificationsDurability 20,000 cyclesContact Material Shield – BrassCenter Conductor – BeCuContact Plating Shield – 50µ" Au over 100µ" NiCenter Conductor – 60µ" Au over 100µ" NiContact Termination Center Conductor - SolderShield - CrimpInsulator PTFEMating Force 1.5 lbs max [0.68 kg]Electrical SpecificationsCharacteristic Impedance 50 ΩFrequency Range DC to 1 GHzVSWR ≤ 1.06 @ 1 GhzInsertion Loss 1.2 dB @ 1 Ghz1.02 dB @ 500 MhzDWV 1500 VDC Min.Contact Resistance 5 mOhms center/ 3 mOhms outer Cable Specifications RG316 Double ShieldEnvironmental SpecificationsOperating Temperature -50°C to +105°CInsulation Resistance 1000 MΩ min.
-
Product
MAX31855 K-Type Thermocouple Arduino Shield
SEN-30004-K03
-
Four channel MAX31855 digital thermocouple Arduino Shield. Two versions of this shield are avaliable for each thermocouple type: either 'Ch 0-3' (CS pins use Uno/Mega IO pins 7-10) or 'Ch 4-7' (CS pins use Uno/Mega IO pins 3-6), with the only difference being which set of zero-ohm resistors are populated on the board. This allows use of other SPI devices that may be 'hard coded' to specific digital pins on the Arduino, or simply stacking one of each type together to get a total of eight thermocouple channels on one Arduino. The MAX31855K supports a measured temperature range of -270C-1372C with known thermal characteristics and output resolution of 0.25C. Included thermocouple connectors are type-specific to provide proper material continuity as close to the IC as possible. The SEN-30004 is interfaced via 3 or 4-wire SPI and a high-speed level shifter is included to allow the board to plug directly into an Arduino Uno or Mega
-
Product
SHC68-C68-RDIO2, 68-Pin VHDCI Male to 68-Pin VHDCI Male, 80 MHz, Shielded Digital Cable, 2m
156166-02
High Speed Digital Cable
SHC68-C68-RDIO2 Shielded R Series High Speed Digital Male VHDCI Cable, 2m
-
-
Product
Battery Boxes Testing Equipment
-
Battery boxes can be tested for faults by placing the box on a metal plate. By applying a test voltage to an electrode inside the box, the moulding can be checked thoroughly - particularly at the injection points - and any faults found. Defects will be identified by a spark passing from the electrode, through the defect itself, to earth (the conductive material placed outside the battery box.
-
Product
Meter Box Series
-
Shenzhen Star Instrument Co., Ltd.
The single-slot meter box for single-phase DIN rail energy meters has a window for load switch control if a load switch is installed.
-
Product
Arduino CAN Shield
IFB-10003-INP
-
CAN (Controller Area Network) communication has become ubiquitous in industry. It is used in automotive applications (part of OBD and many other datalinks), on-highway trucks (J1939), industrial machinery and instrumentation, and equipment applications (factory automation). This shield is designed to provide a CAN 2.0 front-end interface for 5V Arduino modules (Uno, Mega, etc). The module uses SPI to communicate to the Arduino, and requires an aditional chip select pin. An optional interrupt line to the MCP2515 and two LEDS are also provided. The chip select and interupt lines are selected via zero ohm resistors and have several configuration options for flexibility stacking additional shields. A set of stackable headers is included with this board, not installed. An optional on-board voltage regulator may be used to supply 7.5V to the Arduino's 'Vin' pin (which is regulated to 5V by the Arduino's on-board LDO). The CAN shield regulator supports a wide input range of 9V to 32V. This makes it possible to cleanly build a stand-alone CAN node (remote sensor) without the need for a separate Arduino power supply!
-
Product
MAX31856 Thermocouple Sensor Arduino Shield
SEN-30007-K
-
Quad channel thermocouple Arduino shield based on the MAX31856 universal digital thermocouple interface IC. This is an exciting update of the MAX31855, with improvements in resolution (19 vs 14 bits), on-board temperature reference (6 vs 4 bits), and compensation (fully compensated vs nonlinear correction required). The MAX31856 is interfaced via 4-wire SPI with options for interrupt triggering. An LDO and a high-speed level shifter are included on ALL device pins to allow interfacing with to any Arduino - both 3.3V and 5.0V variants - without sacrificing device performance in any operating condition.
-
Product
Shielding Cube
CMQ200
-
The R&S®CMQ200 is a compact and fully integrated solution to cover most 5G devices in various applications. The drawer concept enables fully automated handling in manufacturing environments. The robust mechanical design ensures millions of test cycles for reliable mass production environments. The flexible cube design covers applications for smart devices, CPEs, RFIC and prototypes. R&S®CMQ200 is ready for 5G and other technologies in the frequency range from 20 GHz to 77 GHz.
-
Product
RF Shielded Enclosure for Pre-Compliance EMC and CTIA Testing
QuietBox-AR "Mini-Range"
-
The Raymond RF QuietBox-AR is a mobile solution for pre-compliance EMC and CTIA testing, 3D antenna pattern measurement, and total radiated power & total isotropic sensitivity testing. Fully equipped with client-specified broadband absorber, integrated antenna and rolling cart, the QuietBox-AR is a cost effective option for product verification prior to fully compliant testing.
