Wire Locators
detect an induced or directly transmitted signal through a cable to trace its location.
-
Product
Receiver, 9050, 50 Module, Dual Discrete Wiring Tiers, EMI Gasket
310104429
Receiver
The 9050, 50-module receiver is rugged and designed to accommodate high I/O and suited for larger test and measurement systems. Both tiers are designed for discrete wiring and can accommodate individual 9025 ITAs. This 9050 also offers a gasket for EMI applications.
-
Product
10 Micron Wire Grid Polarizer
-
Fabricated from 10 micron diameter tungsten wire, and with a choice of wire spacing starting from 25 microns, these wire grid polarizers are suitable for use from approximately 100 microns (or 3 THz) to longer wavelengths. Please refer to the table below for the standard availability of wire spacing and frame clear aperture / outer diameter.
-
Product
Coax, Module, Receiver, CASS, 64 Position, Discrete Wiring or Side PCB
510113121
Receiver Module
Coax, Module, Receiver, CASS, 64 Position, Discrete Wiring or Side PCB.
-
Product
Wireless Wire Break Detection System
A909
-
The A909 is a wireless system that allows to detect wire breaks for cabling machines having no sliding contacts brushes.
-
Product
Gauge Type T Thermocouple Wire
W-TW-44P
-
Most thermocouple wire used in the manufacture of sensors is "Special Limits" wire which, to meet NIST standards, must be accurate to 0.5°C in the range 0-50°C. This means that even with most sophisticated electronics, the best possible accuracy for the system is 0.5°C.
-
Product
LXI Wired Trigger Bus Adaptors and Accessories
Chassis
All of our wired trigger bus products have been discontinued because of obsolescence issues. The products shown below are only to support our existing users. Manuals and data sheets are provided for information only.
-
Product
Lamp & Fixture Wiring Tester
GT3110GAM LAMPCHEK
-
LampChek indicates the lamp and fixture continuity.
-
Product
Glow Wire Test Apparatus
GWT A2
-
GLOW WIRE TESTER (also known as Glow Wire Test Apparatus) is designed to carry out fire hazard testing as specified in IEC 60695-2-10 2000-10. Flammability test is to check the ‘Resistance to Fire’ of electrical insulators that touch directly conducting parts & also parts of insulators. This test is also referred in many other standards such as IS 11000, IS 3854 : 1997 / IS 1293 :1988 / IS 371 :1999 & IS 11000 Pt 2 Sec 1, IEC 60335, IEC 884/94, IEC 60598, IEC 61058, BS 6458, BS EN 60695–2-10,11,12, etc.
-
Product
Test Lead Holder For Wires Up To 0.450In (11.43mm) Dia.
2708
-
Test Lead Holder for Wires Up to 0.450in (11.43mm) Dia.
-
Product
Pull-Thru Adapter, Wired, QuadraPaddle, VHDCI ML, f/ NI PXIe-6386
510140339
Pull-Thru Adapter
Pull-Thru Adapter, Wired, QuadraPaddle, VHDCI ML, f/ NI PXIe-6386.
-
Product
Signal, Module, ITA, QuadraPaddle, 90 Series, 192 Position, Fully Loaded w/ Square Posts for Wire Wrap with Anti-Rotation (610 138 122)
510151124
ITA Module
NOTE: Part # 510151124 Rev D and higher utilize captive screws that cannot be replaced with screws from currently VPC- offered screw kits.Primary mating module 510150115. (May mate with other Receiver modules, as well.)
-
Product
Temperature Wire And Cable Tools
-
Omega's specialized tools for stripping, welding and crimping wire and cables help you complete your project safely and on time.
-
-
Product
High Altitude Wiring Clamp
-
Weshine Electric Manufacturing Co., Ltd
1. The operation is simple, through pushing and pulling the special operation lever can realize the clamp mouth free opening and closing, complete the wiring work.2. Connection clamp between the upper and lower jaws of the use of the principle of moving pulley to save the effort, the use of smaller tension can be obtained larger clamping force.3. There is a steel needle inside the clamp mouth to ensure good contact between the clamp mouth and wiring position
-
Product
Non-destructive Eddy Current Testing of Long Products such as Tubes, Rods, Wire, and Profiles
DEFECTOMAT® Product Familiy
-
Foerster Instruments, Incorporated
The DEFECTOMAT systems by FOERSTER were specially developed for quality testing and process monitoring of long products. From hot testing to all bright steel processing steps, the surfaces of semi-finished products made from austenitic, (non) ferromagnetic metals can be tested for defects. The DEFECTOMAT systems operate in a contactless and non-destructive manner in accordance with the eddy current method and are used for detecting short defects, such as holes or localized defects and transverse defects. The systems detect defective materials fully automatically and reliably. Defects can be marked, classified, and automatically discarded. the test speed of up to 150 m/s facilitates 100% testing, even at high production speeds. The systems benefit from low operating costs and frugal energy consumption as well as low maintenance costs, few wear parts, and low use of materials.
-
Product
Wired Adapter for PXI, for National Instruments PXI-4110
510109469
Pull-Thru Adapter
Wired adapter or pull-thru from a 64 position TriPaddle receiver module to one 6 position Mini-Combicon plug and one 2 position Mini-Combicon plug.
-
Product
Fiber Visual Fault Locator
-
Fiber visual fault locator is a pen type device which is able to locate the breakpoint, bending or cracking of the fiber glass,this small fiber optic equipment can locate the fault of OTDR dead zone and make fiber iIdentification from one end to the other end .
-
Product
MTA Wiring Analyzer
2650
-
DIT-MCO's newest test solution, the Model 2650, incorporates modularity so that the system conforms to your testing needs. The modular switching units can rack-and-stack in a cabinet providing concentrated test points or can be distributed around the Unit Under Test (UUT) eliminating long, cumbersome adapter cables. Or you may reconfigure the system at any time when your needs or the UUT changes.
-
Product
Strain Relief Plate, Receiver/ITA, SIM Module, For Wired Solutions
510109568
Strain Relief
Strain Relief Plate, Receiver/ITA, SIM, for wired solutions.
-
Product
Utility Locator
VM-810
-
Using the correct frequency makes a world of difference when locating buried utilities. The depth of the utility, size, material, and amount of congestion (proximity of other utilities) all need to be taken into consideration for the correct frequency selection. Large diameter, direct buried pipes with bell housing ends that use insulators and rubber gaskets, such as water or gas require a higher frequency while smaller diameter, well-grounded direct buried or long distance in conduits work, better with a lower frequency. The VM-810 operates at 83.1kHz which is ideal for water and gas utilities which generally are larger pipes with bell housings and gaskets. The VM-810’s higher frequency is also good for locating ungrounded small diameter drop wires and inducing signals through the soil, onto services when direct connecting is not an option.
-
Product
Wire Sorter
-
Shanghai Beha Electronics Co., Ltd.
*Standard signal transmitter identifies up to 12 lines*Clear indication of short circuits, open circuits, or interruptions*Integrated continuity tester
-
Product
High Force Type Prbobe For PCB, K100 Series 100 Mil Pitch, Receptacle With Wire Wrap Pin
KR100-WP
Spring Probe
K100 Series, Pitch 100mil, Receptacle, with wire wrap pin. Brass with gold finish.
-
Product
Probes With Lead Wires
-
Used when the probe is installed some distance from the logger, controller, or other data acquisition device. Available in a variety of lead wire types with stripped leads or connectors attached.
-
Product
Multi-Channel PD System Locator
PDiagnostic Series
-
Power Monitoring and Diagnostic Technology Ltd.
The PDiagnostic is a portable system that utilizes Ultra-High Frequency (UHF), Acoustic Emissions (AE), High-Frequency Current Transformer (HFCT), and Transient Earth Voltage (TEV) sensors to detect, analyze, and locate the PD signals in real time for a multitude of medium and high voltage electric power equipment.The multi-channel PDiagnostic system locates PD on power equipment down to a meter by utilizing Acoustic-Electromagnetic Combination Location Technique, Time Difference of Signals’ Arrival (TDOA), Partial Discharge Signals Separation (PDSS), and 3D Positioning Technology with PC software included.The system features advanced PD diagnostic capabilities, automatic PD type pattern recognition, and accurate PD location capabilities. The PDiagnostic is an ideal trouble-shooting tool for your PD programs. Severity is determined and maintenance suggestions are provided accordingly.
-
Product
LAN and telephone wiring testers
-
Measurement and analysis instruments for the deployment of telephony networks, Ethernet, and generally telecommunications networks via copper cable.
-
Product
VTAC Patchcord, Receiver, 36", VTAC, 2x 1000Base-T1 UTP Wire H-MTD Cable Jack, 1 Position
7-142716765-036
VTAC Patchcord
VTAC Patchcord, Receiver, 36", VTAC, 2x 1000Base-T1 UTP wire H-MTD Cable Jack, 1 Position.
-
Product
AUDIO LOCATOR PROBE
45/90
-
Easy to operateUnaffected by surface coverLight weight and strongWater resistant, build for rugged field useTelescoping handleDepth locator "bubble"
-
Product
Underground Cable Fault Locator
KM-CFPL-620 /620B
-
Kusam Electrical Industries Limited
“KUSAM-MECO” underground Cable Fault Pre-locator is an automatic Cable Fault Locator which adopts ARM, FPGA & Dot Matrix Color LCD display Technology. This tester combines both pulse reflecting technology (TDR) & (intelligent Bridge testing (Bridge) (Model-KM-CFPL-620B) for measuring the exact fault location such as broken line, cross faults, earthing, (poor insulation & poor contact of the lead covered cables as well as plastic cables. (Model-KM-CFPL-620B)).It is a microprocessor based fault locator with a user friendly menu. It is easy to operate. It tests almost all telecom & signal cables. It has an English menu which is easy to understand & use. With Megameter & Ohmmeter it enables to test insulation resistance & loop resistance. It has USB Port for uploading test data to computer
-
Product
Pull-Thru Adapter, Wired, QuadraPaddle, to 100 Pin ML SCSI, f/ NI PXI-6514/15, 6509
510140113
Pull-Thru Adapter
Pull-Thru Adapter, Wired, QuadraPaddle, to 100 Pin ML SCSI, f/ NI PXI-6514/15, 6509.
-
Product
15' Cable, 78-Pin Male Connector On One End, Loose Wired (Numbered) Other End
GT97112
-
15' harness, 78-pin male D-sub connector on one end, loose wired (numbered) other end.
