Wire Locators
detect an induced or directly transmitted signal through a cable to trace its location.
-
Product
3 Wire (Analogue) Earth Resistance Tester
1105 ER
-
Standard Electric Works Co., Ltd
● Capable of measuring earth resistance and earth voltage.● 2mA measuring current permits the testing of earth resistance without tripping earth leakage current breakers in the circuit under test.● In addition to facilitating for precision measurement, test leads for simplified two-wire measuring system also are supplied as standard accessories.● Battery operated.● Battery life indicator. ● Calibration performed with supplied test leads.
-
Product
Wiring Analyzers for Cables, Wire Harnesses, Backplanes
CableEye M2Z, M3Z, M4
-
With our cable testers and harness testers, find defective or miswired cables instantly before they damage equipment or waste valuable technician time. CableEye® all-in-one test and cable management systems have a unique, patented graphic wiring display to visually pinpoint problems when wiring errors are detected, and offer under a second pass/fail testing for production environments. Quickly locate intermittent connections and identify their position in the cable.
-
Product
Precision Cable Locator Range
-
Radiodetection’s precision locators are designed for optimal locate performance for damage prevention professionals working in all industries and utilities.
-
Product
Ground Fault Locator
K-800
-
Kongter Test & Measurement Co., Limited
Kongter’s K-800 Ground Fault Locator is the new model which is developed to fast detect, trace and pinpoint virtual ground faults in LIVE DC systems where electrical cables have breakage with current lost to ground.
-
Product
2.5mm Visual Fault Locator
3105
-
Anfkom International Co.,Limited
The 3105 Pen type VFL is specially designed for field personnel who need an efficient and economical tool for fiber tracing, fiber routing and continuity checking in optical network. It includes:Finding the breakpoint, poor connections, bending or cracking in fiber optic cables.Finding the faults of OTDR dead zoneEnd-to-end visual fiber identification
-
Product
Advanced Wire Tracers
-
Amprobe’s Advanced Wire Tracers provide accurate results in minutes with new features and technologies that simplify wire tracing and breaker identification, including two optimal frequencies for both energized and de-energized wire and breaker tracing in walls, ceilings, and floors.
-
Product
Non-destructive Eddy Current Testing of Long Products such as Tubes, Rods, Wire, and Profiles
DEFECTOMAT® Product Familiy
-
Foerster Instruments, Incorporated
The DEFECTOMAT systems by FOERSTER were specially developed for quality testing and process monitoring of long products. From hot testing to all bright steel processing steps, the surfaces of semi-finished products made from austenitic, (non) ferromagnetic metals can be tested for defects. The DEFECTOMAT systems operate in a contactless and non-destructive manner in accordance with the eddy current method and are used for detecting short defects, such as holes or localized defects and transverse defects. The systems detect defective materials fully automatically and reliably. Defects can be marked, classified, and automatically discarded. the test speed of up to 150 m/s facilitates 100% testing, even at high production speeds. The systems benefit from low operating costs and frugal energy consumption as well as low maintenance costs, few wear parts, and low use of materials.
-
Product
Wire Bend Tester
-
CSZ chamber is designed for this type of cold bend test. Each chamber is designed to meet the customer's size and temperature requirements. Chambers feature power-driven mandrels that are typically mounted at the top and bottom of the chamber for the wire to wrap and bend around. Mandrel diameters are selected by the customer and supplied in a variety of sizes.
-
Product
Super-Safeway Three Wire & GFCI Circuit Tester
1301270003
-
Super-Safeway Three Wire & GFCI Circuit Tester, 3 Indicating Lights, Push to Test Button
-
Product
Hipot Wire Harness Testers
NX Hipot
-
* 50 to 1500VDC Hipot Testing* 50 to 1000VAC (optional) * 5Mohm to 1Gohm Insulation Resistance * Simple 4-button user interface * Tests for continuity and shorts * Tests a variety of components * Precision resistance measurements * Continuous high speed scanning for real time complete status information of harness assembly progress * Keyed security access and control * Built for rough industrial environments * 2 serial ports for connection to printers and scanners * Standalone operation * Uses a high capacity memory card * Available from 64 to 1024 test points * Networkable
-
Product
Strain Relief Plate, Receiver/ITA, SIM, PCB or wired solutions
510109598
Strain Relief
Strain Relief Plate, Receiver/ITA, SIM, PCB or wired solutions.
-
Product
Wire Crimp Testers
-
Imada offers manual and motorized wire crimp test systems in either vertical or horizontal configurations.Lever-operated systems offer basic functionality and rapid destructive testing up to 220 lbf.Motorized systems have speed control and are capable of destructive or force-controlled non-destructive testing up to 1100 lbf.Choose from manual or automatic wire-gripping fixtures.Digital gauges offer data output for analysis with data acquisition software.Create your own custom configuration or consult our application specialists.
-
Product
Telephone Line, PCM and Other Copper Wire Tester
-
Wuhan Sunma Technology Co., Ltd.
SunmaFiber Tel Line, PCM and Other Copper Wire Tester is developed for the fault testing of local telephone circuit using internationally advanced measuring technique in connection with the current situation of domestic telephone network. The instrument is of portable structure, and specially designed for the use of telecom and exchanger room operating staffs, line attendants, mobile phone servicing staffs and etc.
-
Product
Ground-Fault Location Products for Ungrounded Systems
-
When combined with Bender's ground-fault detectors and current transformers, EDS series modules provide fast, automatic ground-fault location in ungrounded systems. Fault location takes place while the system remains online without the need to open branch circuit breakers or disconnect equipment. Bender's fault location system works on both AC and DC systems, as well as systems with variable frequency drives. A standalone, portable fault location system is also available.
-
Product
One Wire Communication Board
MS 1727
-
- Digital serial bus communication with low speed data over a single line, Both signaling and driving power over a same single signal.- Protocol used in small inexpensive devices. Such as digital thermometer, weather instruments, laptop sub module, authenticate system and some cell phone battery packs.- Always master only initiates the communication and in overall in charge of the network.- Bus communicates with master and slave at a low data rate of 12kbps.- All terminals in the network are communicating by half-duplex mode.- Maximum of 255 nodes in each 1-wire network- Each data transaction will start with 480micro second low RESET pulse.
-
Product
PXI Pull-Thru Adapter, Wired, QuadraPaddle, to Two 68 Pin Male VHDCI
510140114
Pull-Thru Adapter
PXI Pull-Thru Adapter, Wired, QuadraPaddle, to Two 68 Pin Male VHDCI
-
Product
3 Wire (Digital) Earth Resistance Tester
2120 ER
-
Standard Electric Works Co., Ltd
● Capable of measuring earth resistance and earth voltage.● 2mA measuring current permits the testing of earth resistance without tripping earth leakage current breakers in the circuit under test.● The test leads are supplied as standard accessories for simplified two-wire measuring system.● 0Ω adjustment.● Battery operated.● Data hold function.● Low battery indication.● Calibration performed with supplied test leads.
-
Product
Protective Cover, 9050, VXI and Discrete Wiring, ITA
410112582
Protective Cover
When storing the ITA, the cover snaps on to protect the modules and contacts. The body of the cover is clear chromated aluminum and the mounting blocks are made of Delrin.
-
Product
Visual Fault Locator
VFL X5003
-
Constant & stable output powerLow battery warning, reminds users to change the battery timely.Long battery life (up to 40 hours with AAA batteries)Pocket size and light weight, easy to use.Re-changeable ceramic tube, to avoid returning to manufacturer for this small fault.
-
Product
Receiver, 9050, 50 Module, Dual Discrete Wiring Tiers
310104368
Receiver
The 50 Module Receiver is a rugged system devised to accommodate high I/O. With high contact point availability, the 50 Module Receiver is suited for larger test and measurement systems. Both tiers are designed for discrete wiring, and can accommodate individual 9025 ITAs.
-
Product
Drawing Die And Wire Measurement
Wire Diameter And Roundness Measurement
-
Optik Elektronik Gerätetechnik GmbH
The DGMS is a measuring system for diameter and roundness of wires, drawing dies and enameling dies. The wire diameter is measured highly accurate by an image processing system. To measure the roundness, an additional special holder is necessary to rotate the wire for the diameter measurement in several azimuths. The accuracy of the measurement is ‹1micron.
-
Product
Signal, Module, Receiver, CASS, 210 Position, Discrete Wiring
510113125
Receiver Module
Module, Receiver, Cass, Signal, 210 Position, Discrete Wiring
-
Product
PDS Wire Crane Monitoring System
-
It shows a real time overview of the wire crane in navigation, profile, and 3D views; displaying the clamshell, pontoon/vessel, design depths and color-coded digital terrain model (DTM). The navigation view highlights the high and low spots and is updated in real time, registering the progress of the dredging work. The registration follows the shape of the clamshell, bucket or orange peel bucket and is visible immediately in all views. The system also shows the open/close status of the dredge tool. Up/down indicators show the operator the exact distance to the seafloor and design depth continuously. 3D design models allow the use of complex designs.
-
Product
Structured Wiring
-
Structured wiring refers to a whole-house network of audio, video, data, telephone, television, home automation or security signals. This wiring can be installed when a home is being built. It may be put in during a remodel. Structured wiring can also be added on its own.
-
Product
K-Type Thermocouples Wire, Fiberglass (32deg F to 900deg F) 2 m
745690-K002
Thermocouple Contact (ITA)
K-Type Thermocouple, 32°F to 900°F Temperature Sensor - The K-Type Thermocouple works with NI measurement devices and software to help you acquire temperature data within a measurement system. You can use LabVIEW or FlexLogger software and NI-DAQmx driver software to configure measurements and predefined scaling coefficients for the K-Type Thermocouple and acquire synchronized temperature data in units of degrees. The K-Type Thermocouple is available in various lengths and configurations including field-cuttable, ready-made sensors, and thermocouple wire extensions with a -20°F to 221°F temperature range.
-
Product
Pipeline & Cable Fault Locator
TM2000
-
TM2000 Pipeline & Cable Fault Locator is designed for the Underground utilities route locating, the depth measuring and disatance tracing.
-
Product
Fault Finder for Electrical Wiring Open / Short Circuit
FF310
-
42 V Ready: for use in the new generation of vehicles with mixed or single 42 Volt systems. Operates on DC voltages from 6 to 42 volts. Internally protected against power surges and overloads. 8" flexible probe allows reaching wires in congested places. Transmitter and Receiver LEDs show open or short circuit conditions.
-
Product
Handheld Cable Fault Locator
TM800H
-
TM800H Handheld Cable Fault Locator adopts TDR (Time Domain Reflection), new signal process and data collection technology. It can locate the distance of cable break and mix faults accurately. TM800H can be widely used in the communication installation, maintenance and general wiring. It can troubleshoot not only the local Telco-cable, but also Network cable. Its high sampling rate makes the measurement dead zone as narrow as 1 meter. This makes it a straightforward, user-friendly test solution.
-
Product
Visual Fault Locator
TM191
-
TM191 series visual fault locator is used for the measurement in single mode or multi-mode fibers. It features a rugged design, a universal connectorand an accurate measurement
-
Product
Cable Sheath Fault Location
-
Locating cable sheath faults is one of the last steps in cable testing, occurring after you have identified the existence of a cable fault via the identification procedure based on your specific site variables and the type of system you are working on
