Extender Boards
move out from slot circuit card giving access thereof.
See Also: Extenders, Extender Cards, Test Boards, Bus
-
-
product
Adaptive Relay Board, Virtex-6 FPGA - PCIe
Model 78624
Model 78624 is a member of the Cobalt® family of high-performance PCI Express boards based on the Xilinx Virtex-6 FPGA. As an IF relay, it accepts two IF analog input channels, modifies up to 34 signals, and thendelivers them to two analog IF outputs. Any signal within each IF band can be independently enabled or disabled, and changed in both frequency and amplitude as it passes through the module. The 78624 supports many useful functions for both commercial and military communications systems including signal drop/add/replace, frequency shifting and hopping, amplitude equalization, and bandwidth consolidation. Applications include countermeasures, active tracking and monitoring, channel security, interception, adaptive spectral management, jamming, and encryption.
-
product
Accelerometor, Gyro, Magnetometer Breakout Board
SEN-38001
The LSM9DS1 is a highly configurable, flexible and precise motion sensing solution from ST Microelectronics - the latest in a wide-ranging inertial product line. It integrates a 3-axis accelerometer, 3-axis gyroscope and 3-axis magnetometer into a single IC , giving you a full nine degrees of freedom (9-DOF) in a tiny 3mm x 3.5mm package. Even with support components, square mounting pattern and connection breakouts for both SPI and I2C, this board is barely the size of a quarter.
-
product
Multiprotocol P104Plus Interface Board for Embedded Applications or Avionics Test & Simulation Applications
EXC-4000P104plus
The EXC-4000P104plus is a multiprotocol P104plus interface board for embedded applications or avionics test and simulation applications. Each board holds up to five independent modules. Two on-board modules use the MIL-STD-1553 communications protocol (M4K1553Px); another on-board module uses the ARINC-429 communications protocol; two additional detachable modules can be any one of the following types:M4K1553PxS (Single Function - RT validated) This module operates as a Bus Controller, Remote Terminal or a Bus Monitor. This module qualifies for airborne applications.M4K1553Px (Multi Function) This module operates as a Bus Controller, up to 32 Remote Terminals and as a Bus Monitor. Supports an Internal Concurrent Monitor in RT and BC/RT modes.M4K1553Px(S)-1760 Same as M4K1553Px(S) plus MIL-STD-1760 options.M4KMMSI Mini Munitions Store Interface module. Supports RT, BC/Concurrent-RT/Concurrent Monitor and Bus Monitor modes. Up to 8 hub ports EBR-1553 [10 Mbps 1553 protocol using RS-485 transceivers] and 1 monitor output.M4KH009 Based on our H009 family. This module operates as a Central Computer Complex (CCC) and/or up to 16 Peripheral Units (PUs) simultaneously, or as a Bus Monitor. In addition, a Concurrent Bus Monitor enables concurrent monitoring of the bus during CCC and PU simulation.M4K429RTx Based on our ARINC 429RxTx board. This module supports either five or ten ARINC 429 channels each of which can be configured in real time as a receive or transmit channel.M4K708 This module supports two channels of ARINC 708/453, each one selectable as either transmit or receive.M4KSerial This module supports up to 4 independent channels of serial communications, each of which can be selected as RS485, RS422 or RS232.M4KDiscrete This module supports 20 selectable input/open collector output discretes. The module supports TTL (0 to 5 volts) or avionics (0 to 32 volts) voltage levels.M4KCAN This module supports up to 6 independent channels of CAN 2.0B protocol with standard and extended message frames and message identifiers.
-
product
Digital I/O Board, 16 Optically Isolated I/O Channels, 24V
APCI-1516
PCI interface to the 32-bit data bus? 8 isolated input channels, 24 V? 8 isolated output channels, 10 to 36 V,output current 500 mA? Timer-programmable watchdog for the reset of the outputs to ??? One ground line for all inputs and one ground line for all outputs? Outputs set to "0" at PowerOn/Reset
-
product
Intel x51 Based Boards
MS 1507
- General Purpose I/O Signals- RS232/422 Interface- External Bus, External Interrupts
-
product
VME Form Factor Extender, 3U, 60mm
111FFE3006-01XX
The VME form factor extender 3U 60 mm allows to adapt boards for use in the same VMEbus system. It maintain the correct depth dimensions and allow the front panel to be aligned.
-
product
High Frequency Clock Divider Board
Alliance Support Partners, Inc.
Clock Divider is designed to divide high frequency signals, up to 2.5GHz, from 4 to 256 times. It will accept single ended (Unbalanced) or differential (Balanced) signals with amplitudes as little as 100mV rms. The clock division is controlled by 4 shunt jumpers. The circuit can be disabled and the divide by counter reset with 2 control signals. The on board regulator will accept voltages from 4.85 to 15.0V. The output is capable of driving 700mV Peak to Peak into 50 Ohms.
-
product
Motion Control Board, PCI
APCI-8001-1
*Axis control for 1 servo or stepper motor*Onboard processor*Optical isolation*16-bit analog output channels*Direct connection of commercially available incremental encoders *or SSI absolute encoders
-
product
Low Voltage Boards
- 6 or 8 independently controllable full floating channelsup to 64 V- Up to 60 W Max channel output power- High resolution on voltage set- Programmable TRIP parameter- Programmable ramp up / down- Current generator operation in overcurrent condition- Overcurrent programmable protections- Individual remote sense lines- Up to 0,2 mV voltage monitor resolution- Up to 1 mA current monitor resolution- Voltage ripple smaller than 3 mVpp
-
product
Analog Multiplexer Board
104-AIM-32
The 104-AIM-32 is an analog signal multiplexer conforming to the PC/104 standard. The card will multiplex and condition 16 differential or 32 single-ended analog signals before passing them to an analog-to-digital converter card like the 104-AIO12-8. A system may comprise one to seven of these cards in tandem with one 104-AIO12-8 A/D converter board. The 104-AIM-32 card may be used as part of a large data acquisition system. The 104-AIM-32A Kit consists of one 104-AIM-32 and one 12-bit 8-input A/D board.
-
product
PMCspan PMC Expansion Board
PMCspan
SMART Embedded Computing’s PMCspan allows users to customize and expand I/O options when coupled with a Smart SBC.
-
product
OSFP-XD Thermal Load with a Controller Board
In an everchanging industry, new form factors are launched to support higher speeds like 800G and later, 1.6T. With the speed per lane increasing exponentially, the need for thermal and cooling tests also rises with new requirements and demands.MultiLane is offering a OSFP-XD thermal load with a controller board, with the goal of emulating transceiver thermal behavior, but also to test cooling systems.
-
-
product
Analog Input Expansion Termination Board
MSXB 024
Analog Input Expansion Termination Board expands 8 analog input lines to 32 analog input lines and provides connection points for each line. Each of the two models has an onboard temperature reference sensor for cold junction compensation.
-
product
One Wire Communication Board
MS 1727
- Digital serial bus communication with low speed data over a single line, Both signaling and driving power over a same single signal.- Protocol used in small inexpensive devices. Such as digital thermometer, weather instruments, laptop sub module, authenticate system and some cell phone battery packs.- Always master only initiates the communication and in overall in charge of the network.- Bus communicates with master and slave at a low data rate of 12kbps.- All terminals in the network are communicating by half-duplex mode.- Maximum of 255 nodes in each 1-wire network- Each data transaction will start with 480micro second low RESET pulse.
-
product
PCIe Digital I/O Board, 32 Optically Isolated I/O Channels, 24V
APCIE-1532
16 digital inputs, 24 V, isolated16 interruptible inputs16 digital outputs, 24 V, isolated, 10 to 36 V, 500 mA/channelOptical isolation 1000 VWatchdog for resetting the outputs to "0" (when Power-On)Protection against fast transients, overvoltage, electrostatic discharge and high-frequency EMIInputs: voltage reversal, input filtersOutputs protected against short circuitOvertemperature and overvoltage protectionDiagnostic report in case of short circuits, overtemperature, voltage drop ...24 V power outputs with protection diodesShutdown logic when the external supply voltage drops below 5 V
-
product
I/O Board With Two COM, Four USB 3.0, VGA And Audio For PICO880, PICO500, PICO300
AX93275
*Specifications: 1 x RS-232/422/485, 1 x RS-232, 4 x USB 3.0, 1 x VGA, 1 x Audio (MIC-in/Line-out), 1 x Power On, 1 x Reset, 2 x LED*Dimensions: 118 x 40 mm*Compliant products: PICO880, PICO500, PICO300
-
product
16 Bit PXI I/O Board With 32 Or 64 Analog Outputs
CP266
The CP266 is a single-width, 6U, CompactPCI module with 32 or 64, 16-bit analog output channels. These independent analog channels provide ±10 V full-scale outputs. The channel update rate is 2ms, and each output is accurate to ±1mV. The power-up state of the analog outputs can be set to independent user-defined values. Paired output signals are provided to eliminate ground offset effects. The analog outputs are available at a single 68-pin SCSI II shielded connector (32-channel option) or a pair of 68-pin SCSI II shielded connectors (64-channel option).
-
product
PC/104 OneBank Board
EMC2-ZU3EG
Sundance Multiprocessor Technology Ltd.
The EMC²-ZU3EG is a PCIe/104 OneBank™ SBC with a Xilinx Zynq SoC and a VITA57.1 FMC™ LPC I/O board. The main processing power of the EMC²-ZU3EG is a Dual Core ARM9 and combined with traditional FPGA fabrics/gates + High-Speed I/O interfaces, like USB2.0, HDMI, 1Gb Ethernet and SATA and provide an total solution for any Embedded Application.
-
product
6U VPX UltraScale™ FPGA board with FMC+ sites
IC-FEP-VPX6e
Based on the latest Xilinx Kintex UltraScale™20nm FPGA, the IC-FEP-VPX6e is a 6U OpenVPX Front-End Processor (FEP) optimized for applications requiring DSP intensive processing in highly constrained environments.
-
product
VME PowerPC Single Board Computer
DP-VME-0405
The DP-VME-0405 is a high performance VME PowerPC single board computer(SBC) that features the latest PowerPC 7410, SDRAM with error detection and correction and a dedicated L2 cache bus. The board's architecture strikes a balance between high performance processing power, memory and I/O resources. With its vast array of interfaces, the DP-VME-0405 allows the user to perform intensive I/O while permitting rigorous computing. Two industry standard PMC slots enhance the I/O capability, allowing the users to provide program specific features by using commercially available PMC module.
-
product
PMC Analog Out Board
MS 1821
*Bus Interface:- 32 Bit PCI Bus with PMC Interface*Speed of operation up to 66MHz*Spartan-3AN FPGA based design*32 channel single ended analog Output*Unipolar or bipolar voltage output*Programmable output voltage: 0-5V, 0-10V, 0-10.8V, ±5V, ±10V, ±10.8V and is capable of driving up to +/-20mA*16 bit Resolution*Conversion time 10usec typ*Over current protection*Driver interface for Windows2000/XP/VISTA and LINUX OS*Self Test future
-
product
System Synchronizer and Distribution Board - VME
Model 6891
Model 6891 System Synchronizer and Distribution Board synchronizes multiple Pentek I/O modules within a system. It enables synchronous sampling and timing for a wide range of multichannel highspeed data acquisition, DSP and software radio applications
-
product
3U VPX Processor Board
VP32001
LinkedHope Intelligent Technologies Co.,Ltd.
The VP32001 is a PC-compatible high performance 3U VPX processor board supporting the 2nd generation Intel® Core™ processor and the Intel® Series 6 mobile class chipset with up to 8 Gbytes of DDR3-1333 ECC SDRAM. The VP32001 features an XMC site and a range of I/O interfaces including two SATA600 channels, dual 1000Base-BX, RS232/422/485 and USB interfaces. The board provides a flexible PCI Express® (PCIe) backplane fabric interface that can be configured in several ways from eight x1 PCIe ports to a single x8 PCIe port making it suitable for use in both distributed systems and centralized switching systems as defined in OpenVPX (VITA 65). For rugged applications two VPX-REDI conduction-cooled versions are available, the VP32001-RCS is a VPX-REDI Type 1 Two-Level Maintenance conduction-cooled board and the VP32001-RCT is VPX-REDI Type 2. The board is suitable for a range of applications within industrial control, transport, aerospace, security and defense applications. To simplify integration many standard operating systems are supported.
-
product
DVI Extender with IR and Stereo Audio Options via One CAT5/6/7
ST-C6DVI-300
The XTENDEX® DVI Extender transmits digital DVI video up to 300 feet away from a DVI source over a single CAT5/6/7 cable. Each video extender consists of a local unit that connects to a single link digital DVI source and optional IR emitter, and a remote unit that connects to a DVI display and optional IR receiver.
-
product
PC104 MIL1553A & MIL1553B Board
MS 1701
*Bus Interface - Standard ISA Bus (PC104 Interface)*One Dual Redundant MIL-STD-1553 Channels, Enhanced Mini-ACE BC/RT/MT Architecture*A periodic message insertion, Real-time bus playback with RT edit mode*Highly Autonomous Bus Controller Architecture, Message Scheduling*Bulk Data Transfers, Data Block Double Buffering*Asynchronous Messages, Retries and Bus Switching*Transformer or Direct Coupled 1553B Channels
-
product
ABex Terminal Module for Extending the Functionality of the PXI-501
ABex TM-501 MFI
The ABex TM-501 is an ABex terminal module that extends the multifunction measurement card PXI-501 with additional features. It is located in front of the PXI-501 card.It expands the analog outputs voltage range of the PMUs to -10V up to +40V. Additionally it features a shunt current measurement unit to measure currents up to 500mA
-
product
Board
ARINC-708
The Weather Radar protocol consists of 1600-bit ARINC-708 words, which, when interpreted and plotted together, form a picture of weather patterns in the surrounding area. The various weather conditions are indicated by the colors displayed.
-
product
PC/104 OneBank Board
EMC²-7K325
Sundance Multiprocessor Technology Ltd.
The PCIe/104 OneBank™ design enables the EMC²-7K325 to be added to robust and rugged installations for various commercial, medial, industrial and military uses and to enable more versatility the EMC²-Kintex7T also incorporates a VITA57.1 FMC™ LPC connector opening up an range of extra possibilities and expansion options
