Serial
a bus that can be used with almost any device transmitting a single stream of data.
See Also: Bus, Parallel, I2C, LIN, Can bus, ExpressCard, Fieldbus, FireWire, RS-232, RS-485, PCI Express, Serial ATA, Serial Peripheral Interface, SMBus, Serial Analyzers, Serial Digital Interfaces, Serial Communications, Serial Data
-
Product
Stand-Alone Doppler Current Sensor
DCPS
-
The Doppler Current Profiler Sensor (DCPS) is a medium-range, 600kHz current profiler smart sensor. It offers high-quality ocean current measurements and is ideally suited for cabling directly to various systems or dataloggers via serial or AiCap bus. With its integrated compensation for tilting and movement, the sensor is commonly used to measure current from buoys and other moving platforms.The 5400/5400R version of the current sensor is 300m depth rated, the 5402/5402R version is 4500m depth rated, and the 5403/5403R version is 6000m depth rated and intended for commercial as well as research use. It comes with an integrated temperature sensor that can be calibrated on request.As an extension to the DCPS, we now offer the current profiler with an integrated pressure unit called the 5400P. This version enables acoustic wave measurements in addition to profiling currents. Ideal for small observatories, the DCPS sensor is the market's lowest-cost current and wave sensor.
-
Product
1 GHz A/D and D/A with Virtex-6 FPGA - XMC
Model 71630
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- One 1 GHz 12-bit A/D- One 1 GHz 16-bit D/A- Up to 2 GB of DDR3 SDRAM or 32 MB of QDRII+ SRAM- Sample clock synchronization to an external system reference- Front panel clock/sync bus for multimodule synchronizationPCI Express (Gen. 1 & 2) interface up to x8 wide- Optional user configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Synchronize up to four modules with Model 7192 System Synchronization and Distribution Amplifier - PMC/XMC- Synchronize up to twelve modules with Model 9192 System Synchronization and Distribution Amplifier- 1U Rack-mount
-
Product
Altitude Data Simulator
ADS-100
-
The Model ADS-100 is an all solid-state device that simulates the output of altitude encoders/digitizers in both parallel and serial (RS232) data formats. Designed to substitute for an altitude encoder when testing and troubleshooting an aircraft's altitude reporting system, the ADS-100 provides two RS-232 compliant outputs in addition to the ICAO pressure altitude code.
-
Product
L-Band RF Tuner and 2-Channel 500 MHz A/D with Virtex-7 FPGA - XMC
Model 71791
-
- Accepts RF Signals from 925 MHz to 2175 MHz- Programmable LNA handles L-Band input signal levels from -50 dBm to +10 dBm- Programmable analog downconverter provides IF or I+Q baseband signals at frequencies up to 123 MHz- Two 500 MHz 12-bit A/Ds digitize IF or I+Q signals synchronously; optional: 400 MHz 14-bit A/Ds- Two FPGA-based multiband digital downconverters- Xilinx Virtex-7 VX330T or VX690T FPGAs- 4 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- PCI Express (Gen. 1, 2 & 3) interface, up to x8- Clock/sync bus for multimodule synchronization- VITA 42.0 XMC compatible with switched fabric interfaces- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-7 FPGA for custom I/O
-
Product
Data Acquisition (DAQ) Software - Dewesoft X
-
Data Acquisition (DAQ) SoftwareDewesoft has been developing leading data acquisition (DAQ) software for more than 20 years. Dewesoft X is the world's best data acquisition (DAQ), data recording, and data analysis software.The software received multiple international awards, is innovative, very easy to use, and requires no programming to acquire, store and analyze data synchronized from several data sources - analog, digital, CAN, CAN FD, CXP, GPS, video, serial and many other data interfaces.Our DAQ software is included for free to all of our data acquisition systems and we offer FREE support and FREE software upgrades forever. No hidden costs. Using our software is easier than riding a bike and has been trusted for years by the world's biggest brands like NASA, Space X, Airbus, Boeing, General Motors, Audi, Ferrari, VW, Tesla, Honda, Toyota, Caterpillar, John Deere to name just a few.
-
Product
1553Guard
-
MIL-STD-1553 bus architecture is a threat that adversaries can leverage to compromise your equipment and spread malicious software through your Serial Data Bus (SDB) system. You need a solution that can not only identify current and future cyberattacks in real-time but also instantly eliminate those threats before they wreak havoc and interrupt the mission.
-
Product
A Serial Data Link Monitor for Windows
Listen
-
Listen is a Data Link monitor designed to assist debugging & troubleshooting serial communications links. Listen utilizes standard Windows COM port drivers to tap into RS-232 transmit signals for monitoring bi-directional communications between two devices.
-
Product
Temperature Logger with Integral sensor and Probe
TV-4510
-
Dual channel temperature recorder LCD display of current readings 30,000 readings capacity High accuracy and reading resolution Fast data offload Splashproof case Low battery monitor and battery low indicator Programmable alarms Optional audible alarm box USB and serial download cables
-
Product
PCI Express VXIbus Slot-0 Interface
ProDAQ 3030
-
The ProDAQ 3030 PCI Express VXIbus slot-0 interface is a C-size, register-based VXIbus module providing a direct connection from a PC to a VXIbus mainframe using the high-speed PCI Express serial bus. Together with any of the available host cards, the ProDAQ 3030 enables users to use a laptop, desktop, or server computer as an embedded controller. Optimized for low latency and high throughput, it provides a high-performance but cost-effective solution for a data acquisition system.
-
Product
4-Channel 200 MHz A/D with Multiband DDCs, Kintex UltraScale FPGA - 3U VPX
Model 52862
-
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Complete radar and software radio interface solution- Supports Xilinx Kintex UltraScale FPGAs- Four 200 MHz 16-bit A/Ds- Four wideband DDCs and- 32 multiband DDCs (digital downconverters)- 5 GB of DDR4 SDRAM- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multimodule synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x4- Optional LVDS and gigabit serial connections to the FPGA for custom I/O- Compatible with several VITA standards including: VITA-46, VITA-48 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
Multiprotocol Serial Card
LPCI-COM-8SM
-
The LPCI-COM Series are eight or four-port asynchronous serial communication cards designed for use in PCI bus computers. The cards support RS-232, RS-422, and/or RS-485 communications which can be selected on a port by port basis. The cards are 6.6 inches in length and 2.21 inches seated height and may be installed in any 3.3 or 5-volt PCI or PCI-X expansion slot.
-
Product
Ethernet/AFDX/BroadR-Reach PXI Fault Insertion Switch - 4 Channel
40-201-004
Fault Insertion Unit
This high bandwidth differential fault insertion module is designed to simulate common faults on high speed two wire communication interfaces such as Ethernet. This module supports 4 or 8-channels of two wire serial connections and can be used for simulating faults on Ethernet, AFDX, BroadR-Reach, 100BaseT and 1000BaseT interfaces. Any wire can be set to an open circuit, shorts can be applied across the wire pair, or to the adjacent pair. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to a supply voltage or ground. Each fault bus is capable of carrying 2A allowing multiple channels to be connected to the same fault condition. Additionally, each fault bus features a changeover relay to allow the user to connect alternative fault conditions to the fault buses.
-
Product
FPGA Mezzanine Card
FMC168
Digitizer
The FMC168 is a digitizer FMC featuring eight ADC channels with 16-bit resolution and 250Msps sampling rate per channel.With a flexible clock generation and distribution scheme, the FMC168 allows control of sampling frequency and analog input gain through serial communication with a carrier card.
-
Product
Modbus Module Test Tool Software
ModTest
-
Modtest 2 software allows the configuration and settings of a Rotork Modbus Module Mk2 inside an individual actuator to be carried out easily and simply over the data bus. In addition, the actuator can also be exercised using this PC based software. The Modtest 2 software is used for diagnostic and maintenance of a Modbus controlled actuator over a serial link from the PC.
-
Product
Silicon Oscillators
-
Analog Devices silicon oscillators are frequency programmable via pin-strapping, or through the resistor connection or serial interface (SPI or I2C). These solid-state clocks are well-suited for general-purpose usage, such as PGAs, ASICS, microprocessors, or UARTS, and they operate from 1 kHz to 170 MHz. Silicon oscillators are also ideal switching regulator clocks as they provide synchronization and EMI reduction (via spread spectrum).
-
Product
CANbus Controller Standard Interface
PCI360
-
The PCI360 CANbus controller PCI card is based on the SJA1000. The SJA1000 provides an interface to the popular CANbus that support both standard (11-bit) and extended (29-bit) identifier messages. LEDs provide diagnostics information.The CAN network is a serial communication protocol which efficiency supports distributed real-time control with a high level of reliability.
-
Product
Mixed Signal Oscilloscope, 1 GHz 2 Analog Plus 16 Digital Channels
MSOX3102A
Oscilloscope
1 GHz2 analog plus 16 digital channels Easily view your signals on the 8.5-inch WVGA display Capture more data with up to 4 Mpts memory See more signal detail with 1,000,000 wfms/s update rate Expand your measurement capabilities with full upgradability: Add memory, 20 MHz arbitrary waveform generator, 3-digit voltmeter, serial trigger and analysis, segmented memory & mask testing at any time
-
Product
10 Gb/s SFP/SFP+ Evaluation Board
EV-SFP-171
-
The purpose of this SFP+ evaluation board is to provide the designer with a convenient means for evaluating SFP+ fiber optic transceiver such as 10 Gb/s(up to 16 Gb/s) SFP/SFP+ transceiver compliant with ANSI Fibre Channel FC‐PI‐5 for high speed electrical and optical specifications. This board provides SMA connectors for high speed TX and RX signals. The low speed control signals such as Tx_Fault, Rx_LOS and Rate_Selects can be controlled by using on board switches and test points. A connector for 2 wire serial interface to the module is also provided.
-
Product
Automatic Span Gasgenerator Unit
ASGU-370 Series
-
The multi point calibration units ASGU-370 series is designed for simultaneous (parallel) or step by step (serial) checking of gas analyzers. It is primarily installed in laboratories for quality assurance and is also used for the production of gas analyzers.Furthermore are the calibration units as a Transfer standard in portable suitcase available. Here we have for ongoing quality control in field the versions all in one aluminum suitcase and for a flexible and back-friendly wearing comfort the ASGU-370TS SPLIT.
-
Product
3U CompactPCI Serial 4-slot SSR w/o RTM w/ Ethernet
1CPCIS-304-R200
-
3U CompactPCI Serial Backplane with 4 CompactPCI S.0 slots, system slot right, without rear IO : 1x CompactPCI S.0 CPU slot, 3x CompactPCI S.0 peripheral slots, without connectors for RTMs (RearTransition Modules), Ethernet full mesh.
-
Product
In-System Programmers
-
Xeltek in-system programming tools provide a convenient method for configuring microcontrollers and various serial devices. Users could simply program microcontrollers, Flash memories, PLDs, and FPGAs via the ISP cable. Devices are programmed in the target system or target hardware, making field applications more convenient than ever. Typically, a jumper/DIP switch enables in-system programming and a set of serial programming connector (such as an IDC connector) connects the target board(s) to the ISP programmer(s).
-
Product
PXI 32 Chan I/O Parallel I/P Prog Threshold
40-412-111
Digital I/O
A 32-channel Digital I/O module with high output voltage and currentcapability and a dual variable threshold input. Each of the 32 channel outputs can be used to drive the output high or low usinga high current capacity drive capable of sourcing 0.4A from the high side or 0.5Asink on the low side for each channel. The module is available in two versions witheither serial or parallel capture of the input levels.
-
Product
Absolute Length Gauges For Measuring Stations And Multi-gauging Fixtures
ACANTO series
-
*High system accuracy: ±2 µm / ±1 µm*Serial data transmission*Interface: EnDat 2.2*Protection rating of up to IP67*Compact design for limited installation space*Various plunger actuation possibilities
-
Product
RS232 Null-Modem Cable, DB-9 Female to DB-9 Female, 2m
182238-02
Serial Cable
9-Pin Female DB-9 to 9-Pin Female DB-9 Serial Cable - The 9F-9F Serial Cable, sometimes referred to as GPIB Serial Cable, connects and controls GPIB devices using RS232 and RS485 serial ports. The 9F-9F Serial Cable is offered in different lengths.
-
Product
GPIB-RS232, Instrument Control Device - Japan 100VAC
779732-07
GPIB Controller
The GPIB‑RS232 is an IEEE 488 controller device for computers with an RS232 port. You can use this device to integrate an instrument into your system using GPIB. This device transforms a computer with an RS232 serial port into a talker, listener, or controller on the GPIB bus. It can also interface RS232 instruments and peripherals to the GPIB bus. It can implement the physical and electrical specifications of the IEEE 488 and RS232 standards, as well as interpret and execute high-level commands from the serial port, including RS232‑to‑GPIB and GPIB‑to‑RS232 protocol conversions. This device is IEEE 488.2 compatible. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
Product
Oscilloscope - 350 MHz, 2 Analog Channels
DSOX3032T
Oscilloscope
350 MHz2 analog channels Easily view and analyze your signals with on the large 8.5-inch capacitive touch screen Isolate signals in seconds with exclusive Zone touch triggering See more signal detail with the 1,000,000 wfms/s update rate Capture more data with up to 4 Mpts memory Expand your measurement capabilities with full upgradability: Add bandwidth, digital channels, 20 MHz arbitrary waveform generator, 3-digit voltmeter, serial trigger and analysis & mask testing at any time
-
Product
Linear Power Supplies Programmable, Digital Control, Rack Mount, Ultra Low Ripple/Noise
Series MAT
-
Kepco MAT are linear power supplies that are oriented to systems applications. Their principal control means is a 2-wire, long range, serial bus, Kepco's single address, multiple instrument bus. As many as 27 power supplies, including models in the Kepco MST, MBT and BOP series may be "daisy-chained" on this bus and interfaced either to IEEE 488.2, a PC bus, or to a VXI host.
-
Product
Intelligent Interface Card
IIB-1553-PCI-2C
-
The IIB-1553-PCI-2C provides an intelligent interface card for two serial, dual redundant MIL-STD-1553 data buses and the PCI bus. The card supports 1553A, 1553B, McAir and STANAG 3838 variants on a single card. The IIB-1553-PCI-2C provides concurrent Bus Controller (BC) and up to 31 Remote Terminals (RT) with Bus Monitor (BM). An additional stand-alone Chronological Bus Monitor (CBM) facility is also provided, with comprehensive multi-level triggering capability. Full error injection capability is provided in BC and RT modes, with full error detection in BC, RT, BM and CBM modes. Two independent variable amplitude dual redundant 1553 interfaces are provided, each with2 Mbytes of dual ported RAM. The board is supplied with C drivers in source code and Windows menu driven software as standard.
-
Product
PCI-104 8-Port, 4-port, And 2-port Multi-Protocol RS-232, RS-422, RS-485 Serial Communication Boards
104i-COM-8SM Family
-
The 104i-COM-8SM (PCI-104) family of multi-port, multi-protocol (RS-232, RS-422, RS-485), serial communication boards deliver up to eight high-speed serial communication ports for use in a wide variety of applications. The boards were developed for use by system integrators and manufacturers in the design of industrial and commercial systems. Based on the XR17D158, the boards have eight enhanced 16550 UARTs, each with a set of modem signals (CTS, RTS, RI, DTR, DSR, CD) in RS-232 mode.
-
Product
Emulates Atmel AT89C51SND1
FE-SND1
-
* Emulates Atmel AT89C51SND1 * 62K Code Memory * Real-Time Emulation * Frequency up to 20MHz/3V * ISP and X2 Mode Support * MS-Windows Debugger For C And Assembler * Emulation Headers and Signal Testpoints * Programmer Included * Serially Linked to IBM PC at 115Kbaud
