Prototyping
Construction of first working designs.
-
Product
400 MHz to 4.4 GHz, GPS-Disciplined OCXO, Reconfigurable USRP Software Defined Radio Device
783927-01
Communications Module
400 MHz to 4.4 GHz, GPS-Disciplined OCXO, Reconfigurable USRP Software Defined Radio Device - The USRP-2952 provides an integrated hardware and software solution for rapidly prototyping high-performance wireless communication systems. Built on the LabVIEW reconfigurable I/O (RIO) architecture, USRP RIO delivers an integrated hardware and software solution, so researchers can prototype faster and shorten time to results. You can prototype a range of advanced research applications that include multiple input, multiple output (MIMO); synchronization of heterogeneous networks; LTE relaying; RF compressive sampling; spectrum sensing; cognitive radio; beamforming; and direction finding. The USRP-2952 is equipped with a GPS-disciplined 10 MHz oven-controlled crystal oscillator (OCXO) reference clock. GPS disciplining delivers improved frequency accuracy and synchronization capabilities.
-
Product
USRP Software Defined Radio Stand-Alone Device
-
The USRP Software Defined Radio Stand-Alone Device consists of an onboard processor, FPGA, and RF front end. You can program this device using either LabVIEW Communications System Design Suite or an open-source software workflow, depending on the operating system you choose. You can provision the device with NI Linux Real-Time, Linux Fedora, or Linux Ubuntu real-time operating systems. The USRP Software Defined Radio Stand-Alone Device enables you to prototype a range of advanced research applications such as stand-alone LTE or 802.11 device emulation; Medium Access Control (MAC) algorithm development; multiple input, multiple output (MIMO); heterogeneous networks; LTE relaying; RF compressive sampling; spectrum sensing; cognitive radio; beamforming; and direction finding.The registered trademark Linux® is used pursuant to a sublicense from LMI, the exclusive licensee of Linus Torvalds, owner of the mark on a worldwide basis.
-
Product
NI-9861, 1-Port, Low-Speed/Fault Tolerant C Series CAN Interface Module
781962-01
CAN Interface
1-Port, Low-Speed/Fault Tolerant C Series CAN Interface Module—The NI‑9861 is a fault-tolerant Controller Area Network (CAN) interface for developing applications with the NI‑XNET driver. The NI‑9861 is ideal for applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. You can perform this manipulation while taking other data acquisition measurements in the same NI CompactDAQ hardware platform or while performing low-level FPGA control and embedded monitoring in the same NI CompactRIO chassis.
-
Product
Boundary Scan Program Development Service
-
No need for test fixtures. Integrates product development, production test, and device programming in one system. Test and Programming data can be reused in Production. Fast test procedure development. Reduced inventory management. Eliminates or reduces ICT usage time. Pre-production testing can begin as soon as prototype is released.
-
Product
Open Frame Panel PC
-
By highly flexible configuration with a high level of modularization, ADLINK's Open Frame Panel PC, leveraging Intel® x86 and NXP ARM-Based solutions, with ready-to-use design helps system integrators, integrated solution providers, and brand vendors quickly deliver cutting-edge functions to individual HMI applications. Leveraging our unique Function Module (FM) design, these industrial panel PCs accelerate prototyping according to the application's requirements while saving considerable time, money, and effort. The SP2 series is ideal for industrial automation, transportation, retail, healthcare, gaming, and other industries.
-
Product
Prototype /Short Run Production
-
We make high precision Prototype /Short Run Metal Stampings & Machined Components.We have been successfully serving industrial clients, mostly OEM Automotive Suppliers, since 2005. We have the ability to take your CAD model and turn it into Production Representative Parts within days.
-
Product
LIN Interface Module
C- Series
LIN Interface
C Series LIN Interface Modules are bus interfaces for developing applications with the NI-XNET driver. The NI-XNET device-driven DMA engine couples the LIN bus to host memory to minimize message latency. You can import, edit, and use signals from LDF databases in integrated LIN databases. C Series LIN Interface Modules work well for applications requiring real-time, high-speed manipulation of many LIN frames and signals, such as hardware-in-the-loop simulation, rapid control prototyping, bus monitoring, and automation control.
-
Product
CMX RF Port Extender
CMX-Z25
-
Complex devices under test (DUT) come with additional antenna ports to support low, mid and high bands - and advanced MIMO schemes such as 4x4 MIMO. The R&S®CMX-Z25 is the solution: Up to 16 DUT ports can be supported with just 4 ports from R&S®CMX500. So even prototypes of 5G smartphones, tablets, laptops or industrial modules with an extended number of antenna ports can now be connected to a single R&S®CMX500. Together with the scalable CMX architecture any 5G and 5G Advanced mobile device can now be tested in one go - without recabling or 3GPP band combo limitations.
-
Product
RTAX/RTSX Netlist Converter
-
RTAX/RTSX EDIF and PDC/PIN Converter combines two functions supporting Aldec RTAX prototyping - it provides EDIFs netlists conversion and PDC/PIN constraints file remapping for two families RTAX-S/SL and RTSX-SU/S, SX-A. RTAX/RTSX EDIF and PDC/PIN Converter performs automatic conversion of the RTAX-S/SL and RTSX-SU/S, SX-A EDIFs netlists to ProASIC3/E EDIF netlist, which means replacement of the PLL and memory primitives has to be done, with consideration of the limitations caused by the differences between RTAX-S/SL, RTSX-SU/S, SX-A and ProASIC3/E technologies.
-
Product
RF Prototyping Kit
VXI-5501
-
* VXI-5501 has a Bare Copper-clad Prototyping Board for RF and microwave modules.* Includes a VXI-5524 Register Based Interface Board with 48 digital IO lines and a 16-bit VXI data bus.* User configurable model number, manufacturer ID, version and serial numbers identifies the module as from your company.* Includes a blank front panel, side shields, manual, layout aids and VXI-Kit hardware for a single slot wide C-size module.
-
Product
2-Slot 64-bit 6U CompactPCI Backplane
cBP-6402
Backplane
ADLINK offers a wide selection of standard backplanes from single up to 20 slots. Furthermore, a professional OEM team is capable of custom backplanes with a quick turnaround tailored to your specifications. We make designing, developing, prototyping, and maintaining your projects simple & efficient. For all your backplane needs, give us a call, we have a solution for you.
-
Product
Prototyping Service
-
Not sure if your new idea is going to work? Come and talk to us. We have a lot of experience in developing proof-of-concept benchtop systems. Remember, it’s not a “lash-up”, it’s the “first step in your product development cycle”. The picture shows a prototype double-pass spectrometer (on the left) that was built into a portable, robust benchtop unit (on the right).
-
Product
RF/MicrowavePrototyping Boards and Housings
MicroAmp2
-
MicroAmp2 is a new series of RF/microwave prototyping boards and housings that allow for rapid construction of custom circuits in a fraction of the time and cost of traditional solutions. With the MicroAmp2 series of MB boards, a designer can quickly build amplifiers, filters, passive networks, multipliers, prescalers, log detectors, oscillators, and opamps using many popular components. A growing line of MB circuit boards are available to fit many of the industry-standard components, which can be easily assembled and mounted into shielded RF housings to create fully functional modules. Select parts from popular manufacturers such as Analog Devices, Avago, CEL, M/A-COM, Mini Circuits, RFMD, Triquint, and others.
-
Product
Terminal Block
Terminal Block
The Terminal Block provides standard back-end connector types, such as BNC, D-SUB, VHDCI, and more. Some models offer screw pin terminals for the front-end connectors as well as different mounting options including DIN vertical rail, DIN horizontal rail, wall, panel, or module. You can use terminal blocks for connecting analog or digital signals, generating signals, prototyping, performing custom circuitry, and more.
-
Product
Customized Solutions
-
Artifex Engineering GmbH & Co. KG
Our products form the basis of a wide range of R&D and industrial metrological applications. At Artifex Engineering we strive to maintain a close relationship with our customers to ensure that the products we deliver meet your needs cost effectively. We understand that your application is not standard and so we offer customization of all of our products, even for single units. Our manufacturing infrastructure includes rapid prototyping machinery and a flexible manufacturing environment allowing us to customize quickly and efficiently – a definite pricing advantage.
-
Product
GHz Elastomer Sockets
-
Ironwood’s GHz BGA & QFN/MLF sockets are ideal for prototyping and testing almost any BGA or QFN device application. These ZIF sockets provide excellent signal integrity yet remain cost effective. Innovative elastomer interconnect technology that delivers low signal loss up to >40GHz and supports BGA or QFN/MLF pitches down to 0.3mm was utilized in these sockets. GHz BGA sockets are mechanically mounted over a target system’s BGA lands using mounting and alignment holes at proper locations (page 2 of the individual socket drawing shows recommended PCB layout information). These low-profile sockets are only 2.5 mm per side larger than actual IC packages (industry’s smallest footprint). They support IC devices with body sizes ranging from 55mm down to 1mm. Larger body sizes may require a backing plate. If the backside of the target PCB contains capacitors and resistors, a custom insulation plate with cavities cut for those components can be designed. This insulation plate sandwiches between the backing plate and target PCB.
-
Product
PXIe-5763, 16-Bit, 500 MS/s, 4-Channel PXI FlexRIO Digitizer
785161-01
FlexRio Digitizer
The PXIe-5763 is a PXI FlexRIO Digitizer that simultaneously samples four channels at 500 MS/s with 16 bits of resolution and features 225 MHz of analog input bandwidth. With over 73 dB of SNR, the PXIe-5763 is ideal for applications that require a wide dynamic range with a wideband digitizer. The FlexRIO driver includes support for finite and continuous streaming modes, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale FPGA. Available in AC and DC coupled variants, the PXIe-5763 is ideal for both time and frequency domain applications, including radar prototyping, LIDAR, communications, microscopy, OCT, event detection, and particle physics.
-
Product
PXIe-5763, 16-Bit, 500 MS/s, 4-Channel PXI FlexRIO Digitizer
785164-01
FlexRio Digitizer
The PXIe-5763 is a PXI FlexRIO Digitizer that simultaneously samples four channels at 500 MS/s with 16 bits of resolution and features 225 MHz of analog input bandwidth. With over 73 dB of SNR, the PXIe-5763 is ideal for applications that require a wide dynamic range with a wideband digitizer. The FlexRIO driver includes support for finite and continuous streaming modes, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale FPGA. Available in AC and DC coupled variants, the PXIe-5763 is ideal for both time and frequency domain applications, including radar prototyping, LIDAR, communications, microscopy, OCT, event detection, and particle physics.
-
Product
Universal 3D Metrology Software Platform
PolyWorks
-
Defining the cutting edge of 3D metrology, the PolyWorks software suite maximizes productivity, quality, and profitability when integrating 3D measurement technologies into an industrial manufacturing process. From part and tool design and prototyping down to final inspection of assembled products, PolyWorks offers advanced solutions to cover the complete product development cycle. Interfacing directly with major brands and technologies of single-point and point cloud 3D measurement devices through plug-in extension modules, this universal platform also supports a wide array of native point cloud and polygonal model file formats.
-
Product
Lithography Systems
-
When it comes to shaping what a chip can do, lithography systems lead the way by transferring intricate circuit designs onto substrates with unmatched precision. From prototyping to high-volume manufacturing, these tools define the geometry of modern microchips, as well performance.
-
Product
SparkFun Solder-able Breadboard
Large
-
This is the Large SparkFun Solder-able Breadboard. A bare PCB that is the exact size as our full-size breadboard with the same connections to pins and power rails. This board is especially useful for preserving a prototype or experiment you just created on a solderless breadboard by soldering all the pieces in place.
-
Product
Custom Ultrasonic Transducers
-
Blatek ultrasonic transducers are designed to meet custom apecifications using our proprietary piezocomposite. We take pride in our ability to design and manufacture ultrasonic probes to the exact design our customers provide. Our staff is experienced in working with customers through the transition from prototype to product. We have produced phased array, linear array, and curved linear array transducers, all with broad bandwidth, high sensitivity, and excellent element to element uniformity.
-
Product
3D Scanning Software
-
Software is a comprehensive component to any advanced metrology system. Combined with laptops and portable equipment, 3D scanning and measurement is now possible virtually anywhere. 3D scanner software plays a critical role in every stage from the creation of a concept design to the manufacturing and inspection of prototypes. Below is a look at some of the Laser Scanner Software and 3D Scanner Software providers and platforms we represent and handle.
-
Product
COM Express Type 6 Prototyping Kit based on Intel® 12th Gen Core™ i5-12600HE
COM Express Type 6 Alder Lake-P
Computer on Module
The cExpress-BT is a COM ExpressR COM.0 R2.1 Type 6 module supporting the Intel Atom® processor E3800 Series and Intel® Celeron® N2900/J1900 processor SoC (codename: Bay Trail). The cExpress-BT is specifically designed for customers who need high-level processing and graphics performance with low power consumption in a long product life solution.
-
Product
SSOP-to-DIP Adaptor
Series 651000
-
SSOP IC to DIP Adapter. Allows the use of .65mm pitch surface mount ICs in thru-hole designs. Ideal for prototyping and testing/evaluating SSOP ICs. Adapter can be cut to smaller sizes by end user. Consult factory for panelized form or for mounting of consigned ICs.
-
Product
PCI-8512, 1‑Port, High‑Speed/FD CAN Interface Device
780683-01
CAN Interface
The PCI‑8512 is a high-speed controller area network (CAN) flexible data-rate (FD) interface for developing applications with the NI‑XNET driver. The PCI‑8512 excels in applications requiring real‑time, high‑speed manipulation of hundreds of CAN frames and signals such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex models and applications.
-
Product
Electronics Manufacturing Services
EMS
-
A production consignment service that develops based on know-how and technological capabilities of "MONOZUKURI " that we have cultivated over many years. Full support from design to board mounting, prototyping, manufacturing, maintenance. We respond to various outsourcing needs such as customer's design consignment and production consignment.
-
Product
PCI-8517, 2-Port FlexRay Interface Device
780685-02
Interface
2-Port FlexRay Interface Device—The PCI‑8517 is designed for developing FlexRay applications. As part of the NI‑XNET platform, the PXI‑8517 works well in applications requiring real-time, high-speed manipulation of hundreds of FlexRay frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The PCI‑8517 contains two fully functional FlexRay interfaces, allowing an individual engine control unit (ECU) to be connected to the interface when other cold-start nodes are not available. You also can use the interfaces individually to connect two separate FlexRay networks while maintaining full performance on each interface.
-
Product
PLD Systems
Pulsed Laser Deposition
-
Is a versatile thin film deposition technique. A pulsed laser (~20 ns pulse width) rapidly evaporates a target material forming a thin film that retains target composition. This unique ability of stoichiometeric transfer of target composition into the film was realized first by the research team led by Dr. Venkatesan at Bell Communications Research, NJ, USA, nearly 30 years ago while depositing high temperature superconducting (YBa2Cu3O7) thin films. Since then, PLD has become the preferred deposition technique where ever thin films of complex material compositions are considered. Another unique feature of PLD is its ability for rapid prototyping of materials. The energy source (pulsed laser) being outside the deposition chamber, facilitates a large dynamic range of operating pressures (10-10 Torr to 500 Torr) during material synthesis. By controlling the deposition pressure and substrate temperature and using relatively small target sizes, a variety of atomically controlled nano-structures and interfaces can be prepared with unique functionalities.
-
Product
DIP Adaptor
-
48Pin .5mm QFP to 48Pin .6 Dip Adapter. Makes 48 pin QFP prototype circuits with a standard bread board easy.
