Power Sources
Supply stable and consistant electrical or light energy.
-
Product
Source Systems AC
-
The power sources of MTS-series based on digital amplifier modules combined with frequency generator and reference device are the MTS source system. Single-phase systems (MTS1xx) or three-phase systems (MTS3xx) from 1 to more than 40 test positions are available.
-
Product
AC Power Source Control And Data Capture Software
PowerTRAC™
-
Program and run your power source remotely via PC. Easily gather data and analyze test results like never before.
-
Product
Pulse Laser
-
Is a variable, pulsed high power laser source, a building block ideal for MOPA, LIDAR, OTDR laser systems development and applications. This fully integrated compact module contains a Distributed Feedback (DFB) laser and built-in optical amplifier stage, and a variable nanosecond pulse generation circuits. It provides up to 200 mW optical peak power in 1064 nm wavelength region, with a programmable pulse width from 10 ns to 1000 ns, and a selectable pulse repetition rate from 100 Hz to 1 MHz The optical pulse generation can alternatively be controlled via an external electrical trigger. In a compact design, NPL-CWDM-M is applicable for OEM integration or as a stand alone pulsed laser source. Contact Optilab for more information.
-
Product
Syscal R1 Plus Switch
-
The SYSCAL R1 Plus resistivity meter is specifically designed for medium-depth exploration. It combines a power source, transmitter up to a 200W or 1200Vpp output voltage, and a 2 channels receiver in a single unit; its compactness makes it an effective tool for intensive resistivity surveys.
-
Product
Multiple (8) High Power Four Quadrant Power Source
PM0825
-
The PM0825 consists of 8 fully independent four-quadrant power sources capable of supplying up to ±20V. Two of the sources are capable of up to 500mA each, four more are capable of performing at low levels with ranges of 1uA and 100uA; the remaining two are mid range with current ranges of 1mA and 100mA.
-
Product
Sweep Generator
G440XE
-
The G440XE Sweep Generators are portable powerful wideband general-purpose sources for swept and CW microwave measurements in local or remote operation modes. It incorporates the efficiency of micro-processing control with state-of-the-art BWO oscillator to produce a high performance sweep generator system suited for either manual or automated measurements.
-
Product
PoE Voltage Monitor Detect & Verify
PE-400
-
PE-400 is specific to test and verify PSE or Ethernet outlet either a standard/active PoE or a NON-standard/passive PoE to avoid damaging Non-PoE device as well as monitor and display available Voltage simultaneously. It built-in PoE interface controller to trigger on 802.3 af, at and bt switch and verify standard PoE type either 802.3 af or 802.3 at, and power source either End or Mid or both, and power polarity as well as display voltage values. The operational voltage which should be measured when installing a new PoE system or when you troubleshooting an existing system.
-
Product
Full 4-Quadrant Grid Simulator
TC.ACS
-
The increasing number of alternative power sources like solar, wind driven or biological energy systems call for consistent and well demanding regulations for energy feed into the utility grid. Manufacturers of such systems have to test and to prove the compliance of their equipment. Grid simulators form an electronic equivalent circuit for the grid, but allow to vary all relevant parameters in order to test the behaviour and response of the equipment under test.
-
Product
AC Power Source
APS-7000 Series
-
AC Power Source APS-7000 Series, the advanced direct digital frequency synthesizer (DDS) waveform is used to achieve high frequency stability, good continuity and accurate measurement.
-
Product
Power Dividers & Splitters
-
Keysight dividers and splitters are used in a wide range of applications, such as: transmission line fault testing, power combining, source leveling, ratio measurements, power splitting, and critical signal processing applications that require minimal insertion loss and high port isolation.
-
Product
PoE Power Sourcing Equipment For TBOX300/tBOX400/tBOX500 Series
PSU120-259
-
*M12 5P DC input*Terminal block PoE power output, maximum 120W*Designed for tBOX300/tBOX400/tBOX500 series*CE, FCC, EN 50155 and IEC 60945 compliant
-
Product
Turns Ratio Testers
TRT Advanced Series
-
TRT Advanced series is the newest DV Power solution for transformer turns ratio measurement. Besides its main application, each turns ratio tester from this series also measures transformer excitation current and phase shift. Furthermore, all models perform automatic vector group detection and magnetic balance on three-phase transformers and three-phase autotransformers. They have a built-in true three-phase power source. For that reason, they can test transformers with special configurations, such as phase-shifting, rectifier, arc-furnace, traction transformers, etc.The instruments can output test voltages from 1 V AC to 500 V AC, depending on the model. With the highest test voltage 500 V AC, TRT500 provides the most accurate turns ratio testing of power transformers used in power generation and transmission. The output test voltage of TRT500 can be boosted to 5 kV AC using the external CVT20 extension transformer. This application is specially designed for testing turns ratio of capacitive voltage transformers. The other three models, TRT400, TRT250, and TRT100 can output up to 400 V, 250 V, and 170 V respectively. The low test voltage of 1 V AC enables turns ratio verification of current transformers.TRT500 is equipped with a large 10.1” graphical touch screen display. Other models, (TRT400, TRT250, TRT100) have 7” graphical touch screen display. Besides making the interface much more user-friendly compared to older turns ratio testers, it also brings certain options that were previously available only with DV-Win software. The most important are test templates and automatic test mode. Users can simply create test templates, store them in the instrument’s memory, and load when in the field with just a few clicks.This turns ratio test set, as well as all other DV Power turns ratio testers, has a built-in tap changer control unit. It enables remote control of an on-load tap changer (OLTC) directly from the instrument. In order to make the most out of this feature, the instrument can be programmed to do everything automatically – running turns ratio tests, changing OLTC tap positions, and saving results. This option, especially in combination with test templates, significantly facilitates and shortens the turns ratio testing time. Automatic test mode minimizes human errors, which makes the measurement more reliable.
-
Product
Relay Pro 12-24V Relay Tester
60150
-
Tests relays by simply clipping the test leads onto the relay terminal pins using a 12 or 24v DC power source. Tests a wide range of 4 and 5 pin relays. Including shielded, nonshielded, relays with different pin sizes and 4 pin normally closed relays that other testers may incorrectly show fail. Automatically determines the relay configuration so the fully insulated gator clips can be connected in any order. Eliminates guesswork because you don’t need to connect to specific pins, like other testers. 45" power leads with heavyduty gator clips provide a secure connection to the power source.
-
Product
Triple Output Power Supply
U8030 Series
-
The Keysight U8030 Series variable DC power supply has a total output of 375 W—making this solution an ideal power source in the design and manufacturing of electronic devices. The U8030 Series power supplies feature an output sequencing capability for semiautomated tests. These power supplies enable you to generate output sequences with minimal programming skills. This solution features excellent load regulation and clean output noise for continued stability.
-
Product
Short-circuit and Earth Fault Indicators
-
The Sensorform range of Short-circuit and Earth Fault Indicators detects short-circuit and earth faults on medium voltage underground cables. A wide range of options are available for enclosure type, power source, indicator type, reset method, trip-level selection, auxiliary outputs, and remote indication.
-
Product
1550nm High Power Fiber Optical Splitter
HPFS-1550-口口-1×N
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HPFS-1550 series high power fiber optical splitter and adopt special process of fused bi-conical taper technology and good heat treatment. It can be applied by divided high performance and high reliability to multi-port optical power distribution of 1550nm high power laser light source. The maximum pass power is 50W（47dBm）.The feature of the product is high stability, high uniformity, low polarization dependent loss and low excess loss.
-
Product
Programmable Electronic Load
-
Shenzhen UYIGAO Electronic Technology Co., Ltd
UYIGAO DC electronic loads provide you with the flexibility to test a wide range of power sources. Perform both static and dynamic tests to ensure that your devices can handle the steady state and occasional transient loads. The 16-bit voltage, current, and power-measurement systems provide accuracy analysis.
-
Product
SLED Source Driver
S-108
-
SLED Source & Driver slot module of FOTS system is an efficient module that can drive a stable high power broadband source and modulate a high power SLED to output a high bit rate optical signal. As a high power broadband SLED source, this module can drive the maximum output power of more than 14 dBm and has a stable wideband source characteristics of >90nm@-20dBm/nm. As a high current (400mA) modulation technique, it shows a high power and high bit rate digital signal of > 155 Mbps with > 13 dBm peak power.
-
Product
Miller 400D
44550
-
No need to select ranges or adjust dials – the Miller 400D provides a direct read-out of resistance with the push of a button• Bluetooth interface allows optional data-logging via a Bluetooth-enabled PC (or PDA)**• Rugged, hard plastic case - safe to use on wet ground – IP67 rating for dust and water intrusion• Resistance measurement range from 0.01Ω to 10MΩ (auto-ranging) • High resolution digital display• Resistance measurements are unaffected by any stray interference signals that may be present in the earth during readings, due to the use of narrow band-pass filters centered at 82.2Hz (the unit’s operating frequency)• Runs on a set of replaceable D-cell alkaline batteries...no need to periodically recharge the unit or to plug it into a power source• Performs 10,000 single readings on a fresh set of batteries• Integrates with Universal Rectifiers’ Soil Depth Selector/Multi-Pin Cable Harness System (please see Integration with Universal Rectifiers’ Cable Harness)
-
Product
LCM Tester
Model 27012
-
To meet the high accuracy and low price requirements for LCM TV test device, Chroma 27012 that integrates the signal and power source provide a complete test solution for LCD Module. Its LVDS, TTL (Option) signal source fully complies with the digital signal standard, meanwhile with the 24V, 12V, 5V, 3.3V DC source output it is able to supply power to VDD, Backlight for LCM test without obtaining external power source. Equipped with the interface of single key to switch the Timing, Pattern and Program rapidly for test in auto or manual mode, the 27012 is able to provide a direct and convenient test environment for LCM TV by its complete hardware configuration and easy operation.
-
Product
AC Source
AFC
-
The AFC Series products are single and three phase AC Power sources ranging from 0.5kVA to 2000kVA. This AFC series has a continuous and adjustable output voltage between 5~300V. This allows for quick and convenient 3 scales of preset voltage for high and low voltage simulation. Power is supplied by state-of-the-art IBGT pulse width-modulated power amplifiers resulting in highly efficient power conversion, compact design and maximized performance. With up to 90% efficiency the AFC minimizes heat dissipation so less infrastructure cooling is required.
-
Product
Power Measurement Tool
REAMP
-
Very accurate and stable power source for projects requiring ultra-low power consumption analysis.
-
Product
ENA Vector Network Analyzer
E5080A
Vector Network Analyzer
9 kHz to 4.5/6.5/9 GHz, 2- or 4- port, 50 ohmWide dynamic range 152 dB (typical)Fast measurement speed 3 ms (401 points)Low trace noise 0.0005 dBrms (typical)High temperature stability 0.005 dB/CWide source power range 90 to +15 dBm (spec)Intuitive touch-based GUI on large, high-resolution 12.1" screenE5071C/8753 code compatibility Every spec verified, adjustments included Lock in support & peak performance from the start
-
Product
Pitot-Static Tester
PS-425
-
The PS-425 Pitot-Static tester is a low-maintenance, digital tester that is fully portable. The PS-425 is powered by an internal rechargeable 12 volt battery (included in purchase), which enables the test set to be used completely independent of any external power source. A connector is provided for an external 12 volt DC power adapter (included). The PS-425 incorporates the altitude, VSI, and airspeed in one single display. The PS-425 is designed and priced for non-RVSM markets, and includes two quick-connect hoses, 12 VDC power adapter, calibration certificate, and a limited 2-year warranty. This product is ideal for performing simple go/no-go leak tests, as well as for general use as a low-end pitot-static tester.
-
Product
Portable Electrical Management Systems
EMS-LCHW50
-
Progressive Industries Portable Electrical Management Systems (EMS) provide full RV protection against all adverse power conditions. You will feel secure with multi-mode surge, voltage, polarity and lost/open neutral protection. Each unit includes a digital display, scrolling continuously through the power source information: Voltage(s), current, frequency, error code, and previous error code (if applicable). Replacement parts are simply plug-and-play, making repairs quick and easy. As with our portable models, the computer is driven by state of the art microprocessors. Should the software ever change, EMS owners can receive a free upgrade at no cost.
-
Product
Super MUTT Head Portable, Remote Controlled Diagnostic Trailer Tester
#9005A
-
Innovative Products of America
The Super MUTT Head is a portable, remote controlled diagnostic trailer tester for inspecting lighting, ABS and air brake systems on commercial type trailers. Specially designed for service trucks and offsite inspections, the Super MUTT Head is powered by an (optional) internal 12v battery, or external power source such as a service truck battery, using the supplied external connector and requires shop air for air brake application.
-
Product
Borehole Impulsive Source Of Choice
G-SOURCE
-
Over the years the Sercel G-SOURCE range of products has become the system of choice for advanced VSP surveys, in both offshore and onshore environments. The G-SOURCE and delta cluster combine the advantages of a powerful source and a clean acoustic performance to maximize borehole data quality.
-
Product
MM Fiber Test
KI-TK032
-
850/1300 nm source & power meter, inspection microscope, cleaning materials. Interchangeable SC & LC connectors
-
Product
Coil Analyzers & Power Supplies
-
Coil analyzers and power supply units are portable and lightweight devices intended for use in harsh switchyard and industrial environments. The typical application is switchgear and circuit breaker testing when substation battery is not connected or available. An advantage over substation battery is enabled testing in under-voltage and over-voltage conditions. Furthermore, the stable voltage outputs with a very low ripple (<0,5%) enable an analysis of the coil and motor current graphs recorded with circuit breaker analyzers from different vendors.SAT40AD, POB30AD, and POB40AD are unique devices in the market due to their dual purpose:Power supply for coils and spring-charging motorsTesting circuit breaker’s coils, motor, and auxiliary circuitAll DV Power coil analyzers and power supply units have four separate outputs for opening and closing coils.SAT40AD has two powerful motor outputs (AC and DC) which can withstand up to 40 A inrush current.POB30AD and POB40AD have DC motor output rated up to 30 A and 40 A respectively. With the use of motor outputs, POB and SAT can also be used as a power source or a temporary battery charger.SAT40A II series instruments can be controlled via PC. The DV-Win application software is used to control both SAT and CAT (Circuit Breaker Analyzers & Timers) devices at the same time, making a unique test system for switchgear and circuit breaker testing.
-
Product
Low Distortion 1kW Power Source With UK/Schuko/USA Socket.
AC1000A
-
Provides an EN61000–3–2 compliant source1000W power capability at 230VUp to 4·4A rms load current and up to 10A peak currentsComprehensive overload protectionConnection via standard power connectors
