AXI
1) Advanced eXtensible Interface 2) Automated X-ray Inspection
See Also: Automated X-ray Inspection
-
Product
Field Probe Positioner
-
The Field Probe Positioner FSM2315 is designed for the automation of the 16 point measurement, according to IEC/EN 61000-4-3. The system provides X and Y axis positions for continuous and step by step movement for the filed probe, 0.8m above the floor and with a 1.5m x 1.5m area, for the 16 sensor positions. A dismountable solution is available.
-
Product
Angular Interferometer
10770A
-
The Keysight 10770A Angular Interferometer is a high accuracy plane mirror interferometer ideal for use in precision calibration applications. Used with the 10771A Angular Reflector in an 5530 Laser Calibration System, the interferometer measures pitch and yaw motions along each axis that a machine tool or measuring machine travels. The system can help quickly locate and evaluate unwanted angular motion.
-
Product
Accelerometers & Angle Sensors
-
Accelerometers & Angle SensorsSingle axis, triaxial accelerometers and impulse hammers for vibration measurement and structural modal analysis.Angle sensors are perfect complementary sensors for applications like order tracking.
-
Product
POF Ext Ø 1,5mm 600mm, from 5mm Lens to VPC ITA Contact
YAV90CLR10
LED Sensor
The probes for sensing LEDs, P/N YAV90CR10 feature an Optical Head to correct missalignment errors in X and Y axis. As a result, the relative read out will oscillate less tan 5% with a missaligment of + 0,5 mm Offset
-
Product
Seismometers
3T-120 Pothole
-
120 s to 50 Hz frequency response (option to 100 Hz), 1500 V/ms-1 (2 x 750 V/ms-1) sensitivity, Covers the complete seismic spectrum with a single transfer function, Measured Self noise below the USGS NLNM from 166 s (0.006 Hz), remaining below the high frequency limit of the NLNM at 10 Hz, High linearity: >111 dB (USGS figures), Dynamic range of 167 dB at 1 Hz (Full octave width across 1 Hz), Cross axis rejection over 65 dB; sensor axes orthogonal to within ±0.05°, Remote, automatic electronic mass locking, unlocking and centring, Operating tilt range of ±5° with adjustable feet for off-horizontal installation bases, Low power consumption: 0.75 W from a 10–36 V supply, Stainless steel enclosure, 100 bar / 10 MPa waterproof connector, IP68 - protection against effects of permanent immersion under pressure to 350 m depth
-
Product
CAM/TRAC Test Kits
Series 40
-
The CT Series 40 CAM/TRAC mechanical kits, utilizing the patented CAM mechanism, offer precise Z axis linear motion when testing higher point count and finer pitch test centers. By using the Z axis motion, side load of the test probes is minimized thus increasing probe life and performance.
-
Product
Multi Axis Load Cells
-
Multi-Axis Sensors are designed to measure a multiple of forces and moments simultaneously with a single load cell sensor. These sensors provide multiple bridges that precisely measure the applied force from one direction with little or no cross-talk from the force or moment.
-
Product
SparkFun Triple Axis Accelerometer And Gyro Breakout
MPU-6050
-
The MPU-6050 is a serious little piece of motion processing tech! By combining a MEMS 3-axis gyroscope and a 3-axis accelerometer on the same silicon die together with an onboard Digital Motion Processor™ (DMP™) capable of processing complex 9-axis MotionFusion algorithms, the MPU-6050 does away with the cross-axis alignment problems that can creep up on discrete parts.
-
Product
SparkFun Triple Axis Accelerometer Breakout
LIS3DH
-
The LIS3DH Breakout is a smart, low-power, three-axis, capacitive micro-machined accelerometer with 12 bits of resolution that you can use to add translation detection to your project. It would be classified as a 3DoF, or 3 Degrees of Freedom. Inertial Measurement Units (or IMUs) can provide additional space location data, such as gyroscopic or magnetometric. The LIS3DH provided on this breakout operates under the same principles but gives a few analog inputs to play with, and it has some built-in movement detection abilities.
-
Product
Putting Sensor
GSA Putt
-
3Bays’ 9 axis putting sensor captures even the most subtle movement so you can uncover the science behind your stroke and sink more putts. This game-changing device can help any golfer increase consistent and confidence and cut strokes off your scorecard.
-
Product
Torque Detector for High Rigidity
DSTP Series
-
The DSTP series is designed as the large capacity type torque detector which is able to perform the torque measurement from standstill axis to a high speed rotation. Four types of large capacity products are available.
-
Product
Test Chambers
-
The left-hand axis scales the level of the 100 measurements and the right-hand axis displays the uncertainty to a statistical confidence level of 95%; proving the repeatability is better than +/-0.25dB between the measured values. Guaranteeing repeatability, accuracy and correlation across Lab’s, across Production lines and across the World
-
Product
PXI/PXIe RF Matrix, Dual 2x2, 2.5GHz, 75Ω, SMB
40-837A-002
Matrix Switch Module
The 40-837A-002 (PXI) and 42-837A-002 are 75Ω 2x2 RF matrices with 2 banks in a single slot. Loop-thru connections are provided on both the X and Y axis allowing the attachment of terminations for unused signals or for expansion to other matrices. Larger matrices are easily built with varied X and Y dimensions, such as 8x2 and 4x4 using multiple 40/42-837A modules.
-
Product
QW-AddIn For Autodesk® Inventor® Software
-
QW-AddIn for Autodesk® Inventor® Software is a QuickWave plug-in for Autodesk® Inventor® Software, a wide-spread mechanical tool, allowing defining a complete project for electromagnetic simulation, also periodic structures and axisymmetrical structures (V2D), directly in the popular CAD environment. A set of self-explaining dialogues provides very convenient tool for setting the electromagnetic properties such as assigning the materials, adding ports, boundary conditions, setting postprocessings and excitation parameters.Automatic mesh generation using Automatic Meshing Intelligent Generation Option (AMIGO) optimises the meshing taking into account requested wavelength resolution in all media, while avoiding unnecessarily small cells. Additionally QW-AddIn for Autodesk® Inventor® Software can be used for optimisation and parameters sweep with QW-OptimiserPlus.QW-BHM is available and heating parameters can be defined together with rotation in XY plane along axis parallel to Z axis. Creating proper axis of rotation can be done by selecting edge or solid body from the project. It will contain the middle point of selected object and its location can be modified either with the mouse or by entering new coordinates.
-
Product
3 Axis Digital Fluxgate Vector Magnetometer
WFG-D-120A
-
The Model WFG-D-120 magnetometer is a tri-axial vector magnetometer system with a high-speed digital interface that can transmit XYZ magnetic field values at up to 140 times per second.
-
Product
MEMS-Scanner Evaluation-Kit
-
The "QSDrive Scan Kit" evaluation kit enables small and medium-sized companies in particular to operate ResoLin components from the Fraunhofer IPMS in accordance with the specifications without the time-consuming in-house development of control electronics. The evaluation kit consists of a ResoLin component – a cardanic MEMS scanner with a linear axis and an optional, orthogonally oriented resonant axis – and control electronics that enable the components to be operated with an optimized trajectory supplied. The component is held by a scan head, which is also included in the scope of delivery and which, thanks to its special construction, can easily be integrated into common optical test setups. Depending on the design of the MEMS component, controlled operation of the component and synchronized operation of the resonant axis are also possible. The function is controlled by software that communicates with the electronics via USB.
-
Product
50 KN Capstan Grips For Rope
-
These 50 kN (11,000 lbf) capstan grips are designed specifically for testing the tensile properties of rope with a diameter between 8 and 28 mm (0.31 and 1.1 in). The upper and lower grips incorporate an easy-to-load split drum and the upper grip has a counterweight attached to maintain alignment of the grips with the axis of the universal tester during testing.
-
Product
Linear Accelerometers
-
Columbia Research Laboratories
Columbia Research Labs line of Force Balance Linear Accelerometers offers low cost, high performance, general purpose single axis accelerometers that are ideal for DC and low frequency measurements, with both voltage and current signal outputs available. Also offered are Columbia's Solid State Sensors and our specialized Airborne Sensors that generate outputs specifically designed to operate from +24 to +32VDC aircraft power, that is excellent for airborne telemetry applications. And our Low Noise Sensors are designed for use in seismic, low level, low frequency motion studies.
-
Product
Biaxial Linear Accelerometers
-
Columbia Research Laboratories
The line of Biaxial Force Balance Linear Accelerometers available are 2-axis versions of our General Purpose, Low Noise and High Temperature, and High Performance Single axis Linear Accelerometers.
-
Product
Hardware Platform
SmartScan 3D
-
SmartScan-3D is another hardware platform that allows 3D scan using a six axis robot and DUT holder. A DUT is placed on a 360 degree rotating DUT holding jig. Vertical scanning without rotating DUT holder is one variation of SmartScan-3D for any DUT that is standing up, rather than laying flat on X-Y plane. Any scan technology can be integrated to the SmartScan-3D.
-
Product
Hand-held Textile Moisture Meter
TF123B
-
TESTEX Testing Equipment Systems Ltd.
Hand-held Textile Moisture Meter, widely used in leather materials, fabrics, garments, yarn, axis, cheese, textiles and other industries that need rapid determination of moisture (moisture regain).
-
Product
Single Axis Magnetometers
MAG Serie
-
Macintyre Electronic Design Associa
The µMAG series is the premiere, handheld instrument for the precision measurement of the vector components of weak static and low frequency magnetic fields. The superior stability, linearity and accuracy of the uMAG, compared to Hall Effect or Magnetoresistance base instruments, make it the only choice for high quality low magnetic field measurements and best choice for gerneral purpose magnetometer applications.
-
Product
High-Resolution VMEbus Laser Axis Board
10897D
Laser Board
The 10897D High-resolution VMEbus laser axis board provides excellent resolution of up to 0.3 nm with a high resolution interferometer. The data age uncertainty is dramatically reduced allowing extremely accurate measurement and control of moving systems. The very high data rates accommodate high-bandwidth and high-performance closed-loop applications. Configured with appropriate lasers and optics components, the 10897D supplies unsurpassed positioning accuracy for dynamic measurement.
-
Product
Super Quality Fiber
-
Panasonic Industrial Devices Sales Company of America
These Super Quality Fibers are designed with an extremely small beam axis curvature and gap which results in a high stability of light intensity. When combined with the FX-500 Amplifiers, the stability of light intensity is improved up to 4 times compared to traditional Fibers.
-
Product
CAMGATE Test Kits
Series 453
-
LThe GR Series 453 CAMGATE mechanical kits, utilizing the patented CAM mechanism, offer precise Z axis linear motion when testing higher point count and finer pitch test centers. By using the Z axis motion, side load of the test probes is minimized thus increasing probe life and performance. The Series 453 provides interface compatibility using the GR2270 Style, 12 block interface. This interface accepts the industry standard I/O, power, and coax blocks. The CAM/GATE utilizes a cam roller system for precision guiding and smooth operation and 1.00” push plate movement. The gate assembly is movable to three different positions which allows for the versatility of top side probing, or relocating the frame assembly for PCA’s the have tall components.
-
Product
Universal Test Fixture
Series 48
-
The Series 48 Universal Test Fixture Systems are an effective way to test high mix, low to medium volume products. The Universal Base is designed around the CAMGATE Z axis Test Fixture. The base interfaces with removable, quick change Series 49 Universal Test Insert Kits. Three versions are offered, a blank base whereas the end user can configure the Base and insert kit to their own connector configuration, The 160 point model which uses four (40) pin IDC ribbon cable connectors to interface between the base and the insert kit, and the -I model that incorporates the same 4 block GR2270 style block interface as used on our Series 34 test fixtures. This allows for increased test point count and the use of Industry Standard 2270 style signal, power, and coax blocks. Rear panels can be custom configured to customer specifications, Virginia Panel ITA frames, or GR2270 Interfaces used on Semco’s Standard Product line
-
Product
Gyroscopes
-
A device consisting of a wheel or disk mounted so that it can spin rapidly about an axis that is itself free to alter in direction. The orientation of the axis is not affected by tilting of the mounting; so gyroscopes can be used to provide stability or maintain a reference direction in navigation systems, automatic pilots, and stabilizers.
-
Product
CNC Rotary Axis Calibrator
API Swivelcheck
-
API SwivelCheck is light-weight & comes with a convenient carrying case to easily transport & install on a variety of CNC machines.
-
Product
Digital Gaussmeter
DGM-1D
-
DGM-1D: Digital Gaussmeter capable of measuring DC and AC magnetic field strength along one axis.
-
Product
Miniature Fluxgate Magnetometer
WFG-130
-
The Model WFG-130 magnetometer is a complete 3 Axis Fluxgate Magnetometer system packaged in a rectangular package of dimensions 1.5\" x 1.5\" x 2.775\".
