Melt Flow
See Also: Flow
-
Product
AC Fuel Flow Signal Generator
TA-100
-
The TA-100 signal generator was designed to facilitate testing of aircraft fuel flow indicators that require two input signals designated as “Drum” and “Impeller”. This generator provides both signals so as to provide a direct interface to the fuel flow indicator under test. The generator also provides switched power out to the unit under test as well as a 5v source for testing the bezel lighting. The original design was built around the requirements for the AMETEK series indicators (pn: 10171 series). This generator simulates a reference and a time delayed signal of appropriate amplitude for an indication of up to 1200pph for the indicator under test. The “PPH Select” switch provides fixed signal delays representing 0, 200, 400, 800, 1000 and 1200pph flow rates respectively, this provides the mechanic with an expedient check of the indicators accuracy. The “PPH Adjust” control allows the mechanic to vary the signal delay throughout the full range and serves as a good method for checking of pointer smoothness from stop to stop. The unit’s front panel also provides test jacks to monitor the “FDR Output” as well as the drum and impeller signals. The TA-100 requires only 28Vdc to operate. This generator provides a very economical approach to any repair facility or flight department as it becomes an alternative to purchasing two bench top signal generators. The TA-100 generator at the very least can provide a simple functional test and eliminate the high cost of exchanging an indicator as a function of troubleshooting the aircraft system.
-
Product
High Temperature Digital Mass Flow Controller
SEC-8000 F/D/E Series
-
The SEC-8000F/D/E series can operate in high temperature environments, from 15 ℃ to 120 ℃, for a variety of tasks including semiconductor and compound semiconductor processing.
-
Product
Handheld Ultrasonic Flow Meter for Liquid
P117
-
Gentos Measurement & Control Co.
P117 is a hand-held flow meter equipped with external clip-on transducers, which can meet the needs of convenient and fast flow measurement, allowing you to quickly transfer and measure data between different working environments and improve work efficiency.
-
Product
Electromagnetic Flow Meters
-
Electromagnetic (mag) flow meters are volumetric flow meters that do not have any moving parts to wear down, reducing the need for maintenance or replacement.
-
Product
High Speed & Precision Pressure Insensitive Mass Flow Module
D700MG
-
Critical semiconductor manufacturing processes continuously desire precision gas flow control devices that enable both future innovation, and lab to fab transition of leading edge memory and logic device. HORIBA's propose the new pressure based MFC D700MG, the upper compatible model of the D500MG to support customer’s challenges.
-
Product
Thermal Flow Splitter
FS-3000
-
FS-3000 combines HORIBA STEC’s mass flow controller (MFC) and MuCube (Master controller). By controlling MFC from MuCube equipped with the HORIBA STEC’s proprietary control algorithm, FS-3000 achieves stable splitting control.
-
Product
Variable Constant Differential Flow Controller
VCD 1000
-
The Porter Model VCD 1000 flow controller is precision-engineered to control low gas flows at constant mass flow rates regardless of changes in downstream pressure.
-
Product
Acoustic Scintillation Flow Meter
ASFM
-
Assess/optimize existing turbine operating efficiencyAccept new or upgraded turbinesVerify minimum flow requirements
-
Product
500 HP Complete Bench Hydraulic Test Center With High Flow Supply
HTC-500-HFS
-
The Hydraulic Test Center (HTC) is a versatile machine designed to test heavy-duty, off-highway hydraulic components. The 500 hp (373 kW) HTC Complete Bench is for the dealer that services components from a predominately larger machine size mix such as large mining machines and large excavators. The Complete Bench offers full functionality to test all types of pumps and motors including: transmissions, hydraulic motors, hydraulic cylinders, valve blocks, torque converters, open and closed loop pumps.
-
Product
Stopped-flow/quench Flow
µSFM.
-
A unique micro-volume stopped-flow solution for the most demanding applications
-
Product
Vapor Mass Flow Controllers
-
Heated pressure-based mass flow controllers are designed to meter and control vapor from low vapor pressure liquid and solid sources directly, without the need of a carrier gas.
-
Product
High Flow Mass Flow Controllers
-
High flow thermal mass flow controllers and meters offer both elastomer and metal seals for flow rates up to 300 slm. Versions are available for standard and harsh environments where protection from water and dust is required.
-
Product
Micro Flow Sensor
2000
-
The Signet 2000 Micro Flow Sensor is constructed from Polyphenylene Sulfide (PPS), which provides high material strength. The 2000 MicroFlow Sensor offers two flow ranges starting at 0.11 or 1.13 lpm (0.03 or 0.3 gpm), for clean process liquids, regardless of fluid color or opacity.
-
Product
Liquid Flow Meters & Switches
-
Measure liquid flow rates quickly and more accurately with Sierra transit-time ultrasonic flow meters, vortex flow meters or thermal flow switches. Manufactured by Sierra’s team of flow engineers, our liquid flow meters are suited for even the most challenging liquid flow applications.
-
Product
BS Viscosity Flow Cups
2354
-
The Elcometer 2354 BS Viscosity Flow Cups are very easy to use instruments made of anodized aluminium with a stainless steel orifice, for measuring the consistency of paints, varnishes and similar products.
-
Product
Dual Pitot Tube Flow Meter
PTFM-ONE-DT
-
The Dual Pitot Tube Flow Meter, PTFM-ONE DT is a standalone interface for measuring exhaust gas flow rate of combustion engines. The system uses the tried-and-tested pitot tube principle with high-frequency transducers, with a sampling rate of 1kHz to accurately measure highly pulsating exhaust flows. This rapid capture rate ensures that any pulsations or exotic behaviour caused by the engine is measured, and the unique design of the PTFM-ONE DT means reverse flows can be calculated, with the same guarantee of sensitivity.
-
Product
Pneumatic Module, ITA, 5 Position (3/8" Flow)
510108144
ITA Module
The 5 Position Pneumatic Modules are made of G10 Epoxy Glass, withstanding temperatures of 140°C. Nomenclature is silk-screened white onto the Modules.
-
Product
Flow Meters
-
Measure the flow of solid bulk products with precision and speed. Flow meters offer a compact and efficient design for use in a variety of spaces and applications, including explosive and hazardous environments.
-
Product
Daniel Flow Gauge
2290
-
The Elcometer 2290 Daniel Flow Gauge is a simple gauge used to conduct flow measurement of thick or paste-like materials, such as paints or printing inks.
-
Product
Insertion Flow Meter
SPI Mag
-
The SPI Mag Insertion Flow Meter provides a highly cost-effective solution for the accurate measurement of liquid flow in closed conduit, pressurized pipe applications. Unlike conventional magnetic meters, the SPI Mag's cost is independent of pipe size.
-
Product
Ultra Clean, High Concentration, High Flow Ozone Generator
SEMOZON® AX8415
-
The SEMOZON® AX8415 is the most innovative and versatile ozone generator developed by MKS. Ultra clean, high concentration, high flow ozone is produced by this generator's novel architecture and patented cell design, converting oxygen to >400 g/Nm3 of high concentration ozone for leading-edge applications in the semiconductor, flat panel display and photovoltaic industries.
-
Product
Flow Switches
-
Not susceptible to contamination and can be oriented in any pipe configuration make these flow switches for liquid or air maintenance free and reliable. Mechanical and electronic designs available
-
Product
Liquid Flow Controllers
LC-series
-
Alicat Scientific, Incorporated
The LC-series liquid flow controller uses Alicat’s patented laminar flow design to provide users with fast, accurate, and stable volumetric flow control for water or selected other liquids (see Quick Specs below). At the heart of Alicat’s LC-Series liquid flow controllers is an internally compensated, laminar differential pressure measurement technology that yields linear results over a wide flow range.
-
Product
Probes & Flow Cells
-
The sample interface is a virtual “windows into the process” and is a critical component of any optical analyzer system. Guided Wave sample interfaces (probes, flow cells) are designed for use with NIR or UV/Vis fiber optic coupled analyzers. They are designed to be rugged and reliable in harsh chemical and physical process conditions while providing optimal transmission for long-term reliable measurements.
-
Product
Flow Logger Sensor
NUL-224
-
This sensor allows for a stream of water to flow through its inlet and outlet pipes, thus revolving a rotation wheel within it. The wheel is not connected mechanically to anything else, but rather floats on a bearing for minimum friction and the enhancement of its minute accuracy. The measuring is done by monitoring changes in the sensor's surrounding magnetic field.
-
Product
Stopped-flow/quench Flow
QFM-4000.
-
A unique design enables the QFM-4000 to trap and identify reaction intermediates. The device is also commonly used for analysing enzymatic reactionq, DNA cleavage or single turnover reactions.
-
Product
Flow Meter
SK-FM
-
Beijing SANKI Petroleum Technology Co., Ltd.
High-precision metering device FM-500 was independently developed and manufactured by SANKI Company based on advanced technologies from Europe and America as per international metering standards OIMLR117 and OIMLR118
-
Product
Coriolis Mass Flow Meters And Controllers
-
Alicat Scientific, Incorporated
Use low-flow CODA Coriolis mass flow meters and controllers for measurement and control of true mass flow at an accuracy to ±0.6% of reading at prices starting at $2,100.
-
Product
LPG Mass Flow Rate Detection System
-
This is a massflow rate measurement system that can measure the massflow rate of LPG with high accuracy using the Coriolis method massflow meter.LPG is a fuel that easily vaporizes, and it is not difficult to measure the correct flow rate in a gas-liquid mixed state.
-
Product
Special Application Thermal & Pressure Mass Flow Controllers
-
Certain process vapors and gases require mass flow controllers of a special design specific to the material as well as process conditions. MKS offers both thermal mass flow controllers and pressure based mass flow controllers for these applications that require flow control at elevated temperatures and/or low pressure drop conditions given the source material characteristics.
