PCB Adapters
-
Product
Chip Test Adapter
SOJ EDO/FPM
-
Our new addition to the RAMCHECK line provides support for common 20 to 42-pin EDO/FPM DRAM SOJ chips of sizes 256Kx16/18, 1Mx16/18, 8Mx8, 16Mx4, 2Mx8, 4Mx4, 16Mx1, 1Mx4, and 4Mx1.
-
Product
Adaptive Infrared Imaging Spectroradiometer
AIRIS
-
The Adaptive Infrared Imaging Spectroradiometer (AIRIS) has been developed for real-time standoff detection of chemical vapors and biological aerosols as well liquids and solids (such as chemical agents and trace explosive residues) on surfaces.
-
Product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type Q, Ø0.80mm, 155gf
K100-Q080155-SKAU
Spring Probe
K100 Series, Pitch 100mil, Tip Style Q, Tip Diameter Ø0.80mm, Spring force 155gf, Steel with Gold Plating.
-
Product
Adapter Kit, 3.5 mm to Type-N, DC to 18 GHz
11878A
-
The Keysight 11878A adapter kit provides the RF components generally required when an SMA or 3.5 mm device needs to be measured with a network analyzer type-N configuration. This kit includes four type-N to 3.5 mm adapters for both male and female connectors.
-
Product
96-Pin SCSI Micro-D Straight PCB
40-963-096-SF
SCSI Female PCB Mount
Ideal for user created termination schemes where the termination is to be on the front of the product or remotely connected to the module by cable. Suitable cables for this product are detailed in the data sheet. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires.
-
Product
DDR4 Pro 288-Pin DIMM Adapter
INN-8686-18-PRO
-
Your best option if you need to test a large volume of memory! The RAMCHECK LX DDR4 Pro 288-pin DIMM Adapter (p/n INN-8686-18-PRO) gives RAMCHECK LX users the power to test 288-pin DDR4 modules, including unbuffered (UDIMM), load-reduced (LR-DIMM) and registered modules (RDIMM), both ECC and non-ECC, that comply with JEDEC standards. It includes the DDR4 Series adapter and DDR4 Pro DIMM test head.
-
Product
Signal, Contact, Receiver, QuadraPaddle, 5 Amp, Male Adapter, .025" Round Post (Adapter Pin)
610138117
Signal Contact (Receiver)
Primary mating contact 610138100. (May mate with other Twin Female contacts, as well.)Specifications Operating Voltage & Current 5 Amps Max. Continuous; 600 volt Max. use of wire Mil-W-16878/4Contact Resistance 25 mOhms Max.Measured at 50 mV @ 100 mADielectric WithstandingVoltage (DWV) 1500 VDC Min.Insulation Resistance 5000 MOhms Min.Contact Body BrassContact Plating 30µ” Au over 100µ” NiCycle Life 20,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAVG Mating Force (lbs) 0.24
-
Product
Test Adapter
cPCI/VME/VME64x
-
The test adapter is used for measurement and testing of test specimen boards, which gives optimal access of signals, address lines as well as power from backplane assembly. Usually the test adapter includes fields for voltage and amp, current measurements and in some cases also some pins for wire wrap to conduct custom connections.
-
Product
Passive XMC-to-PCI Express Adapter
5944
-
The Technobox, Inc. P/N 5944 is designed to adapt a single-wide XMC card to a 16X PCI Express slot. The 5944 supports both P15 and P16 and allows access to PN4 signal via the adapter's DIN connector. The A and C rows of a 96-pin DIN connector connect with the 64-pin user I/O connector (J4/P4) on the mezzanine card, permitting internal connection of rear I/O.
-
Product
Engine Test Adapters
-
Atec has built test adapters for a wide variety of engines from high bypass fan engines to small APU engines. Testing a new engine type in your existing jet engine test cell can be challenging, and upgrade modifications will be needed. Atec does not view an adapter as just a mechanical weldment that simply mates the engine to the aeroengine thrust stand. Our engineers realize that additional items will be needed in the facility to insure total project success. During the planning phase, Atec engineers can visit your existing facility and/or review videos to make a comprehensive assessment of the integration needed to add a new engine type to your testing facility. Atec can perform airflow, acoustics, FEA and sub systems analyses to ensure that any new engine added to your jet engine test cell will have the proper capacity to perform properly. Vital Link’s current experience with advanced fighter engines test adapter kits further bolsters our expertise in high thrust engine test handling.
-
Product
Module, Receiver, RTCASS, Signal, 210 Position Right Angle PCB Mount for J4
510113140
Receiver Module
Module, Receiver, RTCASS, Signal, 210 Position Right Angle PCB Mount for J4.
-
Product
Signal Module, ITA, QuadraPaddle, 192 Position, Right Angle Contacts For Custom PCB Mounting (510 151 107 And 510 109 316)
510151121
ITA Module
This kit has everything you need to attach a VPC ITA Module to a custom designed PCB. This includes the right angle header (P/N 510 109 316) and the ITA Module (P/N 510 151 107).
-
Product
Signal Module, Receiver, QuadraPaddle, 192 Position, Right Angle Contacts For Custom PCB Mounting (510 150 130 And 510 109 315)
510150152
Receiver Module
This kit has everything you need to attach a VPC Receiver Module to a custom designed PCB. This includes the right angle header (P/N 510 109 315) and the Receiver Module (P/N 510 150 130).
-
Product
Wearable Wireless Adaptive Refractor
VisionFit SC
-
The VisionFit SC is an innovative, electronic, mobile and wearable adaptive refractor.It performs a subjective sight examination and effectively replaces both the trial frame and the manual/electronic phoropter functionalities. VisionFit SC enables examining in free posture. Subjective refraction can be performed with the patient in his/her usual working environment and posture.VisionFit SC does not require the control of the patient’s position making it ideal for non-cooperative patients. Thanks to its comfortable and small footprint, this device reduces the examination time and increases the peripheral vision.
-
Product
PMC to PCI Express Adapter w/ TSI384
8636
-
The Technobox, Inc 6083 4-lane and 8638 1-lane carrier card allows use of a PMC in a PCI Express edge card slot. The product features an IDT TSI384 bridge IC used in transparent mode with a PCI Express primary side and a PCI/PCI-X secondary side.
-
Product
Test Port Adapter Set, 2.4 Mm To 2.4 Mm
85130G
-
The Keysight 85130G test port adapter protects the test set port from connecting directly with the device under test. It has a special rugged female connector that connects to the network analyzer test port. This special connector does not mate with a standard male connector but converts the rugged test set port to a connection that will mate with the device under test. This set contains a NMD-2.4 mm (f) to NMD-2.4 mm (m) adapter and a NMD-2.4 mm (f) to PSC-2.4 mm (f) adapter. The frequency range for these adapters is dc to 50 GHz with a return loss of 23 dB or better.
-
-
Product
COM Express Type 7 10GBASE-T Network Adapter Card
CEI-2x10GBASE-T
Network Interface Controller
- Support up to two 10GbE BASE-T interfaces- Marvell AQR113C inside- COM.0 R3.1 Type 7 compliant- Dedicated for Express-VR7
-
Product
Coaxial Waveguide Adapter, 1.0 mm (m), 75 to 110 GHz
W281D
-
The Keysight W281D is a 1-mm male to W-band waveguide adapter with a frequency range of 75 GHz to 110 GHz. The Keysight W281D is used with the Keysight 8510XF systems.
-
Product
12C Adapter Slave
I2C RS232 adapter
-
RS model:*RS232 controlledASCII commands via the serial interfaceI2C bus transparent, 1: 1 transmission IC model:*I2C controlledcommands via the I2C busSerial interface is transparent. 1: 1 transfer
-
Product
Test Adapters / Aeroflex Test System
52xx / 5300
-
We develop and manufacture test adapters for your existing interface including documentation and test program
-
Product
PCB Connectors
HPH Series
-
Smiths Interconnect's HPH series is a high density interconnect available up to 303 contacts with multiple hardware choices and backpotting option
-
Product
Signal, Module, Receiver, CASS, 210 Position, J4, Right Angle PCB Mount
510113133
Receiver Module
Signal, Module, Receiver, CASS, 210 Position, J4, Right Angle PCB Mount.
-
Product
NI-5752, 50 MS/s, 12-Bit, 32-Channel Digitizer Adapter Module for FlexRIO
781357-01
Digitizer
The NI‑5752 is a digitizer adapter module that, when combined with a PXI FPGA Module for FlexRIO, creates a high-speed digitizer that simultaneously samples 32 channels at 50 MS/s. You can use the NI‑5752 to do real-time processing and streaming of analog data with high-performance A/D converters. The Digitizer Adapter Module for FlexRIO is ideal for applications that require in-line data processing, high data streaming rates, and deployed high-performance solutions.
-
Product
Current Loop Adapter
OP-1C
-
This adapter supports current loop communications.The kit incorporates a communications circuit with photo-coupler isolation and constant-current power supply of insulated type, thus realizing not only monitoring but also easy communications testing with passive or active current loop devices.
-
-
Product
9-Pin D-Type, Female, Straight PCB Mount
40-963-009-SF
D-Sub PCB-Mount Connector
Accessory allows a user to create their own PCB based termination solution mounted directly on the front of the product or on the end of a cable. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires.
-
Product
Miniature Amplifier PCB
-
Sized for single channel TO-5 packages and electrically compatible with all Dexter Research Center detectors. Available in three amplifier gains: 300, 500 and 1,000 providing convenient buffering and pre-amplification of thermopile signal. Facilitates fast R&D startup time that can be integrated into your prototypes or final system design.
-
Product
Signal Generator Adapter Module For FlexRIO
Signal Generator
Signal Generator Adapter Modules for FlexRIO feature either high or low‐speed analog output and can be paired with a PXI FPGA Module for FlexRIO or the Controller for FlexRIO for custom signal generation. Whether you need to dynamically generate waveforms on the FPGA or stream them across the PXI backplane, these adapter modules are well suited for applications in communications, hardware‐in‐the‐loop (HIL) test, and scientific instrumentation.
-
