PCB Adapters
-
Product
50-Pin D-Conn Male Straight PCB
40-963-050-SM
D-Sub PCB-Mount Connector
Ideal for user created termination schemes where the termination is to be on the front or remotely connected to the module by cable. Suitable cables for this product are detailed in the data sheet. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires.
-
Product
TAP Adapter for Corelis JTAG Controllers
Low Voltage Adapter
Controller
High technology, energy efficient, and small form factor products push JTAG interfaces to the limits; low power and high performance means low voltage, high speed, and high drive requirements. Building specialized interface circuits on product Printed Circuit Boards (PCBs) is inconvenient and costly—an out-of-the-box, external solution is needed.The Corelis Low Voltage adapter is an add-on accessory that provides existing scan controllers with an active, plug-in interface to access low voltage scan chains, without sacrificing performance.
-
Product
Reverse GPIB Cable Adapter
182768-01
GPIB Cable
24-Pin, Female GPIB (IEEE 488) to 24-Pin, Male or Female GPIB (IEEE 488) Adapter - The GPIB Adapter connects GPIB cables to other accessories. NI offers it in Type XA, XE, and XF.
-
Product
Micro Coax, Two Piece Contact, Receiver, PCB Vertical Mount, Solder
610140109
Coax Contact (Receiver)
For vertical PCB terminations. Used with standard 50 and 120 Pin Micro Coax Modules.Up to 10GHz transmission speeds (PCB design dependent). Two-piece contact that allows for pin replacement, field repairable. Mates to all existing Micro Coax contacts.
-
Product
High Force Type Prbobe For PCB, K100 Series 100 Mil Pitch, Receptacle With Wire Wrap Pin
KR100-WP
Spring Probe
K100 Series, Pitch 100mil, Receptacle, with wire wrap pin. Brass with gold finish.
-
Product
44-Pin D-Type Connector, Female, Right Angled PCB Mount
40-963-044-RF
D-Sub PCB-Mount Connector
Accessory allows a user to create their own PCB based termination solution mounted directly on the front of the product or on the end of a cable. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires.
-
Product
PCB IMIB01, 100 mV/g, IEPE, 15 kHz, 2-Pin, Accelerometer, Industrial Vibration Sensor
784176-01
-
The PCB IMIB01 is an industrial Vibration Sensor designed for permanent installations. This sensor helps you acquire sound and movement data with supported PXI Sound and Vibration Modules, C Series Sound
-
Product
PCI-104 Adapter for PMC
PC104p2PMC
-
PC104p2PMC ( PCI-104 to PMC ) adapter / carrier converter card provides the ability to install a PMC card into a standard PCI-104 slot. Suitable for PCI operation with 32 bit data and 33 or 66 MHz bus operation.
-
Product
44-Pin D-Type Connector, Male, Right Angled PCB Mount
40-963-044-RM
D-Sub PCB-Mount Connector
Accessory allows a user to create their own PCB based termination solution mounted directly on the front of the product or on the end of a cable. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires.
-
Product
Digitizer Adapter Module For FlexRIO
Digitizer
Digitizer Adapter Modules for FlexRIO can be used with a PXI FPGA Module for FlexRIO or the Controller for FlexRIO to create a high‐performance instrument with customizable firmware. With sampling rates from 40 MS/s to 3 GS/s and up to 32 channels, these modules cover a wide range of requirements for both time- and frequency‐domain applications. Digitizer adapter modules also provide digital I/O capability for interfacing with external hardware.
-
Product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type H, Ø0.80mm, 230gf
K100-H080230-SKAU
Spring Probe
K100 Series, Pitch 100mil, Tip Style H, Tip Diameter Ø0.80mm, Spring force 230gf, Steel with Gold Plating.
-
Product
Flexible MiniPCI to MiniPCI Express Adapter
SKU-054-0X
-
The Flexible MiniPCI to MiniPCI Express Bus Adapter (Adapter) was designed to convert a standard MiniPCI bus into a MiniPCI Express bus. It allows you to connect a MiniPCI Express board (half-size or full-size) to a motherboard that has a standard 124-pin MiniPCI connector.The Adapter includes a MiniPCI Express adapter board (downstream), MiniPCI host board and PCI Express flat cable.
-
Product
HF test adapter
-
High-frequency test adapters (HF adapters) from INGUN are designed as a replacement set system, consisting of a manual test adapter (MA 21xx and 32xx series) and a high-frequency shielded replacement set from the ATS MAxx/HF series.
-
Product
USB to I2C Adapter
Model JI-300
-
The JI-300 is a versatile, easy to use PC hosted adapter used to drive I2C communicationsto/from a target device. The desktop unit can be configured to interface a variety of I2Cnetworks. Bus parameters such as clock frequency, duty-cycle, setup and hold times, busvoltage, and pull-up resistor values can be varied. JI-300''s diagnostic features including"excessive clock-stretch", "bus-not-free", and "bus contention" monitoring, as well as statusreporting at the conclusion of each message transaction simplifies I2C trouble-shooting. AWindows software application manages the setup and control of the instrument.Communications and unit power is provided via a USB 2.0 connection.
-
Product
4U Grille Adapter
AD-7
-
Used to install 19” panel width blowers, fan and grille/filter assemblies in 24” panel width enclosures.
-
Product
RF Adapters
RP-SMA Adapters
-
Are semi-precision units that provide excellent electrical performance from DC to 34 GHz and outstanding mechanical durability.
-
Product
PCB IMIC01, 100 mV/g, 2-Pin, Accelerometer, Industrial Vibration Sensor
780985-01
-
The PCB IMIC01 is an industrial Vibration Sensor designed for permanent installations. This sensor helps you acquire sound and movement data with supported PXI Sound and Vibration Modules, C Series Sound and Vibration Input Modules, and USB-based Sound and Vibration Devices. The PCB IMIC01 features a sensitivity range of 100 mV/g and uses the Integrated Electronics Piezo-Electric (IEPE) current excitation. The sensor supports the IMI Industrial Accelerometer Cable as well as the MIL2M-Breakout Cable.
-
Product
PCB Test System
Circuit Wizard - CW409
Test System
Qmax Test Technologies Pvt. Ltd.
CW 409 –Circuit Wizard PCB Test System has all the features of QT9627 such as Desktop PCB Test System. It can be configured to maximum 64 Channels of In-circuit Functional Test Channels and 64 Channels of QSM V-I Signature Test.Maximum Digital Test Speed 10MHz in the QT9627 .It can be connected to any PC/AT or Laptop with Windows 10 operating system through USB Plug and play interface. It operates on user friendly Qmax Test Director software platform with different modes like Test Station for operator level use Test Sequencer mode for Programmer level use and Interactive Workstation mode for quick working.
-
Product
Off-Card Adapter,
3910-FOFE
-
As the physical size of Fibre Optic Front End (FOFE) transceivers prohibits their use on PCI, CompactPCI, PMC and ISA (PC/AT) cards, Western Avionics provides an off-card Adapter, that contains all components to support the 3910 Optical implementation of STANAG 3910. The 3910-FOFE Adapter provides a complete dual redundant optical interface, together with dual redundant 3838 connections, and Trigger-in and Trigger-out in a minimal sized package, to allow convenient cabling connections to the 3910 / 3838 system or unit-under-test.
-
Product
Module, Receiver, RTCASS, Coaxial, 64 Position, Discrete Wiring or Side PCB Mount
510113142
Receiver Module
Module, Receiver, RTCASS, Coaxial, 64 Position, Discrete Wiring or Side PCB Mount.
-
-
Product
RF Adapters
MHV Adapters
-
MHV Jack to MHV Jack Adapter Non-Constant Impedance Straight 4-Hole Flange.
-
Product
Adapter, 1.0 Mm (m) To 1.0 Mm (m), DC To 120 GHz
Y1910A
-
Provides measurement accuracy, versatility, and ease of use for on-wafer and coaxial measurements.
-
Product
In-Line Coaxial-to-Waveguide Adapter, 1.0 Mm (m) To WR-12, 60 To 90 GHz
E281DS
-
E281DS In-line 1.0 mm (m) - to- WR-12 waveguide adapter offers a simple way of measuring waveguide devices in E-band, 60 GHz to 90 GHz.
-
Product
Adapter, 2.4 mm (m) to 3.5 mm (f), DC to 26.5 GHz
11901C
-
The Keysight 11901C is a metrology grade, 2.4 mm male to 3.5 mm female adapter with dc to 26.5 GHz operation.
-
Product
Fiber Adapter
I2C fiber adapter
-
*Optical data transmission*Glass fiber or POF*Optimal galvanic isolation*Up to 350kHz*Up to 50m*No software or drivers required
-
Product
RS232 I2C Adapter
12C Master
-
*I2C frequency adjustable up to 400kHz*I2C level shifter, I2C level from 2V to 15V*Interrupt input for external events*Simple software interface (ASCII commands)
-
Product
PCI to PMC Adapter / Carrier
PCIBPMCx2
-
Embedded applications frequently require real time processing coupled with special purpose IO. With the PCIBPMCx2´s two slots; a PrPMC can be matched with another PMC to make a high bandwidth processing node. The PrPMC can communicate with the host for set-up, and then use the local bus to control and transfer data with the special purpose IO card.
-
Product
Chip Test Adapter
RAMCHECK Sync
-
The RAMCHECK Sync Chip Adapter tests popular TSOP SDRAM memory chips in sizes of 16Mx16, 4Mx16, 32Mx8, 8Mx8, 64Mx4, 16Mx4 and more. Picture above shows the adapter with all optional sockets for 54, 50 and 44-pin.
-
