-
product
Neodymium Low Frequency Transducers
High energy neodymium magnetic designs, complex cooling systems and new technologies for high-power handling, minimal distortion and low weight.
-
product
Ultra-Low Frequency Workstation
MK52 Series
Providing Ultra-Low Frequency levels, the MK52 Series offers the ultimate low natural frequency performance for a wide range of high resolution instruments, such as analytical balances, cell injection, confocal microscopes, patch clamping, optical microscopes, wafer probing, sensor calibration, atomic force microscopes and other sensitive equipment requiring high isolation efficiency.
-
product
Series Low Frequency Vibration Sensors
AC136
Low Frequency Accelerometer, Side Exit Connector / Cable, 500 mV/g
-
product
Low Frequency 4-Way Power Dividers To 2200 MHz
Low Frequency 4-Way Power Dividers to 2200 MHz
-
product
Low Frequency Generator
LFG-200
LFG-200 is a cable test van-mountable signal generator used as part of a cable tracing and fault location set for the following applications.
-
product
Advanced Low-Frequency Noise Analyzer
E4727B
Get a deeper, closer look at low frequency noise with the A-LFNA integrated with WaferPro Express, featuring data analysis, wafer prober control and test suite automation.
-
product
Low Phase Noise Frequency Synthesizer
Corech’s low phase noise frequency synthesizer series generates precise and stable frequency signals across a wide frequency range, available in SPI serial interface. These cost competitive, rugged and compact module are the ideal choice for RF & Microwave systems such as communication systems, test and measurement equipment, radar systems etc.
-
product
Analog Seismic Sensors
Seismometers
Designed to yield the performance needed for scientific studies, our seismometers are used for monitoring long period (very low frequency) signals. These units are often used for earthquake monitoring and for triggering potential alerts during natural disasters such as tsunamis.
-
product
Waveguide Switches
Waveguide switches are electromagnetic switches with hollow circular or rectangular cross-sections and are used for routing RF energy in microwave communications, broadcasting, and in radar applications. Waveguide switches can be used to transfer both power and communication signals, and the bandwidth of a waveguide is in relation to its size, and thus always referred to by its size (e.g. WR112, WR90, WR75 etc.). Compared to coaxial switches, waveguides can route extremely high power signals over a narrow bandwidth at low to high frequencies, and now Lightweight Waveguide series is available.
-
product
Low Noise Amplifiers
LNA amplifier PE15A1000 is rated at 13 Volts DC maximum and 200 mA. Our low noise radio frequency LNA amp is part of over 40,000 RF, microwave and millimeter wave components available from Pasternack. This coaxial millimeter wave low noise amplifier can ship worldwide the same day of the purchase as with our other available RF parts.
-
product
Electromagnetics
Altair software is used across industries to solve a broad range of electromagnetic problems from static to low and high frequencies. Whether your application requires multiple frequency and time-domain techniques with true hybridization to enable efficient exploration of a broad spectrum of electromagnetic performance, or the simulation of magneto static, steady-state and transient conditions, we have the tools you need.
-
product
LCR Meter
TH2817C+
Changzhou Tonghui Electronic Co., Ltd.
■ Freq: 50Hz-100kHz, 10 frequency points ■ Test Accuracy: 0.1% ■ Test Speed: Max.19ms, support low frequency and high speed: TX4+3ms
-
product
FFT Analyzer Software Modules
Metra Mess- und Frequenztechnik in Radebeul e.K.
*Vibration analyzer for low and middle frequencies*Calculates the spectrum of vibration acceleration*VM-FFT+ also for velocity and displacement*RMS and peak spectrum*Envelope spectrum for roller bearing analysis with VM-FFT+*Limit curve with external alarms in VM-FFT+*Power spectral density (PSD) with VM-FFT+*Two measuring cursors for magnitudes and frequencies with snap-in function*Up to four signals per window*One VM-FFT license can be operated simultaneously up to four times with different settings*VM-SCOPE may trigger the frequency analyzer module VM-FFT*External messengers *Offline measurement
-
product
Sub-Harmonic Mixers
Subharmonic mixers are composed of a passive mixer with a subharmonically pumped (×2) local oscillator. These mixers allow designers to use low LO frequency, which eases the need to generate a high frequency LO signal. For high frequency application design, Analog Devices subharmonic mixers offer a simpler alternative to traditional mixers with no LO multiplier.
-
product
Finite Element Method Magnetics Simulation Software
FEMM
Finite Element Method Magnetics
FEMM is a suite of programs for solving low frequency electro magnetic problems on two-dimensional planar and axisymmetric domains. The program currently addresses linear/nonlinear magneto-static problems, linear/nonlinear time harmonic magnetic problems, linear electrostatic problems, and steady-state heat flow problems.
-
product
Field meters
Small, lightweight and low priced non frequency selective Efield meter. It can be used for relatively high field strengths e.g. to observe the field in a TEM cell or a strip line.
-
product
Directional Couplers From 0.01 To 2000 MHz
Pulsar Microwave's low frequency directional couplers operate within the frequency range of 10 kHz to 2 GHz. They're available in either surface mount or connectorized designs. SMA female connectors are standard, but BNC, TNC, F, N, jack or plug are available upon request.Most of these directional couplers have a flatness of +/- 0.25 dB and directivity of 20 dB or better within the operating band. VSWR of 1.3:1 or better maintained on all ports for most models. Maximum power handling is between 1 and 3 watts depending on model.
-
product
Passive Probe, 500 MHz, 10:1, 1 MOhm/10 MOhm
PP020-1
Passive probes are the standard probe provided with most oscilloscopes. Typical passive probes provide a 10:1 attenuation and feature a high input resistance of 10 MΩ. This high input resistance means that passive probes are the ideal tool for low frequency signals since circuit loading at these frequencies is minimized. Passive probes are designed to handle voltages of at least 400V, some as high as 600V. Teledyne LeCroy passive probes feature an attenuation sense pin which tells the oscilloscope to scale the waveforms automatically requiring no user input.Each passive probe is recommended for a certain oscilloscope, using the right passive probe with the right oscilloscope means that the probe will be properly compensated across the entire bandwidth. Using probes with a different oscilloscope will only let you compensate for low frequencies.
-
product
÷10, 500 MHz, 10 MΩ, Passive Probe
PP009-1
Passive probes are the standard probe provided with most oscilloscopes. Typical passive probes provide a 10:1 attenuation and feature a high input resistance of 10 MΩ. This high input resistance means that passive probes are the ideal tool for low frequency signals since circuit loading at these frequencies is minimized. Passive probes are designed to handle voltages of at least 400V, some as high as 600V. Teledyne LeCroy passive probes feature an attenuation sense pin which tells the oscilloscope to scale the waveforms automatically requiring no user input.Each passive probe is recommended for a certain oscilloscope, using the right passive probe with the right oscilloscope means that the probe will be properly compensated across the entire bandwidth. Using probes with a different oscilloscope will only let you compensate for low frequencies.
-
product
Locators
EZiSYSTEM xf-Series
The EZiSYSTEM xf-Series utility locating and tracing equipment makes locating buried utilities easy and efficient. The xf-Series locators have additional low frequencies enabling you to locate and trace utilities over longer distances and in congested environments. With an EZiCAT locator there is no need to manually adjust the sensitivity. With the unique Automatic Pinpointing feature, users can hold press the trigger and start locating.
-
product
Measurement System for ESD Protection
SampleProtect
The SampleProtect measurement system is ready to go, and comes complete with Oxford Instruments’ Cryofree bottom loading cryostat – the OptistatDry BLV, Zurich Instruments’ MFLI Lock-in Amplifier, a specially designed ESD break-out box and high quality measurement grade cables. The patent-pending puck style mounting from Oxford Instruments provides safe installation of your samples. The MFLI 500 kHz Lock-in Amplifier (capable of 500 kHz demodulation as standard) with MF-MD multi-demodulator capability brings the benefits of high performance signal processing at low and medium frequencies. The differential voltage and current inputs of the MFLI are optimised for low noise operation and the high oversampling rate ensures an even better signal to noise ratio. Zurich Instruments’ unique LabOne® control software provides a toolset including an integrated oscilloscope, a spectrum analyser, a plotter and a parameter sweeper.
-
product
8-Channel VME Tachometer
V360
The V360 is a single-width, 6U height VME module designed specifically to acquire low frequency inputs from industrial speed sensors. The module can measure frequency and period over a wide dynamic range, and is specifically designed to ensure reliable measurement in high-noise industrial environments.
-
product
NI-9208, 500 S/s, ±20 mA, 16-Channel C Series Current Input Module
785041-01
500 S/s, ±20 mA, 16-Channel C Series Current Input Module - The NI‑9208 is designed with industrial systems in mind. It includes a high-resolution mode with 50/60 Hz rejection to remove low frequency noise. It has high-channel density to reduce the number of modules needed, which leaves slots open for other measurement types or for reducing the overall per channel cost of the system. The NI‑9208 uses a standard D‑SUB connection for use with cables and connector blocks.
-
product
Carbon-Fiber Reinforced-Polymer Optical Breadboards And Benches
Advanced Photonic Sciences LLC
Carbon fiber optical breadboards provide a similar thermal stability to Super Invar but at a lower cost and are inherently non-magnetic. For ages, steel breadboards have been the only choice; however, structures made from carbon fiber reinforced polymer (CFRP) have been used in the aerospace and space industries for many years due to their low weight, high strength, excellent thermal stability and low resonant frequencies. APS now brings this advanced technology to the world of photonics in the United States and Canada with carbon fiber breadboards from CarbonVision. Four grades of carbon fiber breadboard are offered: the economic EC-Series, the advanced AD-Series, the all-carbon AC-Series, and the slim SL-Series.
-
product
RFID
LF (125 kHz)
BIS L uses a low frequency (LF) of 125 kHz with passive data carriers. These data carriers are read/write, designed for use in harsh environments and chemically highly resistant. With BIS L you can handle applications with special demands economically. Small form factors and versions with enhanced data security (additional check code) also provide great flexibility.
-
product
High Voltage Switching Test System
The advanced development of new technologies, such as SiC and GaN, have opened the opportunity for more efficient and higher voltage/power performance in switching and power management circuits. Their high cutoff frequencies, low on-state resistance, and very high breakdown voltages can increase power supply power handling densities approaching hundreds of watts/inch. Reliability of these new technologies and techniques is critical for realizing practical applications. While Silicon devices have a rich history of proven reliability, these newer compound semiconductor technologies are too new to have a reliability history and have not been well proven. Further, process variations, even in well-controlled lines, yield widely varying results. This has driven the need for additional testing and to burn-in devices prior to delivery.
-
product
NI-9208, 500 S/s, ±20 mA, 16-Channel C Series Current Input Module
780968-02
500 S/s, ±20 mA, 16-Channel C Series Current Input Module - The NI‑9208 is designed with industrial systems in mind. It includes a high-resolution mode with 50/60 Hz rejection to remove low frequency noise. It has high-channel density to reduce the number of modules needed, which leaves slots open for other measurement types or for reducing the overall per channel cost of the system. The NI‑9208 uses a standard D‑SUB connection for use with cables and connector blocks.
-
product
AC Current Sensor
LFR
The LFR ac current probe has been designed to have market leading low frequency performance, meaning low phase shift and low noise. This compact, low cost, clip-around probe is both flexible and dual-range, and is optimized to give minimal phase measurement error at frequencies from 45Hz to 20kHz and have a very low noise floor.
-
product
Low Frequency RF Impendence Transformers
0 kHz to 3 MHz 100W - 4000W 1 input, up to 7 outputs Step-Up / Step-Down Transformers Impedance matching outputs from 1.2 Ohms to 2500 Ohms Compact Design Compatible with T&C''s Class A 10 kHz - 20 MHz LF Generators & Amps Compatible with Class B 20 kHz - 6 MHz LF Generators & Amps
-
product
Compact Receiver Module
MixAMC-I
Virginia Diodes'' standard Spectrum Analyzer Extension Modules (SAXs) provide high performance broadband down-conversion and frequency extension of microwave specturm analyzers into the THz range. VDI now offers integrated MixAMC modules that provide industry leading performance in a compact package. These integrated MixAMC modules are used to down-convert millimeter-wave / THz signals only. Spectrum Analyzer Extension mode is not currently available for the MixAMC-I products. Integrated MixAMC modules utilize a low frequency LO input (<20 GHz) and have a seprate IF output port. Integrated MixAMC modules configured for high IF bandwidth may be available upon request.
