D-Sub
D-Subminature Connector Also known as: DSub
-
Product
37-Pin D-Type Female Solder Pin HV
40-960-037-F-HV
D-Sub Female Connector
This connector is designed to allow users to directly terminate cables with soldered connections.
-
Product
37-Pin D-Type Male Solder Pin HV
92-960-037-MHV
D-Sub Male Connector
This accessory is designed to allow users to directly terminate a cable with soldered connections. When the product is used without a backshell users should make their own cable strain relief arrangements and ensure appropriate electrical safety precautions are observed.
-
Product
9 Pin D-Type, Male, Straight PCB Mount, HV
40-963-009-SM-HV
D-Sub PCB-Mount Connector
9-Pin Male D-Type Connector, High Voltage - Straight PCB Mount
-
Product
Cable Assembly, Receiver, TriPaddle, 20", 50-Pin Female D-Sub
540018010101
Cable Assembly
Cable Assembly, Receiver, TriPaddle, 20", 50-Pin Female D-Sub
-
Product
16 Hole Back Extension
9561-BE
-
Enclosed version of the cabling "doghouse" for the Hawk/PC chassis with rear panel punched to accommodate 16 50/37 pin d-sub connectors. Hinged for access to the rear of the DG-style backplane.
-
Product
3-Pin Power D-Type Connector, 40A, Female Without Backshell
92-960-003-F
D-Sub Female Connector
This connector is suitable for Pickering Interface's modules that use the 3-Pin Power D-Type connector. It is designed to allow users to make a direct termination with soldered connections.
-
Product
SHC68-68, 68-Pin VHDCI Male to 68-Pin D-SUB Female, Twisted Pair, Basic Shielded Multifunction Cable, 2m
191945-02
Multifunction Cable
68-Pin Male VHDCI to 68-Pin Female D-SUB, Twisted Pair Cable with Basic Shielding, 2m
-
Product
NI CAN Cable, No Term, High-Speed/FD/Low-Speed, D-Sub 9-Pin F, 1m
193128-01
CAN Cable
9-Pin Female D-SUB to 9-Pin Female D-SUB CAN Cable - The DB9F-DB9F CAN Cable connects C Series CAN Interface Modules, C Series LIN Interface Modules, or C Series Multiprotocol Interface Modules to devices, breakout boxes, and accessories. It is sometimes referred to as CAN Cable (single termination or no termination). This cable is compatible with high-speed, flexible data-rate, and low-speed/fault tolerant CAN signals, available with or without termination, and in different lengths.
-
Product
X13 GPIB Cable, MicroD25 to Shielded cable/Standard connector, 2M
183285-02
GPIB Cable
24-Pin Male/Female GPIB to 25-Pin Male Micro D-SUB GPIB Cable - The 24M-24F-MicroDB25M X13 GPIB Cable, sometimes referred to as the X13 cable, connects your system to GPIB devices or interfaces for instrument control. This standard shielded cable can connect PXI Controllers to instrument control devices and is offered in different lengths.
-
Product
Connector Block, 50-Pin D-Type, Female
40-965A-050-F
Connector Block
The 40-965A-050-F connector block provides a simple method of connecting to 50-Pin D-Type connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage. PTFE cables are recommended for use with this connector block to maximise copper cross-sectional area and insulation properties. Connector blocks have higher losses than a cable connection and the breakdown voltage is controlled by clearances to the metal shell. The metal shell includes an internal insulation barrier under the carrier board.
-
Product
9-Pin D-Type Male, Solder Bucket, HV
92-960-009-M-HV
D-Sub Male Connector
9-Pin Male D-Type Connector, High Voltage, Solder Bucket - Without Backshell
-
Product
3-Pin Power D-Type Connector, 40A, Female PCB Mount
40-963-003-RF
D-Sub PCB-Mount Connector
This connector is suitable for Pickering Interface's modules that use the 3-Pin Power D-Type connector. It is designed to allow users to make a termination via a PCB.
-
Product
CB-37FH, DIN-Rail Vertical Mount 37-Pin Spring TB
778685-01
Terminal Block
37-Pin Female D-SUB to 37-Pin Female Screw Terminal, Vertical DIN Rail Terminal Block - The CB-37FH is an unshielded connector block that provides access to NI data acquisition devices with 37-pin D-SUB connectors. The CB-37FH is a vertical connector block that mounts perpendicular … to the DIN rail. It features screw terminals for connecting to 37 I/O signals, 12 to 30 AWG.
-
Product
Cable Assembly, Reveiver, 36", QuadraPaddle, 4 x 50-Pin FML D-Sub
540142020240
Cable Assembly
Cable Assembly, Reveiver, 36", QuadraPaddle, 4 x 50-Pin FML D-Sub
-
Product
IBM AT/ISA, Vectorbord Plugbord
4617-3
-
VECTOR Electronics and Technology, Inc.
98 contacts (49 each side) on 0.100" centers. Pad per hole. Voltage and ground buses around board perimeter. I/O mounting area for up to 70-pin D-sub and ribboncable connectors. Mounting bracket and hardware kit included (P/N HD36B).
-
Product
IBM PC-XT, Vectorbord Plugbord
4613-3
-
VECTOR Electronics and Technology, Inc.
62 contacts (31 each side) on 0.100" centers. Pad per hole. Voltage and ground buses around board perimeter. I/O mounting area for 37-pin D-sub and ribbon cable connectors. Mounting bracket and hardware kit included (P/N HD36B).
-
Product
9-Pin D-Type Connector Block
92-965-009-F
Connector Block
This connector block provides a simple method of connecting to 9-Pin D-Type connectors. The screw terminals use a rising cage screw clamp mechanism to minimize risk of copper strand breakage.
-
Product
96 Channel DPST Relay And Control PXI Carrier Card
GX6196
Relay
The GX6196 is a 6U PXI switch and control board that can be used to create custom switching, signal conditioning, or specific UUT control interfaces. The board provides 96, 2 pole, form A relays, 8 digital I/O lines, and a serial digital interface. All of these resources are available via (5) inter-board connectors which interface to the user defined daughter / mezzanine board. The mezzanine board provides all connections to the unit under test (UUT) via two 78 pin D-sub connectors. The GX6196 is supplied with a front panel which accepts (2) 78 pin D-sub connectors.
-
Product
CB-37FH, DIN-Rail Horizontal Mount 37-Pin Spring TB
778676-01
Terminal Block
37-Pin Female D-SUB to 37-Pin Female Connector, Horizontal DIN-Rail Terminal Block - The CB-37FH is an unshielded terminal block that provides access to NI data acquisition devices with 37-pin female D-SUB connectors. The CB-37FH mounts in line with the DIN rail, and it featuresscrew or spring terminals for connecting to 37 I/O signals, 12 to 30 AWG.
-
Product
Cable Assembly, Receiver, TriPaddle, 20", 50 Pin ML D-Sub
540019020101
Cable Assembly
Cable Assembly, Receiver, TriPaddle, 20", 50 Pin ML D-Sub.
-
Product
26-Pin D-Type Female Straight PCB Mount
40-963-026-SF
D-Sub PCB-Mount Connector
Accessory allows a user to create their own PCB based termination solution mounted directly on the front of the product or on the end of a cable. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires.
-
Product
Cable
RCONQPMC-4
-
RCONQPMC-4 - Transitions from a SCSI-68 pin connector to eight CJ70 Twinax, 3 lug, 1553 cable jack ends and one D-Sub 50 pin connector for additional I/O.
-
Product
3-m, 50-pin Dsub Cable
Y1136A
Multifunction Cable
Connect this m/f twisted pair with outer shield cable to 34980A multifunction switch/measure mainframe and modules
-
Product
50-Pin D-Type Connector, Right Angle PCB
40-963-050-RF
D-Sub PCB-Mount Connector
Accessory allows a user to create their own PCB based termination solution mounted directly on the front of the product or on the end of a cable. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires.
-
Product
DB25F-DB25M, Low Profile I/O Cable, 25-Pin Female DSUB to Male DSUB (1m)
154742-01
Multifunction Cable
Low Profile I/O Cable, 25-Pin Female DSUB to Male DSUB (1m)
-
Product
Video Signal Distributor
MSVD-250N
-
MSVD-250N is a Analog Distributor Buffer that distribute one (1) input signal to the 5/10/15/20 channels. User can select input type between 15P D-Sub and 5 BNC (R,G,B,HS,VS). The distribution buffer can be used in factory assembly lines, repair depots, and for system integration to save cost and time.
-
Product
Audio Card I/O Modules
PIM481-J/DSUB
-
The PIM481-J PMC I/O Module, with four 3.5mm stereo connectors and the PIM481-DSUB PMC I/O Module, with D-sub for rear I/O can be mounted on a rear transition module (RTM).
-
Product
Cable Assembly, Receiver, 36", TriPaddle, 9 Pin FML D-Sub
540010020201
Cable Assembly
Cable Assembly, Receiver, 36", TriPaddle, 9 Pin FML D-Sub.
-
Product
15-Pin D-Type Connector, Male
40-963-015-SM
D-Sub Male Connector
Accessory allows a user to create their own PCB based termination solution mounted directly on the front of the product or on the end of a cable. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires. 15-Pin Female connectors can be directly mated to a corresponding Pickering Switching Module while Male versions can be used to interface to a Female cable assembly termination.
-
