Bare board Fixtures
accurately position and retain unloaded PCBs.
See Also: Bare Board Testers, Board Test Fixtures, Bare Board
-
Product
PCIe Digital I/O Board, 64 Optically Isolated I/O Channels, 5V-HS
APCIE-1564-5V-HS
-
32 digital inputs, 5 V, isolated16 interruptible inputs32 digital outputs, 5 V, isolated, 10 to 36 V, 500 mA/channelOptical isolation 1000 VWatchdog for resetting the outputs to "0" (when Power-On)Protection against fast transients, overvoltage, electrostatic discharge and high-frequency EMIInputs: voltage reversal, input filtersOutputs protected against short circuitOvertemperature and overvoltage protectionDiagnostic report in case of short circuits, overtemperature, voltage drop ...24 V power outputs with protection diodesShutdown logic when the external supply voltage drops below 5 V
-
Product
Advanced Programmable IO Board
MS 1508
-
- 32 Bit ARM9 LPC3250 Processor (256KB SRAM)- External memory (Flash – 2 MB, RAM - 512 KB, 8KB DPRAM)- 10/100 MBPS Ethernet Interface- USB 2.0 Host/Device Interface- 144 Digital IO Channels – (18 * 8 Configurable Ports)- 64 Analog Inputs (16 Bit, 1MSPS)- 16 Analog Outputs (16 Bit)- 2 RS232 Serial Ports- High Speed Logic Device with 1 M bit in system flash, 54Kbit - Block Ram and 11Kbit Distributed Ram- Power, Analog and Digital signals Interface Connectors (J1, J2 and J3 - 96 Pin Euro)- Data acquisition of all analog & digital channels- External Bus through Add on module (15 bit address bus and 16 bit data bus)- Transmission of 1Kbytes at 400us through Ethernet- Power Requirements: +15V/2.5A, -15V/2.5A and +5V/6A- Board Dimension is 366.72mm x 150mm- Portable and 9U 19” chassis mountable- Board has interface connectors in rear side as well as in front side- J1, J2 and J3 96 Pin Euro connectors at rear side and Ethernet, JTAG, RS232, USB connectors at front side
-
Product
6U VPX Single Board Computer
VP62007
-
LinkedHope Intelligent Technologies Co.,Ltd.
VP62007 is a 6U VPX single board computer designed by LinkedHope® based on Intel® QM170/CM236 chipset. The compact and space-saving processor board meets the VITA46.0 specifications. VP62007 provides 4 x4 SRIO2.1 for VPX Data Plane communication, 2 x8 PCIe for VPX Expansion Plane communication, 4 GbE for VPX Control Plane communication. Rich data exchange interfaces on VP62007 make it easy to build box-level or system-level solutions.
-
Product
DB25 DIN-Rail Wiring Board
ADAM-3925
-
Low cost universal DIN-rail mounting screw terminal module for PC-LabCard products with DB25 connectorScrew-clamp terminal blocks allow easy and reliable connectionsCase dimensions (W x L x H): 77.5 x 56.3 x 51 mm (3.1" x 2.2" x 2.0")To Be Used With PCI-1757UP, PCL-833
-
Product
Single Board Computer
VME-1909
-
Curtiss-Wright Defense Solutions
The VME-1909 from Curtiss-Wright Defense Solutions is designed to be a low cost, high performance technology insertion Single Board Computer (SBC). Pin-compatible with many previous generations of Curtiss-Wright SBCs, the VME-1909 offers increased computing performance with today’s latest software advances.
-
Product
Hall Sensor Board with I2C Interface
050-280
-
Version: +24V/60A -24V/60A -5,2V/90A -2V/25A The Hall-Sensor Board is the right accessory for your system in combination with the Elma SysMon. It's possible to measure up to 4 currents and to monitor them with the Elma SysMon 3 Gen.
-
Product
CableEye 4-Wire Calibration Verification Board | Cable & Harness Testers
CB52
-
The CB52 is intended for periodic calibration verification of the Kelvin 4-wire resistance measurement module – an optional, add-on module that may be purchased with any new hipot system, or added to an existing high voltage tester as an upgrade.
-
Product
GPS/FMS Universal Test Fixture
TA-3000
-
This panel was designed to give the avionics shop the capability to test and troubleshoot many of the GPS, GPS/COMM and FMS units on the market today. Breakout jacks are provided for both analog and digital signals that need to be monitored or simulated. A data port update jack is provided as well as Arinc 429 and RS232 loopback switches. Switches for Gillham altitude are provided as well as fuel flow adjustments. An array of annunciators and configuration switches are also provided to verify those outputs and inputs. Optional UUT configuration overlays also availabl
-
Product
Isolated Programmable Multifunction Counter Board
APCI-1710
-
Wide application possibilities through free combination4 modules with numerous functions quickly and easily programmableEach of the 4 modules is programmed with a function. The 4 modules can either be programmed with the same function or freely be combined with 4 different functions.
-
Product
AMD Zynq™ UltraScale+™ MPSoC XMC Board
IC-MPS-XMCa
-
The IC-MPS-XMCa is a XMC FPGA card based on the AMD Zynq™ Ultrascale+™ ZU4CG MultiProcessor SoC.
-
Product
6U OpenVPX Single Board Computer (SBC)
67PPC2
-
The 67PPC2 is a 6U OpenVPX NXP® PowerPC based Single Board Computer that can be configured with up to six NAI smart I/O and communication function modules. Ideally suited for rugged Mil-Aero applications, the 67PPC2 delivers off-the-shelf solutions that accelerate deployment of SWaP-optimized systems in air, land and sea applications.
-
Product
Single Board Computers (SBC)
-
Any Single Board Computer from WinSystems is an Off-the-shelf ARM and Embedded PC designed for rugged, industrial environments and long product life cycles. Our Single Board Computers are created and packaged under precisely controlled conditions and subjected to intensive quality control to ensure they perform under extreme conditions.
-
Product
PCI Express UltraScale+ FPGA Carrier Board With FMC+ Site, X16 PCIe Gen 4
PG4+
-
The PG4+ continues DEG’s commitment to delivering high performance processing solutions for mission critical applications requiring the latest in AMD UltraScale+ FPGA computing power. The PG4+ is a PCI Express, standard form factor, FPGA processor board designed to meet the needs of challenging, embedded high-performance digital signal processing applications. The AMD UltraScale+ VU37P or VU47P delivers superior processing capabilities and supports operations such as: FFTs, FIR filters, fixed-point and repetitive processing tasks. The PG4+ FPGA node processes input from the FMC HPC + (Vita 57.4) site, allowing for maximum application configurability and performance when coupled with DEG’s market leading ADC and DAC FMC modules that operate up to 12 GSPS.
-
Product
8 Channel Sample & Hold and Signal Conditioning Board
-
Same features of 8 Channel Sample & Hold and Signal Conditioning Board plus connection and transient protection for Group3 B (digital) and D (analog output) boards.
-
Product
Composite 1×24 Video Distribution Amplifier Board
BL-VDA124-01
-
Video Distribution Amplifiers (sometimes called a video splitter – not to be confused with a video split screen controller such as our PXD510E split screen controller) are typically used for connecting a camera or other video source to several monitors that do not have “looping” inputs. In this situation, each monitor has a permanent 75 ohm termination. With two non-looping monitors connected together, the line would be double loaded and result in a dim picture on each monitor. Using a Video Distribution Amplifier will solve this problem by driving each monitor individually at 100%.
-
Product
Airborne Video Delay Board
MS 2006
-
- Spartan FPGA based Design- Customized design for delaying & switching video inputs to RF section- Interface with EW Signal Processor Unit- Two channel video inputs and control- Video Signal Delay from 1ns to 1ms- Over duty Indications- Inhibit Control- Discrete Interface
-
-
Product
SPARK PC Development System for PCIe Cobalt, Onyx, Flexor and Jade Boards
Model 8266
-
The SPARK® Model 8266 is a fully-integrated PC development system for Pentek Cobalt®, Onyx®, Flexor®, and Jade™ PCI Express (PCIe) software radio, data acquisition, and I/O boards. It was created to save engineers and system integrators the time and expense associated with building and testing a development system that ensures optimum performance of Pentek boards.
-
Product
Four Channel Relay Board for Power Supply Isolation
FXA-113 PSU Relay 4CH
-
The FXA-113 is a four-channel relay board designed as an output disconnect option for laboratory power supplies. Especially in ICT applications it’s important, that the power supply is completely isolated from the DUT during measurements. Therefor each channel features two high current relays for the power path and two reed relays for the sense path. All four channels are equipped with a status led and can be switched independently. In addition, it is delivered with an installed DIN rail carrier.
-
Product
2MP HDR Jetson TX2/TX1 Camera Board
E-CAM20_CUTX2
-
e-CAM20_CUTX2 is a 2MP HDR camera board for NVIDIA® Jetson TX2 /TX1 developer kit. It has an ability to stream seamlessly at wide temperature range (-40°C to 85°C). It enables an excellent low-light performance and can capture images even under 0.5 lux. e-CAM20_CUTX2 is based on 1/2.7" AR0230AT CMOS image sensor from ON Semiconductor™. It has S-mount (M12) lens holder which allows customers to choose and use the lens according to their requirement.
-
Product
Meter Test Board
MTB
-
The accuracy of TESCO’s Meter Test Board (MTB-3050) is now available in multi-position test boards to perform individual or simultaneous accuracy tests in the meter shop!
-
Product
PCI Counter/Timer with Quadrature Board
APC483
-
Several models with a variety of configurations provide up to ten counter/timer channels for counting events, generating waveform control signals, measuring pulse-widths, periodic rates, or quadrature position and monitoring operations.
-
-
Product
PCI Express Digital I/O Boards
PEX-P16R16i
-
PCI Express x1, 16-channel Isolated Digital Input, 16-channel Relay Output Includes one CA-4037W cable and two CA-4002 D-Sub connectors, supports operating temperatures from 0 ~ 60°C. (Formerly PISO-P16R16E).
-
Product
In-Line Functional Test Fixtures
-
Add an advantage to in-line production with fast change over interchangeable fixturing. Circuit Check’s in-line board handlers and in-line board handler fixturing exceed the high performance requirements associated with high-volume production. Circuit Check supports in-line fixturing for all the leading handlers.
-
Product
Becker NAV/RMU/RMI/OBS Test Fixture
TA-3320
-
This NAV test fixture is specific to the requirements for testing Becker Avionics NAV, RMI and RMU products. The panel incorporates specific functionality required for testing these Becker products by the book including special requirements for the RMU 5000 and the IN 3300 series of nav indicators. This BAEE NAV test fixture also facilitates resolver alignment and discrete meter testing through the PG 3300 interface connector. The RM 3300 portion of the panel tests the Becker RMI indicators and allows for sourcing the composite signal from the paired radio or from an external generator. The DME channeling outputs are monitored with discrete LED's as well as the ILS, V/LOC, Glideslope and NAV TEST valids. Discrete test jacks are provided for all the meters and the resolver of the NAV indicator and a dimming source is also provided. When testing the RMU 5000 computer access is through a dedicated connector.
-
Product
Digital I/O Board, 16 Optically Isolated I/O Channels, 24V
APCI-1516
-
PCI interface to the 32-bit data bus? 8 isolated input channels, 24 V? 8 isolated output channels, 10 to 36 V,output current 500 mA? Timer-programmable watchdog for the reset of the outputs to ??? One ground line for all inputs and one ground line for all outputs? Outputs set to "0" at PowerOn/Reset
-
Product
PC/104 Multifunction Analog I/O Boards
104-AIO16A/E
-
The 104-AIO16A is a high-performance 16-bit resolution PC/104 board which provides speeds up to 500kHz for 16 single-ended or 8 true differential analog input channels. This multifunction board features an excellent price/performance value for precision PC/104-based data acquisition, control, or signal analysis of standalone environmental test stations, compact production test equipment, portable testers, avionics and other applications.
-
Product
PXI Express Board Virtex-5 ADC Module
SMT790
-
Sundance Multiprocessor Technology Ltd.
The SMT700 is one of the first of a new range of Sundance cards that includes a direct connection to SLB (Sundance Local Bus) compatible mezzanine card, without the need for a Sundance TIM. This enables a variety of cards to be added to a system, for example extra Ethernet ports, video in/out, High speed ADC / DAC etc. Data from these extra cards (along with data from the SMT700’s own inputs – up to 1Gb/s Ethernet, 2.5Gb/s optical links, and RSL links) can be processed via the Virtex 5, or by another linked card or module.
-
Product
Power Interface Board 3U, 2PSU connectors with AC pins
106PIBM302-9001R
-
The PIB 3U 2 slot has two power connector P47 with AC pins and connects to the backplane via power bugs with 6/32 screws. It is used to facilitate pluggable power supplies, headers, and utility connectors.
