GR Fixtures
A device or setup created by Genrad (now Teradyne) used to perform a test case on.
See Also: Genrad
-
Product
Wireless Test Fixtures
-
At Forwessun, we have vast experience in designing and delivering wireless in-circuit test (ICT) fixtures. We have experience in providing fixtures tailored to the unique needs of various different industries. While our primary customer focus has been on full and half-bank fixtures for the HP3070 system, we offer bespoke solutions for other platforms as well including GenRad, Teradyne, and SPEA systems.
-
Product
2-kbit 12C EEPROM for Fixture Coding
FXA-101 I2C EEPROM
-
The FXA-101 is a 2-kbit serial I²C bus EEPROM used for identification of systems components. With it’s DIP switch it’s easily addressable. The FXA-101 may be glued directly to the appropriate component or inserted into a UMK housing from Phoenix Contact and installed on a DIN rail.
-
Product
Latch-on Test Fixtures
-
Latch-on Test Fixtures provide a convenient way for production personnel to quickly and reliably make electrical connections to a product for programming or final test. These custom fixtures eliminate the need to hand-wire products in order to power them up and communicate with them. Typical applications for latch-on test fixtures are metering devices, control panels, and any type of controls that connect via terminal strips.
-
Product
Audio Panel/Amplifier Test Fixture
TA-200
-
The Model TA-200 test panel was designed to allow Avionics shops the capability to test and troubleshoot both today's new generation audio panels as well as the standard audio panels of the past. The testing of these panels over the years has always proven to be a very time consuming job for most shops because of the limited capabilities of any past test panels.
-
Product
ICT/FCT-Fixtures, Max UUT 370 × 300 mm (wxd)
CK-2 Medium (Hold Down Gate) / 230156
-
The series of In-Circuit testers that are Teradyne for the 228x and TestStation are dedicated tools that rely on the tester hardware for diagnostics and test pattern delivery. The integration of the stand-alone BTS with the Teradyne ICT can enhance the system’s capability. In other words, it can provide access to additional tools. It provides the user with a common platform and portability of test patterns from stand-alone to ICT and later on to functional test and depot test stations.
-
Product
RF Shielded Fixture
-
A semi-automatic, pneumatically operated fixture with a sliding pressure top provides a very short mechanical cycle-time. The unit is prepared for full, multi-station automatic operation using a centrally placed robot arm for UUT load/unload.
-
Product
Current Probe Calibration Fixtures
-
Calibration fixtures are used for calibration of Coupling Loss/Transfer Impedance of current probes and BCI probes, as well as for the calibration of test levels for conducted immunity/susceptibility tests using BCI probes.
-
Product
High Node Count In-Circuit Test Fixtures
HNC Test Fixture
-
Circuit Check continues to be a leading edge provider of custom engineered test solutions with our new Keysight i3070 HNC test fixture. Working with Keysight Technologies during the development of their HNC adapter in 2011, we were the first test fixture provider to offer customers with a solution to test large node count boards. High node count test fixtures can handle greater than 10,000 probes.
-
Product
Standard RF Fixture
-
The standard RF fixture supports both pulsed and non-pulsed operation. It employs SMA input/output connections. For RF output powers over 10W, an N-type connector may be used to replaces the SMA connector because of its power-handling capability.
-
Product
Pre-configured Power Device Analyzer / Curve Tracer (B1505A with modules and fixture)
B1505AP
-
B1505AP provides eight different pre-configured packages that satisfy a wide variety of power device measurement requirements. The package can be selected according to voltage / current range and the requirement for capacitance measurement.
-
Product
In-Circuit Test Fixture Design Services
-
An integral part of board test is the test fixture. Innovations in board technology may manifest themselves as challenges in test fixture design. Utilizing a creative & systematic design philosophy, Acculogic consistently delivers state of the art solutions for the most complex test interface problems.
-
Product
Dual Servo Electrical Test Fixture
TA-334001
-
The TA-334001 is a Dual Servo Electrical Test Fixture made to be an equivalent substitute for the Honeywell test fixture T-334001. The test fixture front panel duplicates all the proper switch numbers and descriptions so the technician can follow by the book testing. The panel overlay text is reverse screened (backside) to insure that text quality will not degrade over time. All the appropriate test jacks are provided on the panel for servo pin and bracket breakouts. This fixture provides for the switching of motor direction, clutch, tach selection, synchro selection, limit switching and polarity relays. Panel meters are provided on the test fixture so that the technician can monitor the servomotor voltage as well as clutch voltage and current.
-
Product
Wireless In-Circuit Test Fixtures
-
Higher density more complex circuit boards complicate testing requirements while smaller more tightly spaced test pads create a wiring challenge for the fixture fabricators, test engineers and maintenance personnel. Wireless fixtures solve the challenges associated with the nest of wires found in standard long wire fixtures. Wireless fixtures replace the “nest” of wires with copper traces on a multilayered printed circuit board called a Translator Board or T-Board®. Circuit Check’s wireless fixture technologies reduce test program debug and maintenance times while easing the ECO process. Thus allowing for the higher level of test performance, the ability to probe smaller denser targets and achieve ultra-high node counts.
-
Product
Magnetizing Fixtures
-
Usually, the magnetizing fixture (coil) is specifically designed for the task of the customer and the product.In the simplest case, only the necessary parameters for the dimensions of the component are calculated for an axial coil, and the device can be designed and manufactured according to standard procedures.
-
Product
Universal Breakout Test Fixture
CA-323
-
The CA-323 Universal Breakout test fixture was designed to provide, as the name suggests, a universal test solution for aircraft trouble-shooting. The unit gives the technician the ability to monitor (100) different conductors or open an individual conductor for simulation or measurement. Any avionics component can be extended and in many cases with only a voltmeter and oscilloscope the operation in question of the Unit Under Test can be determined.
-
-
-
-
Product
Manual Fixture Kit
230354 – CMK-05
-
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
Product
Clamshell Type Mechanical Fixtures
-
Known in the ATE Industry as “Clamshell” type Test Fixtures, Semco’s Mechanical Test Fixture line is a cost-effective solution to test Printed Circuit Boards and Assemblies. This Test Fixture line is also available with the most widely used interfaces in the test industry.
-
Product
Manual Fixture Kit
230351 – CMK-02
-
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
Product
Bottom Electrode SMD Test Fixture
16197A
-
The 16197A is designed for impedance evaluations of bottom electrode SMDs. It achieves stable frequency characteristics up to 3 GHz and provides highly repeatable measurements. The Keysight 16197A supports various SMD sizes, as small as 1005 (mm)/0402 (inch) and as large as 3225 (mm)/1210 (inch). Accommodation of the 0603 (mm)/0201 (inch) size is available with option 001.
-
Product
In-Line Functional Test Fixtures
-
Add an advantage to in-line production with fast change over interchangeable fixturing. Circuit Check’s in-line board handlers and in-line board handler fixturing exceed the high performance requirements associated with high-volume production. Circuit Check supports in-line fixturing for all the leading handlers.
-
-
Product
ICT/FCT-Fixtures, Max UUT 370 × 300 mm (wxd)
CK-2-228X (Small IF) / 230540
-
The series of In-Circuit testers that are Teradyne for the 228x and TestStation are dedicated tools that rely on the tester hardware for diagnostics and test pattern delivery. The integration of the stand-alone BTS with the Teradyne ICT can enhance the system’s capability. In other words, it can provide access to additional tools. It provides the user with a common platform and portability of test patterns from stand-alone to ICT and later on to functional test and depot test stations.
-
Product
28 cm2 Test Fixture Operations Kit
-
The 28 cm2 Cell Test Manifold Kit offers a highly effective solution for testing of individual planar solid oxide fuel cells. The kit contains all items necessary to easily mount cells with ~100 cm2 substrates. Designed for both long and short term experiments to measure properties such as fuel utilization, thermal gradients, red-ox cycling and longevity/degradation, these kits will accelerate your research and development activities.
-
Product
In-Circuit Fixtures
-
In-Circuit test fixtures can be configured for dual stage, dual well and opens testing applications. Even the most complex boards can be accommodated using standard methods of actuation.
-
Product
Environmental Functional Test Fixtures
-
Circuit Check builds test fixtures for Halt/Hass testing whether a fixture is used within an environmental chamber or is a standalone fixture. Circuit Check has the capability to manufacture these types of fixtures.
-
Product
USB Type-C Test Fixture | CB26U | Cable Harness Tester
-
A leader in development of PC-based cable and wire harness, continuity, resistance and hipot test systems for over 20 years, CAMI offers the CableEye suite of products complete with accessories – including “connector boards”. The selection of these test fixture boards is constantly growing and is currently numbering over 60 – most of which are populated with ‘families’ of connectors. When pre-populated boards are used, the tester GUI automatically displays a graphic of the connectors under test.
-
Product
Test Fixturing Solutions
-
Amfax and MAC Panel have teamed up to provide a unique WIRE-FREE Test fixture technology. We have created an alternative solution to traditional wired ITAs called PECture(TM). The name is a combination of PEC (Printed Electronic Circuit) and fixture.
