-
-
Product
Double Ridged Waveguide Horn
QRH400
-
Frequency range: 400 MHz - 6 GHz VSWR (max): < 2.3 :1Impedance: 50 O (Ohm)Connector: 2xN female Power (CW / Peak): 350 W / 350 W
-
Product
H Bend Waveguides
-
H-plane waveguide bends are sections of high-precision crafted waveguides and shaped to either 30º, 45º ,60º, or 90º angles. It directs the radio frequency beam and "bends" the signal to go the direction you want.View more H-Bend Waveguide
-
Product
Waveguide Power Dividers
-
2-way power divider that operates from 220 to 330 GHz. The power divider offers a typical insertion loss of 2.3 dB and typical isolation of 20 dB. All ports are well-balanced and in-phase for power dividing or combining applications across the band. The power divider is configured as a right-angle package with WR-03 waveguides and UG-387/U-M anti-cocking flanges at all ports.
-
Product
Waveguide Harmonic Mixer, 26.5 to 40 GHz
11970A
-
The Keysight 11970A waveguide mixer is a general-purpose harmonic mixer employing a dual-diode design to achieve flat frequency response and low conversion loss. These are achieved without external dc bias or tuning stubs. Manual operation and computer-controlled hardware operation are simplified because mixer bias and tuning adjustment are not required.
-
Product
Waveguide Harmonic Mixers (smart mixer), 75 to 110 GHz
M1970W
-
The Keysight M1970W 75 to 110 GHz waveguide harmonic mixer is an un-preselected mixer that will extend the operating frequency range of N9030A PXA, N9020A MXA,and N9010A EXAsignal analyzers up to 110 GHz. Smart features are embedded to help you to greatly simplify your overall test setup and improve your DANL and TOI of your test system. Go smart with harmonic mixing for your millimeter-wave applications.
-
Product
Waveguide Variable Attenuators
-
A variable attenuator from Pasternack. This SMA microwave attenuator is a continuously variable attenuator design.
-
Product
Coaxial Waveguide Adapter, 1.0 mm (m), 75 to 110 GHz
W281D
-
The Keysight W281D is a 1-mm male to W-band waveguide adapter with a frequency range of 75 GHz to 110 GHz. The Keysight W281D is used with the Keysight 8510XF systems.
-
Product
Double Ridged Waveguide Horn
DRH203
-
Frequency range: 200 MHz - 3 GHz VSWR (max): < 1.6:1Impedance: 50 O (Ohm)Connector: N female Power (CW / Peak): 400 W / 750 W
-
Product
Waveguide Power Sensor
-
Make accurate and reliable measurements in the 50 to 110 GHz frequency range. Keysight's waveguide power sensors offer best SWR, high reliability and low loss, and come with a 50 MHz calibration port to reduce measurement uncertainties.
-
Product
Waveguide Detectors 26.5 to 110 GHz
-
Our waveguide detectors cover a broad frequency range of 26.5 GHz to 110 GHz and are available with waveguide sizes ranging from WR-28 to WR-10. The video output ports utilize SMA female connectors. These high performance zero-biased waveguide detectors exhibit excellent performance in Ka, Q, U, V, E and W frequency bands. These types of waveguide detectors are commonly used in various aerospace, defense and commercial wireless applications used in instrumentation, power detection, power monitoring, direct detection receivers, high frequency communications, radar, SATCOM, point-to-point radio, telecom, data links and R&D. The detector circuits use high performance GaAs Schottky Barrier Beam lead diodes with extremely low junction capacitance. These waveguide detector designs perform with minimal sensitivity variation resulting in a flat frequency response across the entire waveguide band. All of the waveguide detectors are in-stock and ready to ship.
-
Product
Waveguide Electromechanical Relay Switches C, X, Ku, K & Ka Bands up to 40 GHz
-
Waveguide Electromechanical Switch models cover C, X, Ku, K, Ka frequency bands up to 40 GHz. SPDT and Optional DPDT* Configurations with Latching Self Cut-Off Actuators, TTL Logic, and Position Indictors with manual override. Patented Motor Drive with Arc Suppression. Designs support WR-137, WR-112, WR-90, WR-75, WR-62, WR-42, and WR-28 waveguide sizes with O Rings for pressurized operation. Power handling capability up to 12 kW CW and 320 kW Peak. These waveguide electromechanical relay switches deliver desirable performance that includes high isolation levels up to 105 dB, and extremely low insertion loss down to 0.01 dB.
-
Product
WR-12 Waveguide Straight
WAG-12-SXX
-
• 60 GHz to 90 GHz• Low Insertion Loss, typical for length• Low Return Loss, typical for length• UG-387 flangeView more WR-12 Waveguide Straight
-
Product
Coaxial Waveguide Adapter, APC-7, 12.4 to 18 GHz
P281B
-
The Keysight P281B adapter transforms waveguide transmission line into 50-ohm coaxial line. Power can transmitted in either direction, and each adapter covers the full frequency range of its waveguide band with SWR less than 1.3.
-
Product
Straight Waveguide Sections up to 110 GHz
-
Fairview Microwave’s straight waveguide sections consists of 61 models that are available in sizes ranging from WR-10 to WR-137. These waveguide straights deliver VSWR as low as 1.03:1 and are available in section lengths from 3 inches to 12 inches. They are made of either painted copper alloy or gold-plated, oxygen-free hard copper (OFHC) and feature UG, CPR and UBR-style flanges. These waveguide straight sections are ideally suited for use in industrial, defense, aerospace, test and instrumentation, medical and telecom industries.
-
-
Product
Coaxial Waveguide Adapter, 1.85 mm (m), 50 to 67 GHz
V281B
-
The Keysight V281B adapter transforms waveguide transmission line into 50-ohm coaxial line. Power can transmitted in either direction, and each adapter covers the full frequency range of its waveguide band with SWR less than 1.3.
-
Product
Double Ridged Waveguide Horn
TEMH20
-
Frequency range: 1 GHz - 22 GHz VSWR (max): < 2.6:1Impedance: 50 O (Ohm)Connector: 3.50mm female Power (CW / Peak): 20 W / 50 W
-
Product
Fixed Attenuator (Waveguide)
-
Fixed waveguide attenuator in a variety of freuqencies, power levels and attenation values.
-
Product
Waveguide Adapter
-
RF Lambda’s waveguide adapter product line is used to convert a waveguide interface to a coaxial interface. They come in a variety of frequencies, connector options and materials. They offer low insertion loss and VSWR as well as high power handling.
-
Product
E Bend Waveguide
-
E-plane waveguide bends are sections of high-precision crafted waveguides and shaped to either 30º, 45º ,60º, or 90º angles for e-plane needs. It directs the radio frequency beam and “bends” the signal to go the direction you want. Think of it like Tokyo drifting around a corner in your car. Precision MMW will help you with the highest quality E bend waveguides. We are a millimeter wave spectrum manufacturer of various active and passive mmWave products and sub-system engineering.View more E Bend Waveguide
-
Product
Mechanical Calibration Kit, 18 To 26.5 GHz, Waveguide, WR-42
K11644A
Mechanical Calibration Kit
The Keysight K11644A calibration kit contains the precision mechanical standards required to calibrate the systematic errors of Keysight network analyzers. This calibration kit has a precision airline for performing the Thru-Reflect-Line (TRL) calibration, the most accurate error-correction technique for coaxial measurements. This kit also contains a commercial calibration certificate, flush short circuit, a precision shim, and fixed termination(s).
-
Product
Waveguide Power Sensor
E8486A
Power Sensor
Keysight waveguide power sensors are fully compatible with Keysight EPM (E4418B/19B, N1913A/14A), EPM-P (E4416A/17A) and P-Series (N1911A/12A) power meters. The V8486A and W8486A are also compatible with the discontinued or obsolete power meters such as 435B, 436A, 437B, 438A, 70100A, E1416A, E4418A, and E4419A power meters.
-
Product
Millimeter Wave Frequency Counter 70-170 GHz
-
Insight Product Co. offers the electronic frequency counter for frequency measurements of millimeter wave generators of continuous or pulsed signals. The counter has an auto and waiting modes of operation and a direct 6-digits reading in frequency range (70-170) GHz without an external mixer.
-
Product
Waveguide Duplexer
-
Waveguide Duplexers supporting commercial communication to combine transmit and receive on to one antenna
-
-
Product
Waveguide Harmonic Mixer, 40 to 60 GHz
11970U
-
The Keysight 11970U waveguide mixer is a general-purpose harmonic mixer employing a dual-diode design to achieve flat frequency response and low conversion loss. These are achieved without external dc bias or tuning stubs. Manual operation and computer-controlled hardware operation are simplified because mixer bias and tuning adjustment are not required.
-
Product
Millimeter Wave Antenna Testing
-
If you are involved in antenna or system level design using mmWave or THz frequencies, then you understand the importance of dependable testing equipment. It may be that you are designing passive phase array or that you are designing a mmWave radar sensor system, but when it comes to validation of your design, simulation can only bring you so far. Phased array antennas have to be measured over the air (OTA) to ensure the radiation pattern of your design efficiently conducts energy in the right direction which is where the MilliBox comes in.
-
Product
Right Angle Waveguide to Coax Adapters
-
Fairview Microwave right angle waveguide to coax adapters include millimeter wave frequency ranges with models in the K-band (18 to 26.5 GHz) up to the V-band (50 to 65 GHz). These right angle waveguide to coax adapters offer excellent VSWR as low as 1.29:1, while also providing insertion loss performance as low as 0.3 dB. Waveguide sizes available for these new 90 degree coaxial adapter models include WR-42, WR-28, WR-22, WR-19 and WR-15. These coax to waveguide adapters in a right angle design are ideal for numerous applications requiring a transition from coaxial cable to waveguide or vice versa, including SATCOM, wireless communications, industrial, test and measurement and defense systems. Fairview’s new waveguide to coax adapter products feature a right-angle configuration, those with 2.92mm connectors use a UG-style square waveguide flange, 2.4mm and 1.85mm connector versions use a UG-style circular waveguide flange. Both male and female connector options are available in each right angle waveguide to coax adapter frequency band.
-
Product
Understanding TEM, TE, and TM Waveguide Modes
-
Energy can propagate through a medium or through what is currently believed to be a vacuum. Propagation modes vary depending upon the type of energy and the nature of the medium.Electromagnetic energy is transmitted in waves. Like sound, it may propagate equally in all directions, the wave energy radiating in concentric shells corresponding to amplitude. Or it may be directional, focused to form a tight beam.View more Understanding TEM, TE, and TM Waveguide Modes
