-
-
Product
Double Ridged Waveguide Horn
DRH67
-
Frequency range: 6 GHz - 67 GHz VSWR (max): < 1.9:1Impedance: 50 O (Ohm)Connector: 1.85mm female Power (CW / Peak): 5W / 10 W
-
Product
Double Ridged Waveguide Horn
DRH370
-
Frequency range: 370 MHz - 6 GHz VSWR (max): < 1.6:1Impedance: 50 O (Ohm)Connector: N female Power (CW / Peak): 350W / 500 W
-
Product
Coaxial Waveguide Adapter, 2.4 mm (m), 26.5 to 50 GHz
R281B
-
The Keysight R281B adapter transforms waveguide transmission line into 50-ohm coaxial line. Power can transmitted in either direction, and each adapter covers the full frequency range of its waveguide band with SWR less than 1.3.
-
Product
10 dB V-Band Waveguide Directional Coupler for Test Labs
SWD-5038531040H-15-SB
-
ModelSWD-5038531040H-15-SB is a V band, three-port waveguide directional coupler that delivers a 10 dB nominal coupling level and 30dB minimum directivity across the full waveguide band from 50to 85GHz. The three-port coupler uses a traditional multi-holeand split block design to achieve a flat coupling level, high directivity, and low insertion loss. The interfaces of the coupler are WR-15waveguides with UG-385/Uflanges. Custom coupling levels are available under different model numbers.
-
Product
K-Band Waveguide Gunn Oscillator Module
FMWGN1001
-
FMWGN1001 is a K Band Waveguide Gunn Oscillator with a Center Frequency of 24.125 GHz and a Tuning Range of +/- 1.0 GHz. The unit has a Phase Noise @ 100kHz Offset of -95 dBc/Hz typ and Frequency Stability of -0.4 MHz/°C max. The Gun Oscillator has an Output Power of 10 dBm min and Power Stability of -0.04 dB/°C max. The Waveguide Gun Oscillator uses a Bias Voltage of 5.0 Volts and a Bias Current of 200 mA and has a Waveguide Size of WR-42 with a UG-595/U Flange.
-
Product
Waveguide Harmonic Mixers (smart mixer), 50 to 75/80 GHz
M1970V
-
The Keysight M1970V 50 to 75/80 GHz waveguide harmonic mixer is an un-preselected mixer that will extend the operating frequency range of the N9030A PXA, N9020A MXA, and N9010A EXAsignal analyzers up to 80 GHz. Smart features are embedded to help you to greatly simplify your overall test setup and improve your DANL and TOI of your test system. Go smart with harmonic mixing for your millimeter-wave applications.
-
Product
Double Ridged Waveguide Horn
QRH50E
-
Frequency range: 5 GHz - 50 GHz VSWR (max): < 2.5:1Impedance: 50 O (Ohm)Connector: 2x2.40mm female Power (CW / Peak): 5W / 10 W
-
Product
Coaxial Waveguide Adapter, APC-7, 8.2 to 12.4 GHz
X281C
-
The Keysight X281C adapter transforms waveguide transmission line into 50-ohm coaxial line. Power can transmitted in either direction, and each adapter covers the full frequency range of its waveguide band with SWR less than 1.3.
-
Product
Millimeter Wave Zero Bias GaAs Schottky Diode
HSCH-9162
-
The HSCH-9162 is suitable for medium-low barrier, zero bias detector applications. The HSCH-9162 is functional through W-band (110 GHz) and can be mounted in microstrip, finline, and coplanar circuits.
-
Product
Mechanical Calibration Kit, 12.4 To 18.0 GHz, Waveguide, WR-62
P11644A
Mechanical Calibration Kit
The Keysight P11644A calibration kit contains the precision mechanical standards required to calibrate the systematic errors of Keysight network analyzers. This calibration kit has a precision airline for performing the thru-reflect-line (TRL) calibration, the most accurate error-correction technique for coaxial measurements. This kit also contains a commercial calibration certificate, flush short circuit, a precision shim, and fixed termination(s).
-
-
Product
Waveguide Circulator/Isolator
-
RF Lambda’s waveguide circulators are typically used to prevent unwanted reflections. They offer low insertion loss and high isolation and are available in a variety of frequencies and power levels.
-
-
Product
Double Ridged Waveguide Horn
DRH20E
-
Frequency range: 1.6 GHz - 20 GHz VSWR (max): < 1.5:1Impedance: 50 O (Ohm)Connector: SMA female Power (CW / Peak): 50W / 100 W
-
Product
Waveguide Switches
-
With over 70 years of RF experience, EVERAXIS specializes in designing the most demanding Waveguide Switches in extremely complex systems, including in low quantities.
-
-
Product
Waveguide Power Sensor
W8486A
Power Sensor
The W8486A waveguide power sensor measures average power over the frequency range 75 GHz to 110 GHz and power range -30 to +20 dBm.
-
Product
Waveguides
-
A waveguide attenuator is an RF device specifically designed to reduce the power of a signal without affecting or reducing the waveform of the signal.
-
Product
Coaxial Waveguide Adapter, 1.0 mm (f), 50 to 75 GHz
V281C
-
The Keysight V281C is a 1-mm female to V-band waveguide adapter with a frequency range of 50 GHz to 75 GHz. The V281C is used with the Keysight 8510XF systems.
-
Product
Double Ridged Waveguide Horn
QRH40
-
Frequency range: 4 GHz - 40 GHz VSWR (max): < 2.4:1Impedance: 50 O (Ohm)Connector: 2xK female Power (CW / Peak): 10W / 20 W
-
Product
Passive Waveguide Components
-
We cover all kinds of connections between waveguide, coaxial, micro-strip and co-planar lines. Filters are available in waveguide technology as well as in stripline/micro-strip. Passive structures such as power splitter, power combiner, ortho-mode transducer and hybrids mostly are designed to meet the specific goals of the customer.
-
Product
Double Ridged Waveguide Horn
DRH30
-
Frequency range: 2.5GHz - 30 GHz VSWR (max): < 1.55:1Impedance: 50 O (Ohm)Connector: K female Power (CW / Peak): 25W / 50 W
-
Product
Double Ridged Waveguide Horn
DRH200
-
Frequency Range 200 MHz 2.2 GHz VSWR (AVG) < 1.4:1Impedance 50 WConnector N femalePower (CW / Peak): 500 W / 1000 W
-
Product
Coaxial Waveguide Adapter, 3.5 mm (f), 18 to 26.5 GHz
K281C
-
The Keysight K281C adapter transforms waveguide transmission line into 50-ohm coaxial line. Power can be transmitted in either direction, and each adapter covers the full frequency range of its waveguide band with SWR less than 1.07.
-
Product
Coaxial Waveguide Adapter, 1.0 mm (f), 75 to 110 GHz
W281C
-
The Keysight W281C is a 1-mm female to W-band waveguide adapter with a frequency range of 75 GHz to 110 GHz. The Keysight W281C is used with the Keysight 8510XF systems.
-
Product
Waveguide and Coaxial Rotary Joint Assembly
-
Waveguide and Coaxial Rotary Joints are used for the transmission of power and signal between the locked and rotating parts of a radar or satcom system.
-
Product
In-Line Coaxial-to-Waveguide Adapter, 1.0 Mm (m) To WR-12, 60 To 90 GHz
E281DS
-
E281DS In-line 1.0 mm (m) - to- WR-12 waveguide adapter offers a simple way of measuring waveguide devices in E-band, 60 GHz to 90 GHz.
-
Product
Coaxial Waveguide Adapter, 2.4 mm (f), 33 to 50 GHz
Q281A
-
The Keysight Q281A is a 2.4 mm female to WR-22 waveguide adapter that operates in the 33 to 50 GHz frequency range. These adapters transform waveguide transmission lines into 50 ohm coaxial lines. Power can transmitted in either direction, and each adapter covers the full frequency range of its waveguide band with SWR less than 1.3.
-
Product
RF Waveguide Load
-
RF Lambda’s waveguide loads are used at end of an RF signal chain to provide a good 50ohm match and dissipate any RF energy into heat. They are available in a variety of power levels and offer low VSWR.
