PXI Systems Alliance
promotes and maintains the PXI standard.
-
Product
Semi-Automatic LCD Probe Station/Laser Repair System
LCD 2424
-
The Model 2424 Semi-Automatic LCD Probe Station is designed especially for probing LCDs and other large substrates. Built on a steady and reliable anti-vibration table, the Model 2424 has powerfully built features that perform a number of specific tests required by all LCD/flat panel display manufacturers.
-
Product
PXI Prototyping Module, 2-Slot no Connector
40-225A-002
Prototyping Module
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
Product
UDT-Series Integrating Sphere Systems
-
Gamma Scientific offers a variety of pre-configured integrating sphere systems for use in conjunction with the UDT line of optical meters, with both 25 mm and 150 mm diameters.
-
Product
Humidification Systems
-
The Humidity bottles are made from type 316 stainless steel. Swagelok fittings for gas inputs and outputs are welded into the bottle. Nafion tubing inserted into a type 316 stainless steel spring for support is coiled in the bottle to provide dew-point humidity level for the gas passing through the tubing. The bottle is insulated and heated using a silicone rubber flex-pad.
-
-
Product
PXI Resistor Module 2-Channel 1.5R to 4.09k
40-293-023
Programmable Resistor Module
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Barcode Verification Systems
REA ScanCheck 3
-
The REA ScanCheck 3 is an universal, battery-operated, high-performance barcode verification device which operates in accordance with current standards. The verifications document compliance with quality goals in production and monitoring of barcodes on data storage devices and products of all kinds. The measurement principle is based on a laser scanner optimized for verifications. This makes contact-free measurement, largely independent of handling influences, possible. For mobile use on site, the device operates self-sufficiently, independent of the power network with standard, rechargeable batteries. The operating system and application software support multiple languages.
-
Product
Review System
RV-3000
-
Reduces surface inspection device review time and contributes to greater inspection efficiency! This system uses address information for defects detected by surface inspection equipment to acquire images of defects with a high level of magnification, and categorizes defect types.
-
Product
TTEDevelopment System Space
-
The TTEDevelopment System Space provides a full development environment for hard real-time and non-real-time Ethernet communication on the same network using different quality of service traffic classes. Standard Ethernet traffic seamlessly integrates with fully deterministic, synchronous hard real-time Ethernet traffic on the same physical media. The system allows the evaluation and development of real-time applications leveraging the benefits of TTEthernet products in an out-of-the-box system.
-
Product
SPM Control System
Nanonis
-
SPECS Surface Nano Analysis GmbH
Unbound to any specific microscope, the Nanonis SPM Control System is designed for the uncompromising demands of scientific excellence in a wide variety of SPM applications. Its modular concept implemented in a fully digital fashion is carefully thought through, with a strong emphasis on usability, stability and flexibility.
-
Product
Fiber Optic Test System
OPTOWERE-S100 (Fiber Optic Test System)
-
The frame of FOTS system consists of the Main control part and the Slot mounting part. The Main control part is in charge of control and interface of the system and the Slot mounting part can hold up to maximum 8 slots, which are modularized according to each function and come out in five kinds. This integrated test system is designed to help manage the test and measurement related to optical communication and component. And the modular architecture of FOTS allows for customized configuration so that the slot of LD Driver, 2 channel VOA, 1 X 4 switch, WDM EDFA and C + L – Band ASE Source can be chosen according to user’s necessities. Main control part and each function module are run by effective and multi-functioned system control program in the base of high speed remote interface, GUI display and the discriminative high speed driving of module and system. This system can provide variety manufacturing and laboratory applications such as general quality test and reliability test of optical component and optical signal transmission test through efficient linkage with other system.
-
Product
Goniophotometer Test System For Led Lamp
1680A 1680B
-
Shenzhen Chuangxin Instruments Co., Ltd.
Design according to IEC61341,the test method of central luminous intensity and beam angle for reflecting light, this instrument can be used to test the cross section luminous intensity distribution curve, central luminous intensity and effective beam angle of LED assembled luminaries and LED lens system with diameter less than 180mm.
-
Product
Ionic Contamination Test Systems
CM+ Series
-
The Contaminometer (CM+ Series) system was originally developed by Protonique, the business of industry guru Brian Ellis. They also featured in the early development programmes of "cleanliness measurement" carried out by the US Department of Defense at China Lake in the 1970s. Historically, International Standard IPC-J-STD001 stated that assemblies be cleaned to a value of <1.5µg/cm2 of NaCl equivalence. However, the new design is linked to the introduction of the new process control metric introduced by Gen3 Systems: Process Ionic Contamination Testing. The CM+ Series measure the amount of ionic contamination in accordance with all existing test methods, often referred to as ROSE testing, as well as the new PICT test.
-
Product
High Power Probe System Solutions
-
MPI Advanced Semiconductor Test
MPI high power probing solutions offer variety of probing systems which include manual, automated and fully-automated versions to provide solution for different budgets and specific requirements.
-
Product
ECM Noise Under RF Test System
BK8020
-
The BaKo Type BK8020 ECM Noise Under RF Test System tests microphones under RF noise, using a ‘Direct Injection Test’ in the frequency range of 5MHz~2.5GHz with an amplitude modulated (AM) disturbance signal of 1kHz. You run the system using the controlling PC, which allows automatic configuration and which runs the test sequence automatically. When you finish testing, you can print data as an MS Excel report or save it for comparison and analysis.
-
Product
System Extensions
-
Teach your scanner to 'see' – for greater accuracy and flexibility – and to 'fly' – for increased efficiency and productivity. Extend the lifespan of your scanning system with process-specific equipment.
-
Product
Multi-Cell Test System
Cellcia
-
Next-generation wafer probing system for 300mm wafers. The multi-layer system structure maximizes the efficiency of testing, further reducing the total testing cost.
-
Product
PXI Power Multiplexer, 16-Channel, 2 Pole
40-650A-002
Multiplexer Module
The 40-650A-002 is a PXI 16 Channel Power Multiplexer, suitable for switching inductive/ capacitive loads up to 5A at 250VAC.
-
Product
Emission Monitoring Systems
-
Gasmet’s emission monitoring systems set the standard for accurate, reliable, and cost-effective gas analysis. Our state-of-the-art solutions are designed to provide precise measurements of gaseous emissions, making compliance with environmental regulations seamless. With a focus on continuous emission monitoring systems (CEMS), we deliver innovative technology that balances sensitivity, durability, and affordability. Our products are fully TÜV and MCERTS-certified, ensuring world-class quality and performance. Trusted globally, our emission monitoring solutions are the future of gas analysis, empowering industries to meet stricter environmental requirements effortlessly.
-
Product
AXIMA Microorganism Identification System
-
The AXIMA Microorganism Identification System presents a new solution for the identification of microorganisms for microorganism research in the pharmaceutical, food, science, energy, environment, clinical and health fields.
-
Product
CPCI Or PXI PCM & ARINC 717 Board
MS 1703
-
*Bus Interface - PXI / CPCI Bus*Microprocessor and FPGA design based Board*One Channel ARINC 717 Transmitter and Receiver*Generates all PCM telemetry signals like NRZ, Bi-Phase, Differential Bi-phase, DM signals*Used to test all types of PCM based telemetry equipments*Configurable output signals format (parity, word length, Minor, Major frame, Bit position)*User can configure the words and there positions in the frame*The word can be either a square / triangle wave data or constant data*1 MB Shared Memory for Data Storage*Driver interface for Windows2000/XP/VISTA and LINUX OS
-
Product
PXI 10xSPST 16A Power EMR Module
40-161-003
Relay
These Power Relay Modules are intended for switching heavy AC or DC loads or for the slave switching of large external relays, contactors and solenoids. The 40-161 is ideal for switching up to 16A in both AC and DC applications.
-
Product
Analog Output PXI Card
GX1642
Analog Output Module
The GX1642 is a 3U PXI digital to analog output board is designed specifically for applications where multiple analog outputs are required. The GX1642 offers precision signal sourcing performance and quality at an economical price.
-
Product
Wafer and Cells PL System
HS-PL
-
Photoluminescence (PL) Imaging is a unique non-invasive inspection tool as it can be used in-line at many different steps of the cell manufacturing process. This facilitates the direct comparison of data obtained at one process step to data obtained at another. Additionally, PL imaging can be compared to electroluminescence (EL) imaging on finished cells using comparable equipment.
-
Product
Universal ARINC HSI Test System
TA-1000
-
This is our ARINC Standard Universal HSI Tester designed to provide a full range of capabilities that allow testing most any HSI you will see come through your shop.
-
Product
On-board Emissions Measurement System for NH3/N2O
OBS-ONE IRLAM Unit
-
The OBS-ONE IRLAM unit is an on-board emissions measurement system for analyzing the NH3/N2O under real-world driving conditions and supports our customer’s future regulatory development.The IRLAM unit combines with the GAS unit and the PN unit to measure the specified exhaust gas components, along with the exhaust gas flow rate, the GPS position, and the atmospheric conditions (temperature, humidity, pressure).
-
Product
X-ray Inspection System
X-eye SF160 Series
-
High-performance Micro-focus Open Tube with 160kV is installed and fine defects of 1㎛ are detectable. High-resolution X-ray image can be gained with world best magnification by installing high-price Open Tube as standard.Dual CT function can be purchased adtionally, and exact location & size of defects can be detected and analyzed with this function.
-
Product
ThermalAir Series Temperature Forcing System
ThermalAir TA-1000B Rack Mount Test System
-
The ThermalAir TA-1000B high capacity thermal air stream system is used for temperature testing, fast thermal cycling, and device temperature characterization of components, hybrids, modules, PCBs, and other electronic and non-electronic assemblies at precise temperature from -25°C to +200°C.
-
Product
Liquid Auto Refill System
LU Series
-
The LU Series offers uninterrupted, safe and reliable delivery of the liquid precursor to liquid material baking systems and injection systems. This leads to increased uptime, reduced operator handling and reduced risk of process contamination.The LU Series includes a function for automatically implementing a remaining liquid purge sequence.Using the LU Series, product throughput and maintenance efficiency is improved.
-
Product
Industrial System
-
Axiomtek has a full range of fanless, industrial PCs that are suitable for different environments and applications. These industrial PCs deliver powerful computing performance, expansibility, high storage capacity, reliability, solid design, and cost-effectiveness. Axiomtek’s IPC products offer CE marking, popular interfaces and rich I/O options.
