I²C
A slow Inter-Integrated Circuit bus protocol.
-
Product
I-7188 C Language Embedded Controllers
-
ICP DAS offers an entry line of I-7188 controllers, programmable in C language, and offering a user friendly ROM-DOS based operating environment. The I-7188 line offers a simple entry level platform to implement basic embedded control and logic, while maintaining a modular architecture for implementation in to a multitude of industrial applications!
-
Product
I²C/SPI Interface Device
Interface
The I²C/SPI Interface Device is a master or slave interface for inter-integrated circuit (I²C), or master interface for serial parallel interface (SPI) devices. With plug-and-play USB connectivity, the I²C/SPI Interface Device is a portable solution to communicate with consumer electronics and integrated circuits. The I²C/SPI Interface Device can be physically located more closely to I²C/SPI devices than PCI interfaces, reducing I²C bus length and minimizing noise problems. The I²C/SPI Interface Device supports I²C rates up to 250 kHz and SPI rates up to 50 MHz, and it also includes eight general-purpose digital I/O lines for a variety of applications, such as configuring the address of I²C devices or toggling LEDs.
-
Product
32 Form C High Power Relay Module
DP-cPCI-4035
-
DP-cPCI-4035 is a cPCI-based 32-channel high power relay. It is designed as general-purpose module. Applications of this module include power routing, relay outputs for soft PLCs, automatic test equipment, hardware simulation and high current measurement routing.
-
Product
Fully-Automatic Kjeldahl Analyzer
LD-LKA-C10
-
Fully-automatic Kjeldahl AnalyzerLD-LKA-C10conducts titration and distillation simultaneously so as to neutralize the ammonia gas released which enhance the test efficiency and avoid the overflow of ammonia. It stand with a measuring range from 0.1 to 200 mgN which gives a maximum recovery of ≥ 99.5 %. The operating ambient temperature of the device starts from 10 °C to 35 °C. 8.0-inch LCD touch screen is used to set the distillation time, the amount of diluent, acid liquor and alkali. Diaphragm pump is used to add reagent so that the injure caused by high pressure pump can be neglected. Wireless network modules is installed for realizing remote data transmission to test data processing and report printing.
-
Product
Industrial Gateway
AFE-E630
-
Advantech AFE-E630 is an industrial gateway powered by the Rockchip RK3568J, designed for I&C ESS energy storage management.
-
Product
Basic Contact Probes (100 Mil) F10006B130G100
1017399
-
The Basic Contact Probes (100 mil) F10006B130G100, identified by order code 1017399, represent a reliable solution for various connectivity needs. These probes are engineered to operate efficiently across a temperature range from -45°C to +80°C, offering versatility in extreme conditions. The design features a 2.54 mm pitch, enabling precise placements in tightly packed electronic assemblies. With a robust construction that includes a beryllium copper plunger and a bronze barrel plated with gold, these probes ensure reliable electrical connections with minimal contact resistance of 20 mOhm and a continuous current rating of 5A, making them suitable for high-performance applications.
-
Product
Anemometer, 0.8m/s to 30m/s, 0 °C, 50 °C, 80%, 180 mm
72-6638
-
An instrument to accurately measure air velocity and wind speed in air conditioning and heating systems as well as for environmental monitoring.
-
Product
Basic Threaded Probe F73217B140G300
1009852
-
The F73217B140G300 Basic Threaded Probe is engineered for precision and reliability, making it an essential choice for various applications. The probe boasts a basic contact design suitable for a range of F-series models, including F722, F724, F732, and F727. Operating efficiently across a temperature range of -45°C to +100°C, this probe is crafted to meet demanding performance standards. With a pitch of 2.54 mm, it ensures meticulous spacing and accurate measurements, bolstered by its ability to handle continuous currents of up to 5 A while maintaining a typical contact resistance of just 25 mOhm.
-
Product
EN 50155 M12 8FE Managed Switch
EKI-9508E-MW
-
M12 connector with IP67 rugged housing, Complies with EN50155 & EN50121-3-2, Complies with EN45545-2 & EN61373, Wide nominal power input range: 24~110VDC; Operating power input range: 16.8~137.5VDC. Compact size to fit in different narrow spaces, Operating temperature: -40 ~ 70°C.
-
Product
New Generation Memory Expansion
SQR-CX5N
-
New Generation Memory Expansion_CXL 2.0 E3.S 2T DDR5. EDSFF E3.S 2T form-factor, Data Transfer Rate: PCIe Gen 5.0x8 32GT/s. Capacity : 64GB Operating Temperature: 0°C ~ 70°C.
-
Product
Basic Threaded Probes (F723, F733, F734, F735, F737) F73716B180G300
1010679
-
The Basic Threaded Probes, particularly model F737, epitomize precision and reliability for a variety of applications. Designed primarily as a Basic Contact Probe, it excels under extreme temperature conditions, withstanding temperatures from -45°C to +100°C. The F737 probe is engineered for high performance, featuring a pitch of 4.00 mm (or 157 mil), making it suitable for efficient interaction in low-profile spaces while ensuring optimal electrical conductivity due to its robust design and material selection.
-
Product
Sensor Six-Pack
PT-6
-
PT-6 Sensor Six-Pack - For multi-point temperature measurements. Inexpensive, Flexible. Welded sensor beads, tough kapton insulation. Diameter is .029''. Maximum temperature 350°C, Time constant 0.01 Seconds. 5 foot lead. Not isolated.
-
Product
Step Probe F73316B0064G300SP
1000971
-
The F73316B0064G300SP Step Probe represents the pinnacle of precision engineering, specifically designed for applications requiring meticulous measurements in testing environments. With a pitch of 4.00 mm and capable of operating under extreme temperatures ranging from -45°C to +100°C, this probe is perfect for diverse industrial applications. It ensures reliable performance with a continuous current rating of 10.00 A and a typical contact resistance as low as 25.00 mOhm, making it a valuable tool for engineers and technicians alike.
-
Product
Basic Contact Probes (100 Mil) F77206B200G300H
1001625
-
The Basic Contact Probes (100 mil) F77206B200G300H (Order code 1001625) are designed with precision engineering to meet a variety of electrical and mechanical specifications. These probes boast a continuity current rating of 5.00 A and a typical contact resistance of just 100 mOhm, ensuring reliable performance in demanding environments. Capable of operating at temperatures ranging from -45°C to +100°C, these probes are well-suited for both extreme conditions and standard applications. With a total length of 32 mm and a maximum travel distance of 5 mm, they offer exceptional flexibility in connectivity applications.
-
Product
Pulse Generator
Digital Ring Kits
-
NEMA C frame rings provide mounting for 1101, 1201, and 1202 shaft speed sensors for use with 199SM magnet wheels on motors with NEMA C frames. The DRK (Digital Ring Kit) Series provides a single-channel output and the QDRK (Quadrature Digital Ring Kit) Series offers a bi-directional output. Kits include mounting ring, hardware, magnet wheel, and sensor.
-
Product
Basic Contact Probes (50 Mil) F05038S050L150
1010393
-
The Basic Contact Probes, specifically the model F05038S050L150, are engineered for exceptional performance with a design that incorporates advanced technical specifications. These probes exhibit a pitch of 1.27 mm (50 mil) and can operate within a temperature range of -45°C to +80°C, making them suitable for various demanding applications. Built for reliability, they handle continuous currents of up to 3.00 A while ensuring a low typical contact resistance of just 20 mOhms. This combination of durability and precision makes them ideal for extensive test and measurement scenarios.
-
Product
sbRIO-9215, Non-Enclosed, ±10 V, 100 kS/s/ch, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Modul
780878-01
Voltage Input Module
Non-Enclosed, ±10 V, 100 kS/s/ch, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module - The sbRIO‑9215 performs differential analog input. The sbRIO‑9215 contains NIST‑traceable calibration, a channel‑to‑earth ground double isolation barrier for safety and noise immunity, and high common-mode voltage range. Non-enclosed modules are designed for OEM applications.
-
Product
Digital Stick Probe Thermometer
TP101
-
A multi-purpose thermometer for your laboratory, workbench, kitchen, or office. Simple to use and provides a clear digital readout in °C or °F. a sharp and sensitive metal probe, and a protective plastic sheath
-
Product
High-Frequency Ultrasonic Imaging System
USPC 3060 UHF
-
Ingenieurbüro Dr. Hillger Ultrasonic-Techniques
The ultrasonic imaging system USPC 3060 UHF is optimized for the testing wih high frequencies and delivers high resolution B-, C-, Dand F- scans. It consists of a scanning system with water tank and the external pulser-/receiver module as well as a 19”-rack with scanner controller and the ultrasonic system and monitor, keyboard and mouse.
-
Product
Switch Probes (Normally Open (NO)) F88606B300G200SM
1009241
-
The Switch Probes (Normally Open) F88606B300G200SM are designed to offer reliable performance in a variety of electronic applications. With a family designation of F886-NO, these probes feature a fundamental pitch of just 3.50 mm, ensuring compatibility with tightly spaced circuit layouts. They demonstrate a wide temperature tolerance of -45°C to +100°C, making them versatile for use in both cold and hot environments. The probes are engineered for efficient electrical performance, capable of handling continuous current up to 10 A with a typical contact resistance of only 50 mOhm, ensuring minimal energy loss during operation.
-
Product
Laser Distance Meter
KM 973
-
Kusam Electrical Industries Limited
• Measuring Range : 0.05 to 40M (KM 973) , 0.05 to 70M (KM 975), 0.05 to 100M (KM 976) • Measuring Accuracy : ± 2 mm• Display Accuracy : 1 mm• Laser Classification : Class 2M II• Laser Type : 620-690nm, <1mW• Protection against splashes and dust : IP 54• Temperature range for Operation : 0°C to +40°C• Temperature range for Storage : -20°C to +70°C• Laser Switch-OFF Automatically : After 30 Seconds• Instrument Switch-OFF Automatically : After 3 Minutes• Area, Volume Measuring.• Indirect (Pythagoras) Measurement.• Plus-Minus Method.• Continuous Measurement.• Minimum / Maximum Measurement.• Display illumination.• Show beep.• Battery Life : 5000 to 8000 Measurements• Battery Selection : Lr6 (AA) 2 x 1.5V• Dimensions : 121(L) x 56(W) x 28(H) mm• Weight : 150g
-
Product
Basic Contact Probes (50 Mil) F05043S050L150
1010865
-
The Basic Contact Probes (50 mil) F05043S050L150 are specialized components designed for precise electrical connections in demanding applications. With a pitch of 1.27mm (50 mil) and a temperature range of -45°C to +80°C, these probes are engineered to function effectively in various environments. The F05043S050L150 delivers reliability through its optimal electrical specifications, featuring a continuous current of 3.00A and a low typical contact resistance of just 20.00 mOhm, ensuring minimal energy loss and efficient operation.
-
Product
Temperature Cycling
-
Reltech provides a full capability for Temperature Cycle testing as part its full turn-key solution to package level qualification testing. Our Temperature Cycling system type Espec TSA11-A, two zone (-65°C to +200°C) vertical movement system, provides an exceptional recovery time of less than 5 minutes without the need for any auxiliary cooling.
-
Product
Basic Contact Probe F07555B150G200
1172582
-
The Basic Contact Probe, model F07555B150G200, offers a versatile and precise solution for various applications requiring accurate measurement and connection. Built to withstand substantial environmental conditions, this probe operates efficiently within a temperature range of -45°C to +80°C, making it suitable for harsh environments. The design incorporates a basic contact probe structure made from high-quality materials, ensuring reliability and durability over extended use.
-
Product
Monitoring and Control System for Elevators and Escalators
-
The software package developed in the MS Visual C ++ environment has an attractive and an intuitive graphical interface. It provides for work with several groups of equipment controllers, provides advanced analysis and control capabilities (building equipment management, passenger traffic analysis, recording and playback of diagnostic information).
-
Product
F88617T500N350SM
1000534
-
The F88617T500N350SM Switch Probe is designed for high-performance applications where precision and reliability are crucial. This normally open (NO) probe not only ensures continuous operation but also features a robust design optimized for various environmental conditions with a temperature range from -45°C to +100°C. With a basic contact structure, it delivers efficient operation with a continuous current rating of 10 A, and a typical contact resistance of just 50 mOhm, making it an excellent choice for modern electronic applications where low resistance is key.
-
Product
Basic Contact Probe F73212B180G150
1003184
-
The Basic Contact Probe F73212B180G150, with order code 1003184, is engineered for precision and reliability in various applications. This probe features a robust design with a pitch of 2.54 mm and a temperature tolerance ranging from -45°C to +100°C, making it ideal for challenging environments. Whether in a testing or measuring capacity, its specifications ensure consistent performance under standard operational conditions.
-
Product
Infrared Thermometers
-
Easily measure surface temperatures with ThermoWorks non-contact IR guns, ideal for produce and agriculture inspectors, HVAC, construction, warehouse, quality assurance, HACCP and cold chain management, both shipping and receiving. Choose from fixed or adjustable emissivity; single, dual or circle laser types; and lens optics from close focus—for electronic components and laboratory measurements—to 100:1—for long distance measurements. High temperature ranges up to 3272°F (1800°C) are perfect for metallurgy and metal work foundries.
-
Product
Basic Contact Probes (100 Mil) F10037S050L300
1007223
-
The Basic Contact Probes (100 mil) F10037S050L300, with order code 1007223, are precision instruments designed for high-performance applications. Engineered to operate within a temperature range of -45°C to +80°C, these probes deliver reliable performance in various environments. With a continuous current capacity of 5.00 A and a typical contact resistance of only 20 mOhm, they ensure efficient signal integrity for electrical testing and measurements.
-
Product
Step Probes F73216B0075G300SP
1000991
-
The Step Probes F73216B0075G300SP (Order code: 1000991) is designed for precision applications requiring robust mechanical and electrical specifications. Boasting a pitch of 2.54 mm (100 mil), it performs optimally across a temperature range of -45°C to +100°C, ensuring reliability in various environments. This probe integrates seamlessly into advanced testing applications, offering features like a nominal travel of 4 mm and a maximum travel of 5 mm, making it incredibly versatile for intricate tasks where precision is paramount.
