I²C
A slow Inter-Integrated Circuit bus protocol.
-
Product
Practical Use Precision Type Comparison Blackbody Furnaces
IR-R6, IR-R7, IR-R8
-
Practical use precision type comparison blackbody furnaces cover the temperature range of 100 to 3000°C by 3 kinds of blackbody furnace and calibrate radiation thermometers accurately.
-
Product
Automatic testing with National Instruments TestStand
-
TestStand from National Instruments is standard software for automated testing. Complex, variable test systems can be built here by integrating various hardware and software modules (e.g. LabVIEW VIs, C # modules). We can easily integrate created LabVIEW VIs into TestStand for a product-specific test sequence. All functions that are required for an automatic test sequence are available. Parameters can be changed in the TestStand environment. The user interface can be adapted to your needs.
-
Product
NI-9149, 8-Slot, Zynq-7020 FPGA, Ethernet CompactRIO Chassis
783376-02
Chassis
8-Slot, Zynq-7020 FPGA, Ethernet CompactRIO Chassis - The NI‑9149 is a rugged Ethernet chassis that you can use to add C Series I/O modules to any standard Ethernet network. You can program the chassis using Scan Mode for fast expansion of your real-time system or using the onboard FPGA for inline processing and high-speed I/O and control. With the NI‑9149, you can add high-performance I/O to your PC-based application or expand your CompactRIO, PXI, or industrial controller application.
-
Product
Endevco Cryogenic Charge Output Accelerometers
-
PCB's acquisition of Endevco's full line of testing sensors means all Endevco sensors are now backed by PCB's Total Customer Satisfaction (TCS) guarantee. Endevco® cryogenic piezoelectric accelerometers are built specifically for measuring vibration under cryogenic conditions down to -452° F (-269° C). Signal outputs of these units are very stable even at extremely low temperatures. Their rugged internal construction is designed to withstand multiple cycles of thermal shock with steep temperature gradient. The accelerometers are self-generating devices that require no external power source for operation and contain no electronics. This allows them to operate below the -320° F (-196° C) limit of ICP accelerometers, down to -452° F (-269° C).
-
Product
CO2 Concentration Transmitter
T5440
-
The transmitters are designed for online measurement of temperature (C or F), relative humidity and carbon dioxide concentration of air without aggressive ingredients. Measured temperature and relative humidity are recomputed to following humidity expression: dew point temperature, absolute humidity, specific humidity, mixing ratio and specific enthalpy.
-
Product
Airborne Receivers & Bit Synchronizers
-
The Lumistar LS-28-DRSM Series Multi-Mode Multi-Band Receiver/Combiner/TM Processing Unit is designed using ruggedized packaging to survive severe airborne conditions. The LS-28-DRSM is available in several configurations: 1) Airborne receiver only (RF to bits), 2) Airborne bit synchronizer only, 3) RF to TM Processing and Display (RF to bits to UDP decom to LAN Client Displays). Models with receivers are available in any band form 200 MHz to 7 GHz with S, lower L and C bands as standards. Other RF bands are available, please consult the factory for details. This unit can be mated with other Lumistar products to provide a complete air-to-ground re-transmission system.
-
Product
FieldFox C Handheld Microwave Analyzer, 6.5 GHz
N9914C
-
Capture elusive signals with up to 120 MHz gap-free, real-time bandwidth. Capture elusive signals with up to 120 MHz gap-free, real-time bandwidth. Measure all four S-parameters simultaneously with 115 dB dynamic range. Make accurate spectrum analyzer measurements (± 0.3 dB) without warmup. Perform over-the-air measurements for 5G NR and LTE. Use GPS/GNSS for geolocation and timestamping.
-
Product
Thermometer REPLACED BY PTM-1
BA T-7001H
-
In applications where clinical accuracy is not mandatory and cost is a consideration , the BAT-7001H is Physitemp‘s most compact, low cost thermocouple thermometer. The Model BAT-7001H is a high performance, precision hand-held instrument for the measurement of temperature using Type T (copper-constantan) thermocouples. This versatile instrument measures temperature in both °C and °F. The internal memory of the micro-computer stores the minimum and maximum measured temperature for instant recall via the LCD display. BAT-7001H operates on a 9V battery.
-
Product
NI-9207, 500 S/s, 16-Channel C Series Voltage and Current Input Module
781068-02
Current Input Module
500 S/s, 16-Channel C Series Voltage and Current Input Module - The NI‑9207 is a combination voltage and current input module designed with industrial systems in mind. It features eight current and eight voltage input channels, with built-in noise rejection.
-
Product
PMC Module
PMC-1553
PMC Module
Operating temperatureCommercial: 0 to +55 °COptional: -25°C to +80°C• Non-operating: -40°C to 85 °C• Airflow requirement: .5 CFM• Humidity: 5 to 90% (non-cond.)• Altitude: 0 to 10’000 ft
-
Product
Pocket Sized Celsius Scale Dial Thermometer w/ 5 Inch Stem
TC70
-
UEi Test & Measurement Instruments
Celsius scale thermometer with a 1 inch dial and a 5 inch stem with a -40˚ to 70˚C range
-
Product
Vibrating Sample Magnetometer
VSM-P2H
-
This is low magnetic field type of exclusive use for soft thin film sample by the use of Helmholtz Coil.The type is capable of measuring variations of temperature from -50°C to 200°C by adding gas-flow type of temperature controller as an option.
-
Product
PXIe-8234, 2-Port Gigabit PXI Ethernet Interface Module
780244-01
Ethernet Interface
Vision Software Included, 2-Port Gigabit PXI Ethernet Interface Module—The PXIe-8234 with Vision Acquisition Software can acquire images from the fastest GigE Vision cameras. It transfers images at full Gigabit Ethernet bandwidth on both ports simultaneously, and it is optimized for extremely low CPU load. The PXIe-8234 with Vision Acquisition Software provides full GigE Vision bandwidth at every port, giving you the bandwidth you need for your most demanding vision applications. It also includes NI Vision Acquisition Software, which is driver software for acquiring, displaying, logging, and monitoring images from a multitude of camera types. With a set of easy-to-use functions and example programs, you can quickly create applications using LabVIEW, C, C++, C#, Visual Basic, and Visual Basic .NET.
-
Product
Cable Assembly, 50-Pin D-Type, Female to Unterminated With Cut Ends, 1m HV, Exit Away From Pin 1
A050DF4-C-HA100
Cable Assembly
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
Probe Temperature Meter
-
Kusam Electrical Industries Limited
• Measurement Range : -50°C ~ 270°C; -58°F ~ 518°F• Resolution : 0.1°C (-50°C ~ 200°C) ; 1°C (200°C ~ 270°C)• Accuracy : -50°C ~ -20°C : ± (reading x 1.5% + 1°C), -20°C ~ 200°C : ± (reading x 1.0% + 1°C), 200°C ~ 270°C : ± (reading x 2.0% + 4°C)• Auto Power Off : 8min• Low Battery indication• °C / °F display selection
-
Product
Standard & Custom Test Fixtures
-
Both standard and custom Test Fixtures from OAI enable the user to integrate the solar cell with the I -V tester. Fixture configurations range from from simple hold down devices to temperature-controlled fixtures with front and back side contact. We invite you to contact an OAI Application Engineer for help with your fixture design. With our expert guidance, you can expect maximum performance from your I -V Tester and Solar Simulator.
-
Product
Low PIM Cable Assemblies
-
Low-PIM jumper cables feature a maximum PIM level of -155 dBc and are made with UL910 plenum-rated SPP-250-LLPL cable. The PIM levels of each cable have been fully tested with the results of those tests marked on each cable. These Low-PIM cables boast a maximum operating frequency of 6 GHz and a maximum VSWR of 1.25:1 up to 2 GHz and 1.35:1 up to 6 GHz. These Low-PIM cables are lightweight, flexible and have an operating temperature range of -55°C to +125°C and are available with 4.3-10, 7/16 DIN, N and 4.1-9.5 mini-DIN connector combinations, including right-angle connectors.
-
Product
Rotating Warning Light
ND-AM1
-
-Red rotating light on stand with 25 foot power cable.-Operating Temperature: -20 to 50 °C (-4 to 122 °F), Humidity: Non-Condensing 95%
-
Product
Gauge Type T Thermocouple Wire
W-TW-40
-
Most thermocouple wire used in the manufacture of sensors is "Special Limits" wire which, to meet NIST standards, must be accurate to 0.5°C in the range 0-50°C. This means that even with most sophisticated electronics, the best possible accuracy for the system is 0.5°C.
-
Product
Alternate 2.82 (80.00) - 5.00 (141.00) General Purpose Probe
HPA-74T75-1
General Purpose Probe
Current Rating (Amps): 3Average Probe Resistance (mOhm): 35Test Center (mil): 100Test Center (mm): 2.54Test Center Remark: max. test center 187 mil / 4,74 mmFull Travel (mil): 100Full Travel (mm): 2.54Recommended Travel (mil): 75Recommended Travel (mm): 1.91Mechanical Life (no of cyles): 2,000,000Overall Length (mil): 598Overall Length (mm): 15.19Overall Length Remark: Tip “A-B”: 598 (mil), 15.19 (mil), Tip “C”: 586 (mil), 14.88 (mil), Tip “E, T135, T156, T65, T80”: 610 (mil), 15.49 (mil), Tip “T75”: 620 (mil), 15.75 (mil)
-
Product
NI-9426, 24 V, 32 Channel (Sourcing Input), 7 µs C Series Digital Module
780030-01
Digital Module
24 V, 32 Channel (Sourcing Input), 7 µs C Series Digital Module - The NI‑9426 works with industrial logic levels and signals to connect directly to a wide array of industrial switches, transducers, and devices. Each digital input line is compatible with 24 V logic levels.
-
Product
Cable Assembly, 50-Pin D-Type, Male to Unterminated With Cut Ends, 2m HV, Exit Away From Pin 1
A050DM4-C-HA200
Cable Assembly
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
UV Fluorescence Hydrogen Sulfide Analyzer
Model T101
-
The Model T101 H2S analyzer uses the proven UV fluorescence principle to measure hydrogen sulfide at levels commonly required for ambient air monitoring.The Model T101 is equipped with an internally mounted catalytic converter set at 315°C to convert H2S to SO2. A switching mode alternately measures H2S and SO2 while showing both readings concurrently on the front display.All T Series instruments offer an advanced color display, capacitive touch screen, intuitive user interface, flexible I/O, and built-in data acquisition capability. All instrument set up, control and access to stored data and diagnostic information is available through the front panel, or via RS232, Ethernet, or USB com ports, either locally or by remote connection.The Model T101 comes with NumaView™ Software. NumaView™ Remote PC Software allows for a remote connection with virtual interface and data downloading capability to analyzers operating NumaView™ Software.
-
Product
HS-1760 Flight Rated XMC Network Interface Controller
XMC-1760-NIC-CC
-
Avionics Interface Technologies
Dual Channel configurations supporting NC/NC, NC/NT, or NT/NT - 75 Ohm single ended copper or 150 Ohm differential - Eight (8) opto-isolated discrete I/O lines - Rear I/O through the P16 connector - Conduction-cooling and/or conformal coating available - x4 PCIe interface to NIC interfaces, with DMA controller for data movement - Designed for extended temperature operations - ANSI Application interface supporting C development - Device driver support: Windows, Linux, & VxWorks (others on request)
-
Product
2U 19” Edge Server with Intel® Xeon® Scalable Silver/Gold Processors for 5G MEC Infrastructure Deployment
MECS-7210
MEC Server
The MECS-7210 Edge Server focuses on the edge of 5G networks to provide an open, white box platform for 5G Open RAN, private 5G networks, and a wide range of 5G MEC applications including smart cities, retail, manufacturing, autonomous vehicles, Argument Reality(AR), virtual reality(VR) and healthcare. As one of the first NGC-Ready validated and OTII compliant edge servers, the MECS-7210 is designed to meet stringent requirements by delivering a high level of deployment flexibility, reliability, scalability, and carrier-grade processing performance further augmented by hardware expansion. With a 420mm system depth in a small footprint 2U chassis, all I/O front access, wide operating temperature support (-5°C to +55°C), and dual FHFL PCIe expansion slots reserved for access to acceleration hardware such as GPU, FGPA and QAT adapters, ADLINK’s MECS-7210 is a high performance COTS platform that meets varying application and deployment requirements, and enables customers to focus on differentiating their end solutions.
-
Product
PXI Data Acquisition
DAQ
Data Acquisition Module
Installation and configuration is fast and easy with standard connectors, soft front panels and Keysight connection expert. In addition, software drivers support the most common programming environments such as Visual Studio®, C, C++, Visual Basic, MATLAB® and LabVIEW™.
-
Product
FIber Based Solar Simulator
-
Provides up to 12 suns class B non-uniformity over a 12.5 mm diameter with the A4 Light Line and class C uniformity can be achieved over 18mm diameter both with a working distance of 25 cm. Provides up to 4 suns class B non-uniformity over a 12.5 mm diameter with the A1 Light Line with a working distance of 25 cm.
-
Product
Multisite Probe Card
T300 ButtonTile™
-
The Celadon T300™ probe cards are designed for long-term, multi-site, high-density wafer level reliability or burn-in tests up to 400°C. In today’s economic environment, conventional reliability data is needed quickly while eliminating the cost, electrical stress, and delay of parts packaging while maintaining a wafer performance map.
-
Product
LilyPad Temperature Sensor
-
Detecting temperature changes has never been easier. The MCP9700 is a small thermistor type temperature sensor. This sensor will output 0.5V at 0 degrees C, 0.75V at 25 C, and 10mV per degree C. Doing an analog to digital conversion on the signal line will allow you to establish the local ambient temperature. Detect physical touch based on body heat and ambient conditions with this small sensor.
-
Product
NI-9425, 24 V, 32-Channel (Sinking Input), 7 µs C Series Digital Module
785044-01
Digital Module
24 V, 32-Channel (Sinking Input), 7 µs C Series Digital Module - The NI‑9425 works with industrial logic levels and signals to connect directly to a wide array of industrial switches, transducers, and devices. Each digital input line is compatible with 24 V logic levels. The NI‑9425 offers isolation between the input and output banks from channel to earth ground. You cannot use the NI‑9425 in a CompactDAQ chassis to perform counter operations.
