Force Transducers
-
Product
Neodymium Low Frequency Transducers
-
High energy neodymium magnetic designs, complex cooling systems and new technologies for high-power handling, minimal distortion and low weight.
-
Product
Open Loop Hall Effect Current Sensors Transducers With Rectangle Windows
-
ChenYang Technologies GmbH & Co. KG
This Hall Effect current sensor is based on open loop principle and designed with a highgalvanic isolation between primary conductor and secondary circuit. It can be used formeasurement of DC current, DC pulse currents etc. The output of the transducer reflects thereal wave of the current carrying conductor.
-
Product
Acquisition Of 16 Displacement Transducers
APCI-3701-16
-
PCI interface to the 32-bit data bus Acquisition of 16 inductive displacement transducers (Half Bridge, LVDT) 16 input channels ± 10 V 16-bit resolution Measuring frequency up to 100 kHz Conversion can be triggered through software End of conversion can be inquired through software Possibility of interrupt through digital input channels (when a data or a time value is exceeded) PCI-DMA access Onboard FIFO buffers Sequence RAM 16 isolated digital I/O, 24 V Software operation Supported inductive transducers for APCI-3701Standard board APCI-3701-8 or APCI-3701-16Transducer type:
-
Product
Universal SOIC ZIF (Zero-Insertion-Force) Test Socket
Series 547
-
Universal SOIC Zero Insertion Force Test Socket. Devices with up to 44 pins can be inserted without bending or otherwise damaging the legs, since no force is required to either insert or remove the component from the socket. Accepts SOIC gull-wing and J-lead devices, up to 44 pins on .050 [1.27] lead pitch, body widths from .150 to .600 [3.81 to 15.24].
-
Product
Current Transducer
IN 1000-S
-
For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. 1000 A nominal, 3 ppm linearity over the temp. range, Very low offset drift 19.5 ppm, low noise 34 ppm peak-peak, -40 to +85°C, one compact package.
-
Product
Signal Conditioners & Measuring Transducers
-
Signal conditioners and measuring transducers ensure interference-free signal transmission in measurement and control technology. From highly compact 6 mm signal conditioners and measuring transducers through signal conditioners with functional safety to signal isolators for intrinsically safe circuits in the Ex area: our signal conditioners and measuring transducers ensure interference-free signal transmission in MCR technology.
-
Product
High Temperature Absolute Pressure Transducers
-
Our high temperature Baratron® capacitance manometers are controlled to temperatures of 150°C or higher for use use in demanding semiconductor manufacturing vacuum processes such as metal etching and nitride film chemical vapor deposition (CVD).
-
Product
Multi-Function Power Transducer
TD2418B
-
The TD2418B is a micro-process based transducer with a 16 bits CPU (Center process unit) and equipped with full-digitized measuring, calibrating and output functions.TD2418B not only can take the place of several static con-verters and measuring instruments (V, A, W, PF, VAR, WH, VARH, Hz) by single unit, but also have some special function such as Maximum measuring, Minimum measuring and comparator output. In communication, we use the most convenient and the easiest RS232 or RS485 as our standard output port, besides, we adopt Modbus Protocol, one of the most popular protocol in the world, as our standard protocol.
-
Product
Wireless Transducers with GSM Modem
-
Wireless GSM data loggers for temperature, humidity, binary-u. counter input.
-
Product
Crimp Force Monitor
638007950
-
The crimp force monitor measures the force signature of a crimped terminal and compares it to a reference crimp. Depending on the limits programmed, the measurement will pass, fail, or be suspect.
-
Product
Torque Transducers
-
Procter & Chester Measurements Ltd
A transducer is a generic name that is a device which is usually electronic that coverts a physical attribute to a measurement signal.
-
Product
Lo-PRO®file ZIF (Zero-Insertion-Force) Socket
Series 526
-
LO-PRO file Zero Insertion Force Socket. A choice of 24, 28, or 40 pin count devices can be inserted without bending or otherwise damaging the legs, since no force is required to either insert or remove the component from the socket. A metal cam provides strong, smooth action as it moves to a positive stop, compressing the double-sided contacts, ensuring a gas-tight seal.
-
Product
Non Contact Flange Torque Transducer
FF425
-
Contactless Torque Transducers with flange couplings at either end with measuring ranges from 0-100Nm up to 30kNm as standard (bespoke sensors up to 16MNm) for a variety of in line static and rotary torque measurement applications.The Datum Electronics Series FF425 non contact flange torque sensor and FF410 torque sensors have been designed to fit easily inline with any drive train or test rig using standard DIN size couplings. With Flange couplings at either end of the torque transducer, it has many advantages over other torque measurement systems on the market.
-
Product
Atomic Force Microscope
HDM Series
-
The task of identifying nanoscale defects is a very time consuming process for engineers working with media and flat substrates. Park NX-HDM is an atomic force microscopy system that speeds up the defect review process by an order of magnitude through automated defect identification, scanning and analysis. Park NX-HDM links directly with a wide range of optical inspection tools, thus significantly increasing the automatic defect review throughput. In addition, Park NX-HDM provides accurate sub-angstrom surface roughness measurements, scan after scan. Park NX-HDM, together with its industry's lowest noise floor, and its unique True Non-Contact™ technology, it is the most accurate AFM for surface roughness measurement in the market.
-
Product
AC/ DC mA Current Clamp-on Transducer
CA-60
-
This miniature clamp meter features two Hall effect sensors. For use with any multimeter with 200mV or/and 2V ranges for direct readout input impedance of least 1M ohm. High conversion factor for low DC and AC mA measurement. With the small jaw size it can fit into tight space in circuit panel or wire bundle to take the reading.
-
Product
Economical Load and Force Measurement
ELF
-
Tekscan's ELF force and load measurement system matches the market's need for an inexpensive load and force measurement system with Tekscan's ability to deliver innovative load and force measurement solutions. The system consists of data acquisition hardware, software, and FlexiForce B201 sensors.
-
Product
Breaking Force Tester
ZDY-02
-
ZDY-02 Breaking Force Tester is applied for break force test of the ampoule, lipstick, lip cream and other materials.
-
Product
AC Voltage and Frequency Transducers
NMTU/F
-
The NMTU/F device is an AC voltage and frequency transducer with two independent analogous outputs. The A output measures AC voltage, the B output measures the frequency of input voltage. That´s why one single NMTU/F transducer is able to replace two customary transducers, thus making it possible to achieve significant savings in installation space.
-
Product
Quartz Charge Force Rings
-
Ring-style sensor configurations measure dynamic compression. Tension measurements are also possible if the unit has been installed with proper pre-load.
-
Product
Power Transducers and Load Loggers
-
Power Transducers and Load Loggers by Ametek Power Instruments
-
Product
Force Measurement
-
Imada offers a complete selection of force measurement tools including force gauges, test stands and attachments. The gauges can be used by hand or combined into customized force measurement systems capable of addressing a wide variety of applications and budgets.
-
Product
Transducer Simulator
Model TS-16
-
Impedance: 350 ohms nominal. Output Ranges: Fixed rotary switch: 0 to 3 mv/v in 15 steps of .2 mv/v
-
Product
3-Phase AC Voltage Transducer
ENVIROMUX-PT3-600
-
Monitors and reports voltage of any 3 phase circuit. Remotely detect blown fuses or tripped circuit breakers. Three 600 VAC inputs, three 4-20 mA outputs. Inputs and outputs isolated from one another. Frequency: 50/60Hz. Maximum primary current: 600 volts. Accuracy: ±0.25% F.S. @60Hz. Output: 4-20 mA. "Zero" adjustment for accurate 0 VAC reading, and "Calibration" adjustment for frequency and voltage level. Powered by the ENVIROMUX-S420MA-24V. Regulatory approvals: UL, CUL, CE. Requires two ENVIROMUX-S420MA-24V to monitor three phases. Caution: installation should be performed by qualified electricians only. Make sure electrical service is disconnected before making any electrical connections.
-
-
Product
Electromagnetic Force Micro Tester
Micro-Servo
-
This is a multi-functional fatigue testing machine suitable for specimens, structures and full-sized parts. It is an overhead actuator type with a broad test space, so it is ideal for various types of environmental tests, such as those in corrosion tanks or constant temperature tanks.
-
Product
Transducer Calibration
-
When it comes to finding the perfect transducer calibration system, look no further than MB Dynamics. Our Calibration Systems offer an extensive range, from the Win475-Basic, the trusted calibration solution for the United States Air Force; to the first of its kind Win475-TS, which measures a transducer’s transverse sensitivity. No matter what your needs, you’ll find the calibration equipment that works for you.
-
Product
Tensile Compression Force Tester
ESM303
-
The ESM303 is a highly configurable single-column force tester for tension and compression measurement applications up to 300 lbF [1.5 kN], with a rugged design suitable for laboratory and production environments. Sample setup and fine positioning are a breeze with available FollowMeTM force-based positioning - using your hand as your guide, push and pull on the force gauge or load cell to move the crosshead at a variable rate of speed.
-
Product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type G, Ø1.50mm, 230gf
K100-G150230-SKAU
Spring Probe
K100 Series, Pitch 100mil, Tip Style G, Tip Diameter Ø1.50mm, Spring force 230gf, Steel with Gold Plating.
-
Product
Pressure Transducers
-
Alicat Scientific, Incorporated
Use pressure transducers to rapidly measure absolute, gauge, or differential pressure. Common configurations include portable and anti-corrosive designs. Custom build options include anti-corrosive and portable configurations.
-
Product
CLAMP-ON, Closed-Loop Current Transducer With “FIXED CORE” Performance
CTH Series
-
The CTH Series Closed-Loop Current Transducer is engineered for precision and reliability, allowing for accurate measurements of direct current (DC), alternating current (AC), and pulsed currents within a vast range of 100A to 10kA. This specific model, the CTH-100, boasts an extraordinary total accuracy of less than 0.1%, comparable to “Fixed Core” transducers, ensuring a high level of performance. The device employs high-resolution Hall sensors to monitor magnetic fields, thus providing superior linearity and significant immunity against external interference. Installation is made easy with its clamp-on design, eliminating the need to interrupt the primary circuit while still allowing for accurate measurements up to a frequency bandwidth of 3kHz. Moreover, the CTH-100 incorporates an advanced degaussing process to eliminate any remanent magnetic fields within the split cores, ensuring continual accuracy and reliability. With features such as a differential output at a BNC connector, a robust temperature range of -40°C to +70°C, and exceptional stability, the CTH-100 is ideal for a myriad of applications including power electronics, motor and generator control, and process control. Whether in industrial or laboratory settings, this transducer provides unmatched performance and usability.
