Ground Fault
-
Product
Accessories: Intermittent Fault Emulator
-
The Intermittent Fault Emulator (IFE) is the solution. The IFE enables manufacturers, suppliers and operators of any Intermittent Fault Detection (IFD) tester to demonstrate and verify its capabilities to detect and isolate intermittent faults.
-
-
-
Product
Cable Fault Locator System
-
Kvtester Electronics Technology Co.,Ltd
To test the HV arcing fault of cable, earthing high &low resistance, short circuit and breakage of the cable, poor contact, etc. If equipped with fault locator, it can decide the exact broken position of the cable ,applies to power cable in various type, voltage and communication cable
-
Product
Detection of PtG and PtP Faults in Line Networks
LineTroll 110Tμr
-
The indicator is powered by replaceable long-life lithium batteries which have a life expectancy of 10-15 years. It provides a 360 degree visibility for indication both for transient faults and permanent faults.
-
Product
PXI Fault Insertion Switch, 7-Channel, Two Fault Buses, 20 A, Hardware Interlock
40-193A-002-HI
Fault Insertion Unit
The 40-193A-002-HI is a 7-Channel Fault Insertion switch with hardware interlock and two fault buses, designed for the simulation of fault conditions in automotive systems. The module is capable of switching current up to 20A.
-
Product
Common Point Ground Connector
Q007-T
-
The Prostat Q007B Qube™ replaces ordinary electrical grounding devices with a convenient, cost effective means to connect several ESD controls to a single grounded electrical outlet. Use the Q007B Qube™ to ground workstations, mats, wrist strap & testers, instruments, and other ESD control products to a pre-tested facility electrical ground. It consists of a robust multi receptacle frame encased in fire retardant ABS with a solid brass grounding pin.
-
Product
Cable Fault Location System
Syscompact 2000 M Pro
-
Cable fault location system 2000 M pro. The portable BAUR Syscompact 2000 M pro cable fault location system is used for cable fault location and cable testing in low- and medium-voltage cables up to 65 km length.* Fully integrated proven cable fault pre-location methods* Surge mode for acoustic pin-pointing* Easily transportable* Ideal for locations that are difficult to access
-
-
-
Product
PXI Fault Insertion Switch, 6-channel, Two Fault Buses, 10 A
40-192A-012
Switch Module
The 40-192A-012 is a PXI fault insertion switch using solid state switching elements and is capable of switching current up to 10A. It is designed to be able to insert three different fault conditions between the test fixture and the equipment under test
-
Product
Visual Fault Diagnostics and Repair System
ScanExpress Viewer
-
ScanExpress Viewer™ is a printed circuit board (PCB) CAD data & photograph visualization tool for boundary-scan test development, electronic manufacturing test, and product repair environments.When combined with ScanExpress ADO™ (Advanced Diagnostics Option) for detailed results from ScanExpress Runner™, ScanExpress Viewer displays fault coordinates and connected traces superimposed directly on a board photograph or CAD layout diagram for expedient repair.
-
Product
Cable Fault Location System
BAUR Syscompact 2000 Portable
-
Cable fault location system Syscompact 2000 portable. The cable fault location system Syscompact 2000 portable is used for precise location of high-resistance and intermittent faults in low and medium voltage cables.* Fast and reliable* Precise, dependable cable fault location* High performance high voltage unit* Integrated proven cable fault pre-location methods
-
Product
Long Spring Ground for ZD Differential Probe Qty 2
PACC-ZD003
-
Long spring ground for ZD differential probe Qty 2
-
Product
Cable Fault Locator With Time Domain (Intelligent Bridge)
GT00ZD00ZY
-
GAOTek Cable Fault Locator with Time Domain has a reflectometer to locate faults in metallic cables and Intelligent bridge for tesing the broken line
-
Product
7U VPX 1 Slot Power & Ground, 3.125G
101VPX701P-1X40R
-
3.3V, 5V and 12V power, rear connectors fully loaded. Use with Elma’s slot-to-slot or slot-to-I/O bulkhead cable products for system development.
-
-
Product
Generator Neutral Grounding & Leads Cubicles
-
Generator Neutral Grounding Cubicles are designed to minimize fault damage incurred by generators, maintain sufficient fault detection and improve power system reliability. Generator Neutral Grounding and Lead Cubicles are manufactured as for IEEE or IEC standards.
-
Product
Resistance, Ground Testing, Battery And Power Quality
-
Our testing equipment works wherever you are, whenever you need it, with precision and reliability.
-
Product
AC Hipot w/ Ground Bond Test Capability
HypotULTRA® Series
-
In a world where data is king, HypotUTLRA improves traceability with on-board data storage and allows you to automate hipot testing with a variety of communication interfaces. Increase efficiency with our direct barcode scanner connection and intuitive touch screen interface. Models 7804 and 7854 are a 4-in-1 solution with the addition of 40A AC Ground Bond test capability added to HypotULTRA's already impressive feature list. HypotULTRA is a dielectric analyzer designed to take your production line to the next level.
-
Product
3D Ground Penetrating Radar data processing & Interpretation software
Condor
-
Condor is modern processing, visualisation and interpretation software for the efficient management of Raptor 3D GPR array data.Boost performance and improve workflows.- Efficient sub-surface imaging- Effective workflows- Simple and intuitive- Dedicated to processing Raptor data- Modern Windows software (64-bit)
-
Product
AC Ground Bond Tester
446
-
Our 446 model is a 4-in-1 tester with AC Hipot, DC Hipot, Insulation Resistance, and Ground Bond capabilities. This tester features a simple design and easy-to-use interface, reducing setup time and increasing production-line throughput for your application. The 446 is equipped with multiple memories and an optional USB port for remote BUS communication so you can quickly perform tests on a variety of DUTs from the front panel or with a PC. Add to user safety by equipping your tester with Personal Protective Equipment (PPE) via the built-in safety interlock.
-
Product
Visual Fault Locator
-
Shanghai Baudcom Communication Device Co.,Ltd.
This Pen-type VFL is specially designed for field personnel who need an efficient and economical tool for fiber tracing, fiber routing and continuity checking in optical networks. It finds breakpoints, poor connections, bending or cracking in fiber optic cables
-
Product
Dual Bus 75-Channel 2A PCI Fault Insertion Switch
50-190-002
Fault Insertion Unit
This PCI fault insertion switch range is available with 75, 64 or 36 channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. The Stimulus/Measurement to UUT path is suitable for supporting CAN and FlexRay bus systems.
-
Product
PXI 5A Fault Insertion Switch 5-Channel
40-196-101
Fault Insertion Unit
The 40-196 is a 10 Channel 5A Fault Insertion Switch, primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. It is designed to be able to insert different fault conditions between the test fixture and the equipment under test: Open-Circuit, Short-Circuit between signal pairs, Short-Circuit between signal pairs and user applied fault conditions e.g. Power or GND. Shorting relays on each channel enable UUT signals to be subjected to external user applied fault conditions or to be shorted to the adjacent signal in the same channel. Relays in line with the signal allow open circuit conditions to be simulated on either side or both sides of a channel signal pair. The switching topology of the 40-196 allows channels to be interconnected so that complex fault insertion systems can be constructed.
-
Product
Fault Recording Monitors
-
Comprehensive, flexible, scalable and compatible – full multi-function devices.
-
Product
Fault Level Monitoring
-
The fault level or fault current is the maximum current to flow on a network in the event of a fault.
-
Product
Cable Fault Testers
-
*Compact and lightweight solution for underground cable testing*DC Hi-Pot test of de-energized, shielded underground primary cable*No external power required - self-contained 8kVDC voltage source*Can be used up to a distance of 1500 ft (457m)*Clear and simple test results - analog bar graph and indication of good or faulted cable*Safety feature - measures AC voltage before converting to a DC voltage tester*Lightweight, single hot stick operation for testing cable
-
Product
3U VPX 3 Slot Power & Ground, 2 x VITA 67
1900002601-9001R
-
The only assigned pins on these backplanes are for 3.3V, 5V and 12V power, and both ground and utility planes are defined. The remaining pins are all user-defined. The rear connectors are all fully populated.
-
