Filter Results By:
Products
Applications
Manufacturers
Conditioners
-
product
Stand Alone/ Bench Top Load Cell Amplifier/ Conditioner Module
MODEL TMO-2A
The TMO-2A Transducer Modules is a complete differential amplifier/signal conditioners with self contained power. The unit provide excitation, balance and span adjustment via precision 10 turn pots, and shunt calibration necessary to couple a user supplied bridge type transducer to an indicating instrument. Zero to full scale output is specified at 4-20 mA. The TMO-2A provides a floating shunt calibration circuit which applies calibration at the transducer, thereby eliminating errors due to line losses. The excitation supply incorporates a Wagner Ground to greatly improve Common Mode Rejection. The factory set bandwidth of the module is narrow to improve stability. The removal of a single capacitor will increase the frequency response DC to 60K Hz for dynamic data applications.
-
product
8-Channel VME Strain Gauge/Load Cell Module
V385
The V385 is a VME/VXI compatible eight-channel strain-gauge signal conditioner applicable to generic bridge-type transducer applications. The V385 adds individual remote-sensed excitation supplies to each channel, increasing its precision over the V380's single excitation supply.
-
product
DIN Rail Mount
Encore Electronics offers a complete line of compact, economically priced instrumentation packaged in standard DIN rail mounted enclosures. Our products include frequency to voltage converters, strain gage amplifiers, notch filters, accelerometer conditioners, and line drivers. Overall package sizes are 3.1″ x 3.3″ x 0.9″ tall (single wide) or 1.6″ tall (double wide).
-
product
Signal Conditioners & Interface
Modbus RTU Remote Connectivity and Control. Minimize Long Cable Runs with Modbus Network. Pulse to Frequency Conversion. Shaft Speed Pulse to DeviceNet. Shaft Speed Pulse to 4-20 mA Conversion.Sensor Compatibility
-
product
Digital Panel Meter
DC
Laureate DC voltage and current panel meters with a DC signal conditioner board combine high accuracy with high read rate and a wide range of isolated output options for computer interface and control. Accuracy is 99.99% of full scale 1 count. Used as a direct-reading DC voltmeter, the Laureate provides a full-scale readout of 20,000 counts and six full-scale voltage ranges from 200.00 mV with 10 mV resolution to 600.0 V with 100 mV resolution.
-
product
Signal Conditioners
SC-1300
The SC-1300 family of signal conditioners can convert the most commonly used process signals into conditioned current and voltage outputs, needed for control systems and monitoring devices. Dedicated functionality and isolation from control systems improves reliability.
-
product
Temperature Controllers
Panasonic Industrial Devices Sales Company of America
Panasonic's line of versatile Temperature Controllers are offered in a wide selection of inputs and outputs, including PID (built-in auto-tuning function included), analog signal conditioners with scaling, and panel meters with a very bright and easy to read display. The KT line of controllers (pictured) is well suited for a wide variety of machine and process control applications.
-
product
Instrumentation And Signal Conditioners Products
Stellar Technology offers a full line of readout meters, in-line amplifiers and signal conditioners to complement our broad variety of pressure, load/force/torque, displacement, and temperature sensors. If you’re in need of reliable signal conditioners for your essential operations, our diverse options can provide a solution. Read on to discover all that Stellar Technology can offer your company.
-
product
Band-On Telemetry System
Advanced Telemetrics International
The ATi Band-On Telemetry System transmits real-time sensor data from a rotating shaft while the system is running. The system consists of one or more rotating signal conditioner/ transmitter modules with battery pack and a stationary receiver. Rotating transmitters are available to interface with most any type of sensor including strain gages, thermocouples, thermistors, RTDs and accelerometers.
-
product
Multi-Conductor Cables
16 Channel, multi-conductor cables are shielded and wired for PCB® equipment specifically. Shielding minimizes noise when located near other power or signal cables. Custom versions are also available on request. Instrumentation-grade BNC / DB-50 connectors are provided to interface with Patch Panels and Signal Conditioners.
-
product
Cover Extend Feature, GTE 10.00p
K8217A
Cover-Extend Technology (CET) extends the Boundary Scan limited access solution on non-boundary scan devices with the use of VTEP or nanoVTEP and CET signal conditioner card hardware.
-
product
Signal Conditioner
DMA2
Din rail mountable with user selectable outputs of +/-10V, +/-5V or 4-20 mA. 10-28VDC powered suitable for battery or automotive use. Features 1000 Hz bandwidth and push-button shunt calibration.
-
product
Cover Extend Feature, GTE 10.00p
K8217B
Cover-Extend Technology (CET) extends the measurement capability of VTEP or nanoVTEP into powered testing by using the Boundary Scan output cell to test the connectors and socket signal pins. This capability extends the Boundary Scan limited access solution on non-boundary scan devices with the use of VTEP or nanoVTEP and CET signal conditioner card hardware.
-
product
Signal Conditioners
General Purpose
Encore offers a complete line of General Purpose Signal Conditioning instrumentation to meet even the most demanding requirements. Packaged as interchangeable two-channel plug-in modules, Encore’s broad product line includes frequency to voltage converters, strain gage amplifiers, accelerometer conditioners, digital voltmeters and DC power supplies. All of our systems feature a common CAL input on the rear of the rack which allows for calibration of the entire rack. Calibration function varies based on the modules installed. For example, the Model 633 applies a shunt calibration resistor across the bridge, while the Model 149 applies a reference charge source to the input. Contact Encore today and let our team of design engineers help you determine which of our products is best for your application.
-
product
Turnkey Laboratory Acquisition Systems
Series 6800 for laboratory applications is a ready-to-run, high performance measurement system. Enclosures are 3U rack mountable or can be used right on the desktop. 6800 units come equipped with a conditioner, amplifier, filter and digitizer. Each channel has a front mounted connector specific to a measurement type: RJ-45 for 8-wire bridge transducers, BNC for voltage or ICP/IEPE inputs or a 3-wire military grade connector.
-
product
AC Control Time Switch
IM1756
Ajinkya Electronic Systems offers AC and water cooler controller, an energy saving device for controller air conditioner unit and water cooler optimally to save Electricity. AC Control Time Switch offers unparallel features to not only save energy but to save compressor from electrical voltage and overload.
-
product
Intelligent Panel Mount Meter Amplifier/ Conditioner
MODEL DPM-2
The voltage-to-frequency microprocessor makes Transducer Technique's 4-digit panel mount meters the ideal solution for meeting the measurement, display and control requirements of noisy industrial applications, OEMs and system designers. Model DPM-2 accepts any full bridge transducer. Balance and span can be selected via the front keypad, thus allowing the display to read directly in engineering units. Front panel max and tare functions are ideal for industrial weighing applications. Isolated adjustable 9-11 VDC excitation with remote sense and 90 mA drive eliminates the need for external power supplies. Rear screw terminals connectors are included.
-
product
Data Acquisition & Signal Conditioners
Electro Standards Laboratories
Electro Standards Laboratories offers instrumentation and signal processors in both encased form factors or board-only versions suitable for embedded sensor applications. Features ability to collocate with sensor and provide immediate digitization and signal processing in order to minimize ambient interference on sensitive sensors and to seamlessly integrate into networked sensor architectures.
-
product
High Pressure Gas Conditioners
HPG
Bemco HPG, High Pressure Gas Conditioners are similar to the PTS Portable Temperature Conditioners except they are designed for continuous operation at up to two atmospheres (29.4 psia) of pressure. This higher base operating pressure doubles the gas density per cfm of circulating air or gaseous nitrogen allowing the use of smaller connecting tubes while also increasing thermal capability. .
-
product
High Speed Logic and Data Path Management
The ADI Data Path Management portfolio offers Data Path Signal Conditioners, Digital Crosspoint Switches, Level Translators, Serializer/Deserializer & Selector Muxes and Track/Hold Amplifiers for meeting the tight requirements of modern high data rate system. ADI's system solution focused products are easy to integrate to any signal chain with single supply usage while achieving low jitter, high output swing, fast rise/fall time.
-
product
Low Frequency Vibration Signal Conditioner
A compact Signal Amplifier to make optimal signal processing being connected with the Servo type Accelerometers. It is used for Vibration Acceleration Measurement, Waveform Observation, for various Analysis in combination with the AC Voltage Meter, Oscilloscope, FFT Analyzer respectively. Furthermore, Voltage signals from the Microphones or Sound Level Meters can be output to the instruments like Recorders along with the Vibration Signals.
-
product
Crosspoints and Signal Conditioners
Macom Technology Solutions Holdings Inc.
Crosspoints and Signal Conditioners
-
product
Disconnection Detector for PV
NSEI-100D
MULTI MEASURING INSTRUMENTS Co., Ltd.
*This device can detect the disconnected & broken point of DC current lines between PV panels and power conditioners in PV systems, without cutting power off and without climbing the roof where PV modules are located.*Furthermore, this model can find out the disconnecting point by applying the attached detector to the specific PV module.
-
product
Seismic Signal Conditioners
Seismic signal conditioners are designed to accept an input from (and provide power to) a seismic sensor. They convert the signal to a proportional 4-20mA DC signal that can be used as an input to process control instrumentation such as a PLC or DCS. They provide additional convenience features such as optional displays, BNC connectors for access to the dynamic sensor signal, and bandpass filtering. Metrix offers seismic signal conditioners that can accept either acceleration or velocity sensors, and are available with or without an integral display.
-
product
Power Distributor / Conditioner
AV-P2803
The "AV-P2803" is a power distributor / conditioner for equipment that uses a 3P outlet and is capable of long-term sequence operation and external control for systems including network devices.
-
product
Gas Distribution Panels
PTS DII
PTS DII Gas Distribution Panels are similar to our PAO-DII Fluid Distribution Panels. They are designed to individually distribute, monitor, and protect one or more of your valuable products from the higher than required flow of a larger PTS, Portable Temperature Servo Conditioner or HPG, High Pressure Gas Conditioner. You can also use PTS-DII Gas Distribution panels with any other source of temperature controlled gas, including a competitor's air or gas source.
-
product
Signal Conditioners
The Series 8000 Signal Conditioners are designed with a state of the are modular architecture to allow full input, output, and special function selectability and interchangeability. They can also be used as isolators, signal amplifiers and transmitters.
-
product
500 Watt AC/DC Power Line Conditioner, 3U VPX, Holdup Time
VPX56-3HU
NAI's VPX56-3HU is a rugged, high-performance 500-Watt Output +28 VDC Input 3U VPX AC/DC Power Line Conditioner designed for aerospace, defense, and industrial markets. This off-the-shelf power supply plugs directly into a standard VPX conduction cooled chassis and protects downstream DC-DC converters from MIL-STD-704 transients, low-voltage conditions and power interruptions, providing up to 50 milliseconds of holdup time at up to 500-Watts. Continuous Background Built-In-Test (BIT) and I2C communication are included.
-
product
Test Setup For Air Conditioner
SCR ELEKTRONIKS have developed TESTING SET UP FOR SINGLE PHASE / THREE PHASE MOTOR for carrying out Performance Test, Earth Contact Resistance Test, High Voltage Test, Megger Test and Leakage Current Test. It consists of Voltmeters, Ammeters and Wattmeters for observing the values of different parameters. OK / NOT OK lamps are also provided to display the results of Earth Contact Resistance Test, HV test, Megger Test, Leakage Current Test. All tests are provided with tripping cut off concept.
-
product
Three Channel AC Magnetic Field Signal Conditioner
TCM-1A
Macintyre Electronic Design Associa
The TCM-1 is a three-channel portable signal conditioner specifically tailored to provide power to and process the signals from MEDA's line of AC magnetic field sensors. The unit operates from either its internal batteries or the power line. It incorporates two sets of power line rejection filters, switch selectable for 50 or 60 Hz and the corresponding first four harmonics.
