Pressure Calibrators
Provide precision simulation of known values to ascertain pressure instrument graduation deviation.
-
Product
Photometric Ozone Calibrator
Model T703
-
Teledyne Advanced Pollution Instrumentation
The Model T703 is a microprocessor controlled ozone calibrator for precision gas analyzers. The Model T703 can deliver concentrations from 50 ppb to 5 ppm at flows from 1 LPM to 5 LPM.The Model T703 has two major components; the ozone generating device and the photometer. The ozone generator produces ozone by passing zero air over a UV lamp. Flow rate and lamp intensity are adjusted to deliver a specified ozone concentration by volume. The temperate and pressure compensated photometer, identical to that of the Model T400 ozone analyzer, provides feedback control of the UV lamp intensity, assuring stable ozone output. A nearly unlimited number of calibration sequences may be programmed into the non-volatile memory of the T703, covering time periods up to a year.
-
Product
High Pressure Test Chamber
-
Guangdong Test EQ Equipment co., Ltd.
- Capacity(L): 500~50,000L（Customizable）- Working pressure: -0.1~50MPa- Control Accuracy: ≤±0.0002 MPa- Pressurization Rate:Ambient Pressure→0.8MPa ≤30min- Depressurization Rate: 0.8MPa→Ambient Pressure ≥30min- Humidity Control:20–80% RH
-
Product
Calibration Services
-
Your CLIO hardware can be furnished with (or be submitted for) a SIT Certificate of Calibration. This document, produced by a laboratory accredited by the Italian Calibration Service, reports measurement data of the primary quantities generated and analyzed by the instrument (AC Voltages) traceable to National and International Standards. This document is usually requested for ISO compliance.
-
Product
Digital Tire Pressure Gauge
162
-
*Accurate digital tire pressure readings! *Reads in PSI, KPa & Bar *Backlit LCD display *Built-in LED Flashlight can be used while taking readings
-
Product
Non-Invasive Blood Pressure Simulator
SC-5 SimCube® NIBP
-
The STANDARD SC-5 SimCube® NIBP Simulator provides ECG, Respiration, Arrhythmia, Pacer Simulation, IBP and three Digital Manometer Modes of tests.
-
-
Product
Network Analyzer N-Port Calibrated Measurements
S95551B
Network Analyzer
PXI vector network analyzers (VNA) offer the capability to extend the number of ports for your measurements by using additional modules. When multiple modules are used, they are configured for multiport operation. The S95551B adds a multiport analyzer mode that enables full multiport error correction and measurement capabilities. The instruments may be identified as one VNA by the firmware running on an external host PC. At least one VNA instrument connected to your PC must have one S95551B license to maintain N-port capabilities.
-
Product
Relative and Differential Pressure Transmitters
HD408T… / HD4V8T… Series
-
HD408T, HD4V8T are analog output relative or differential atmospheric pressure transmitters; they are used in all those applications where non corrosive air or gas need to be monitored, with pressure fields from 10 mbar to 2000 mbar.
-
Product
Testwave Calibration
-
Testwave® LLC calibrates electronic, physical, & dimensional test equipment. Our Sparks facility includes a state-of-the-art temperature controlled calibration laboratory, which holds the temperature to within +/- 0.5°C. We send you recall notices before your equipment calibration expires, and if we don’t hear from you, we will call, to make sure you stay in compliance with your calibration requirements. Calibrations are performed at your facility, or at our Sparks Nevada laboratory.
-
-
Product
Pressure Sensors
ESCP-MIS1 Sensor
-
ES Systems has developed a series of medium isolated pressure sensors suitable for applications with harsh environmental conditions where resistance to corrosive fluids or gases is required. Each sensor integrates a MEMS capacitive pressure sensor die, and a CMOS ASIC for the signal conditioning. The MEMS pressure sensor dies are underpinned by ES’s innovative microfabrication process for silicon capacitive sensors.
-
Product
Differential Pressure Transmitter Trainer
-
Unitech Scales And Measurements Pvt. Ltd
This table top model comprises of two pressure chambers. One for high pressure and another for low pressure. The two pressure chambers are fitted with pressure gauges. The differential pressure transmitter is connected to the two chambers. The pressure is built by a foot air pump. Digital instrument is provided to indicate the differential pressure with transmitter output.
-
Product
4-in-1 OSLT Calibration Kit, DC to 40 GHz, 2.92 mm (m)
CK562A
-
The Network Analyzer Calibration Kits with open, short, load, and thru (OSLT) provide the RF components needed to enable stable and accurate error correct measurements. Calibration of a network analyzer using Spanawave's Network Analyzer Calibration Kits allow for precise measurements. The Calibration Kits offer broad test equipment coverage for use with the 8003 Scalar Network Analyzer as well as being compatible with most network analyzers produced by other manufacturers. Spanawave calibration kits yield complete calibrations, as it takes into consideration the three major sources of systematic error correction by one port calibration at both ports.
-
Product
Vibration Transducers Calibration System
-
The system is used for calibration of vibration transducers as well as:*ICP and charge accelerometers;*piezoelectrical and capacitive vibration transducers;*vibration-measuring instruments.
-
Product
Heat-Resistant Test Equipment Ball Pressure Tester
CX-Q002
-
Shenzhen Chuangxin Instruments Co., Ltd.
Ball Pressure Tester is used for testing parts of non-metallic materials for resistance to heat. It is applicable to electrotechnical equipment, its subassemblies and components, and to solid electrical insulating materials except ceramics.
-
Product
Lens Calibration
SpyderLENSCAL
-
A fast, reliable method of measuring and adjusting the focus performance on your camera and lens combinations.
-
Product
Pressure Testing
-
All metal, plastic, and composite parts intended to contain liquids or gases under pressure are required to undergo stringent pressure testing procedures to meet qualification standards.
-
Product
Evaluation Kit for Differential Pressure Sensors of the SDP3x Series
EK-P4
-
The evaluation kit EK-P4 is designed for an easy and cost-efficient evaluation and qualification of Sensirion's SDP3x differential pressure sensors. Test now the features of the new differential pressure sensor. Especially at lowest pressure differences, the sensor provides highest accuracy and long-term stability.
-
Product
Argon Calibration Source
AR-1
-
The AR-1 produces low-pressure argon emission lines from 696-1704 nm for use in performing fast, reliable spectrometer wavelength calibrations.
-
Product
Calibration Management Software
MET/CAL®
-
MET/CAL software is structured around the flow of instruments through the calibration process and addresses a wide range of test and measurement instrument calibration needs, from the simple to the complex. It is based on the traditional calibration model as its framework—comparing an instrument to a standard of known uncertainty.
-
Product
Real-Time X-Ray Imaging and Variable Pressure Scanning Electron Microscope
-
Trialon has the equipment and experienced staff to operate this highly technical piece of laboratory equipment. Our state-of-the-art materials analysis lab located in Auburn Hills, MI is managed by a Ph.D with over 20 years of hands-on experience in root cause failure analysis of design, material and process for current and future products.
-
Product
Modular Type SELEX FRL Regulator Mounting Dedicated Digital Pressure Sensor
PPR
-
This is a digital pressure sensor dedicated to mounting a modular type regulator.Displayed values and set values can be checked at the same time on a 2-screen display.You can check the displayed value (current value) on the main display and the set value on the sub display.
-
Product
Onsite Calibration Services
-
Tempsens offers NABL Accrediated on-site calibration i.e. calibration of temperature sensors at customers plant or site.Our experienced and trained Engineers visit site or plant as scheduled by our customer to calibrate the instruments, usually without the time and expense of removing and reinstalling them. Work is performed with minimal disruption, and detailed documentation is provided upon completion.
-
Product
Digital Gauge Pressure
ZET 7012-I-VER.1
-
ZET 7012-I-VER 1 digital gauge pressure open membrane is used for fast and simple overpressure measurements and measured values data transfer in digital format via RS-485 or 4-20 mA interface.
-
Product
Process Calibrators
-
Handheld calibrator-multimeter of industrial process signals including voltage, current, resistance and temperature. External signals up to 200 V or 100 mA can be measured simultaneously with signal sourcing.
-
Product
Horizontal Calibration Instruments (Lab)
THV
-
The horizontal THV instrument has been designed for calibration and certification of gauging equipment of small dimension. It allows easy and precise checking of plug gauges, ring gauges, thread plug gauges, test and dial indicators as well as measuring of high precision production parts.
-
Product
Electronic Calibration Module (ECal), 26.5 GHz, 3.5 Mm, 2-port
N4691D
-
The Keysight N4691D microwave electronic calibration (ECal) module makes calibration of Keysight vector network analyzers fast, easy and accurate. The N4691D is a precision 2-port ECal module that supports 3.5 mm connectors up to 26.5 GHz. Select either female-female, male-male, or female-male connectors. The plastic storage case for the N4691D is included for securing your ECal module and accessories.
-
Product
Impedance Standards and Calibrators
-
Impedance Calibrator is to replace countless single value RCL standards with one calibrator that can switch between the standards like a CD changer in your car. The calibrator contains stable and temperature independent resistance standards, partial capacitance standards and partial inductance standards, simulated by RC T-type passive network. Calibration values of both complex parameters of partial standards are displayed on large LCD screen in preselected pairs of parameters as well as voltage, current and frequency readouts from built-in test signal meter. OPEN and SHORT reference positions are available as well.
-
Product
Pressure Comparator (System D)
P Series
-
AMETEK Sensors, Test & Calibration
The P-Series (System D) comparators are hydraulic screw pumps designed for easy, controlled, high pressure generation. Each comparator includes a 4 connection manifold, which can be used for the reference indicator, the device under test, a fine adjust, an isolation valve, or a fluid reservoir. The adjustable reference pressure port lets you set your reference gauge at the best viewing angle. Three models are available for hydraulic oil, water, or both.
-
Product
Hydraulic Calibration for Load Cell
HLCS-10000
-
Jinan Testing Equipment IE Corporation
The Hydraulic Calibration System is specially designed for the calibration of load cells with higher capacity. The Calibration for Load Cell can calibrate the load cell within +/-1%.
