Interfaces
connections between dissimilar environments.
See Also: Serial Interfaces, Parallel Interface, Bus Interfaces, UI, MIPI, Interface Adapters, Interconnects
-
product
50 Ohm MMCX to MMCX Cable Assembly
40-977-571-2m
This 2m long MMCX cable assembly is part of the range of RF cables. Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
product
Press Down Rods Bed of Nails Testers
Protector Press Rods Family
Designed for testing heavy massive boards. Boards with heavy components like large transformers and inductors can destroy normal test fixtures. This design utilizes a 3 plate system where an internal lever actuated sub plate containing the test pins raises to probe the circuit board when the handle is pulled. Heavy boards can bend and break exposed test pins. Similarly large boards which need to be probed by very small delicate test pins can also benefit from this protected test fixture design. This fixture is recommended in situations where there is a high board mass to pin size ratio and pin protection is required. Front and rear panel modular inserts allow for easy updates and customizations to the user hardware interface.
-
product
2 Slot 6U VME 64x Backplane
DP-VME-7008
DP- VME-7008 is a 2 slot 6U VME 64x backplane designed to be used with VME boards. This module provides the interface and communication between 2 slot and the rear side mating for the rear boards.
-
product
2-Ch 3.6 GHz or 4-Ch 1.8 GHz 12-bit A/D with DDC, Kintex UltraScale - 6U VPX
Model 58841
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Ideal radar and software radio interface solution- Supports Xilinx Kintex UltraScale FPGAs- One-channel mode with two 3.6 GHz, 12-bit A/D- Two-channel mode with four 1.8 GHz, 12-bit A/D- Programmable DDCs (Digital Downconverter)- 10 GB of DDR4 SDRAM- µSync clock/sync for multiboard synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x8- Optional LVDS and gigabit serial connections to the FPGA for custom I/O- Compatible with several VITA standards including: VITA-46, VITA-48 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- Synchronize up to twelve modules with Model 9192 System Synchronization and Distribution Amplifier- 1U Rack-mount
-
product
Flexible x4 PCI Express to 4 MiniPCI Express Splitter
SKU-072-0X
Flexible x4 PCI Express to 4 MiniPCI Express Splitter (Splitter) was designed to expand modern motherboard (ATX, mini ATX etc.) that have PCI Express interface. It allows connecting up-to four MiniPCI Express add-in expansion boards to the standard motherboard PCI Express connector.Splitter includes 4 MiniPCI Express Adapter boards, x4 PCI Express Host board and 4 Flat PCI Express Cables.
-
product
Development System
FE-51MX
* Emulates Philips P8xC51MA/B/C , P89C669 Microcontrollers * 1MByte Code Memory * Based on bond-out Technology * Frequency up to 24MHz 3V / 5V Operation * Huge Real Time Trace Memory * Windows Debugger for C/C++ and Assembler * Target Board Included * RS-232 or USB Interface * 64K C/ASM and 8K C++ Included
-
product
Vegas Data Diode
01-09838
Non-ruggedized module that addresses concerns regarding use of untrusted, commercial-off-the-shelf (COTS) bus logging on aircraft with a MIL-STD-1553 or ARINC-429 bus interface.
-
product
PCI Express 16 Isolated Input Digital Interface (3-13V)
8006e
The 8006e PCI Express digital I/O interface provides 16 optically isolated inputs for connection to devices including sensors, switches, pushbuttons, and other user inputs. The inputs can sense both AC and DC voltage while providing optical isolation, which eliminates spikes and surges present in industrial environments. The board is PCI Express X1 compliant and is compatible with any PCI Express slot.
-
product
8 GHz Differential Probe with ProLink Interface
DH08-PL
Teledyne LeCroy’s DH series 8 to 30 GHz differential probes offer the combination of bandwidth, input range and offset capability to address any high-speed probing requirement from debugging serial data interfaces to validating DDR memory systems. DH series probes provide superior loading characteristics and are calibrated with a custom “fine-tuned” frequency response. The ultra-low loading and flat frequency response ensure accurate measurements.
-
product
FMC Loopback Test Board
The FMC loopback tester board enables developers and assembly factories to test and characterize the FMC carrier board interfaces. The board features full differential loopbacks on all the FMC high pin count (HPC) connector interfaces including LA, HA, HB, DP and CLK. It also provides a 125MHz transceiver LVDS reference clocks on GBTCLK signals. The FMC loopback board is based on VITA 57 standard with ruggedized conduction or air cooling.
-
product
3-in-1 Analyzer: Logic Analyzer, Protocol Analyzer, Simple DSO
MSO2216B
3-in-1 Analyzer : Logic Analyzer, Protocol Analyzer, Simple DSO• PC-based, USB3.0 interface• 8 / 16 Channels(display digital and analog waveforms of the same channel)• Digital Inputs : 2 GHz Timing, 200MHz State Analysis (Max.)• Analog Inputs : 200 MS/s (Max.), Bandwidth 40 MHz• 8 Gb Memory (Max.)• PC RAM storage for streaming mode• Utility model patent of Taiwan number M601827
-
product
ARINC 664 Simulator & Analyzer Applications Software
F-SIM-A664
Avionics Interface Technologies
Software GUI Application for Operating AIT ARINC 664 Interfaces - Simulate Multiple ARINC 664 End Systems Simultaneously - Full definition of input/output VLs, input/output Sampling and Queuing message ports, & TFTP Clients & Servers - Capture & Analyze Data from Multiple Virtual Links (VLs) - Live display showing all of the detected ARINC 664 VLs and message counts - Live displays showing all of the detected source and destination message (UDP) ports - Record network data to PCAPNG for use with Wireshark - Replay Previously Captured Bus Data - Also Supports MIL-STD-1553, ARINC 429 & Data Load operations
-
product
Cable Assembly, 50-Pin D-Type, Male to Unterminated With Cut Ends, 2m
A050DM4-C-0A200
The 50-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated wire and can be secured to the product by screwlocks. The 50-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
-
product
ICP-OES Analyzer
SPECTRO ARCOS
SPECTRO Analytical Instruments GmbH
The SPECTRO ARCOS ICP-OES excels in industrial and academic applications for the most advanced elemental analysis of metals, chemicals, petrochemicals, and other materials.Its unique new MultiView plasma interface option provides truly uncompromising axial-view and radial-view plasma observation in a single instrument. The periscope-free MultiView mechanism lets an operator literally "turn" a radial-view instrument into an axial-view device, or vice-versa, in 90 seconds or less. Visit the MultiView Q&A section in the ARCOS Resource Center for answers to frequently asked questions. Plasma power enters a whole new era with the system's innovative generator. This unique, compact and extremely rugged component is based on laterally diffused metal oxide semiconductor (LDMOS) technology. It delivers the highest plasma power available today, enabling previously impossible feats of analysis at the highest plasma loads.
-
product
Half Slim SATA3 RunCore Embedded SATA3 “Elite Series”
RunCore Innovation Technology Co. Ltd.
Half Slim SATA3 utilizes high-performance SATAIII SSD controller and NAND flash, with or with no DRAM buffer to support power failure mechanism. This series SSD compliant with Serial ATA Revision 2.6/3.1 specification, compatible with 6.0Gbps, 3.0Gbps and 1.5Gbps interface rate and support Native Command Queuing (NCQ) up to 32 commands. As a standard SATA drive, it can support mainstream OS, such as Windows/Linux/Unix/Solaris/ Mac OS and so on.
-
product
Video & Vision Cards
Advantech’s video and vision cards offer multi-channel image/video compression, transmission, and streaming capabilities for diverse interfaces.
-
product
16/8 Channel 14 bit 500 MS/s Digitizer
V1730 / V1730S
The V1730S comes in a VME form factor, with 16/8 input channels. The communication to and from the board is provided through the VMEBus and Optical Link interfaces.
-
product
Digital Anemometer
Anemometer is a high-quality instrument providing highly accurate air velocity measurements in harsh environments via a user-friendly & intuitive interface.
-
product
8 Channels, Differential Input
VR1
The VR1 provides eight isolated, wide voltage input range Variable Reluctance (VR) signal or general-purpose Pulse Counter measurement interfaces. Channels can be programmed to operate individually or combined in pairs.
-
product
OEM service
CoolLED has the technology and experience to design and build LED illumination systems to meet the needs of manufacturers who wish to integrate stable, controllable illumination within their products. Working closely with our engineers, you will be able to define the spectral performance and interface by drawing upon CoolLED’s expertise. We have been providing our OEM partners with LED illumination for their systems for over five years. Take a look at our dedicated NEW website www.OEMIllumination.com
-
product
PXI Semi-Dynamic Digital I/O Module, 32-Channel
40-419-003
The 40-419-003 is a 32-channel digital I/O module suitable for operating external devices, such as power, RF and high voltage relays, solenoids and lamps. It can also be used for interfacing with external logic such as a programmable instrument with a BCD interface depending upon the module’s driving capabilities.
-
product
Video Microcope
BVM-20101
High-resolution CCD sensor, built-in analog/digital converter, analog and digital signal directly display on the screen, can also simultaneously display on TV and computer through corresponding interfaces; taking photo and video through software; easy operation, reducing user's fatigue and injury.
-
product
Duplex Double Test Insertion/Return Loss Test Station
JW8302
Shanghai Joinwit Optoelectronic Tech,co.,Ltd
JW8302 Duplex double test Insertion/Return Loss Test Station is a professional equipment to test CWDM device, multi-wavelength device, PLC, fiber optical patch cord and other passive optical devices. It is a new-generation precision optical instrument of JOINWIT who combined with so many years experience in optical passive detection. It equipped with VFL or 850 light source , supporting threshold determination, automatic multi-wavelength detection, system integration, secondary development, upper computer solution, etc. Double LC interface or other different interfaces can be tested simultaneously which is convenient for testing and improves efficiency; The VFL function could automatic on and off, no need to replace the connector.
-
product
Switch Matrices
Our standard line of switch matrices includes automated control via our command customizable controller. Interface options include USB, LAN, IEEE-488, and many other options that can customize our standard switch to meet your needs. ur existing designs cover a wide array of topologies, frequencies up to 70Ghz. and power levels from milliwatts through kilowatts.
-
product
Shelf Manager Carrier/Mezzanine Board fix-mounted for CompactPCI
064-754
Set of Shelf manager mezzanine board installed on the fix mounted carrier board. The fix mounted carrier board provides all interfaces via headers for easy access and can be used directly inside of your system platform.
-
product
Active Switching Power Supply Using Mosfet, 125 KW, P/N 5940C2
- Active Switching Power Supply Using MOSFET, 125 KW, P/N 5940C2- Input: 480 VAC, 150 Amps, 3 PH, 60 Hz- Output: 0 to 50 VDC, 2500 Amps max- Ten modules in parallel, each module is rated for 0 to 50 VDC, 300 Amps- PLC Control provides Positive Polarity, Negative Polarity and Shuts OFF- Start / Stop capability and EPO- Output voltage and current are displayed on the voltmeter and ammeter- PLC supplied by the customer. We provide a PLC interface only- Indoor enclosure dimensions: 65″W x 50″H x 36″D or (TBD)- Estimated weight: 2000 lbs. or (TBD)
-
product
Couplers, Repeaters, Bus Switches, Connectors, Cables & More
Accessories for the MIL-STD-1553 data bus are as much of an interface as the communication card. Therefore at Excalibur we provide a full line of accessories for the MIL-STD-1553 data bus that include, Box/Inline Couplers, Repeaters, Bus Switches, break out boxes, connectors, terminators, transformers and custom cable assemblies. Excalibur uses only premier quality parts from known manufacturers. We constantly test our products to meet our higher standards.If you have a need for an accessory product for your card and it is not listed please contact us to see if it is a product we should be supporting.
-
product
200-Pin LFH Connector, PCB Mount, Right Angle Female
40-963-200-RF
Accessory allows a user to create their own PCB based termination solution mounted directly on the front of the product or on the end of a cable. It is suitable for use with a variety of products. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires.
-
product
NI-9853, CAN Interface Module
780178-01
2-Port, High-Speed C Series CAN Interface Module—The NI‑9853 is a high-speed Controller Area Network (CAN) interface for developing FPGA-based applications with the NI‑RIO driver on CompactRIO. The NI‑9853 is ideal for low-level FPGA‑based control and triggering applications that are programmed using the LabVIEW FPGA Module. The NI‑9853 is ideal for byte-level manipulation of CAN frames using the LabVIEW FPGA Module. The NI‑9853 is only compatible with CompactRIO systems.
-
product
Edge Press Technology Bed of Nails Testers
Protector Edge Press Family
Designed for testing heavy massive boards. Boards with heavy components like large transformers and inductors can destroy normal test fixtures. This design utilizes a 3 plate system where an internal lever actuated sub plate containing the test pins raises to probe the circuit board when the handle is pulled. Heavy boards can bend and break exposed test pins. Similarly large boards which need to be probed by very small delicate test pins can also benefit from this protected test fixture design. This fixture is recommended in situations where there is a high board mass to pin size ratio and pin protection is required. Front and rear panel modular inserts allow for easy updates and customizations to the user hardware interface.
