-
Product
Mini Load Column Load Cell Compression Only with Mounting
MLC SERIES
-
The MLC Series is our miniature high capacity compression only load cell/force sensor, featuring low profile compact size for a wide range of portable and dedicated applications up to 30,000 lb The load diameter is slightly convex for accurate load distribution. Low deflection through design results in ultra fast frequency response. The MLCs are designed to be mounted in a shallow machined flat pocket or smooth flat surface, either free or fastened via a bottom 6-32 tapped hole. These load cells are manufactured from heat treated 17-4 ph stainless steel. The sensing element incorporates bonded foil strain gages of the highest quality and are sealed for protection against most industrial Environments.
-
Product
Torque Speed Meter
VTS-01
-
VEER make Torque Speed Meter VTS-01 is portable instrument which is very useful to find Output Power, Torque in Kgm, RPM, Corrected RPM, %Slip and Frequency of Motor. It is very simple and easy to use. It measures torque of motor from load cell & RPM from Proximity Sensor which are very useful to find output power of Motor.
-
Product
Conditioners and Transmitters
-
DIN rail mounted micro-controller based analogue load cell transmitters. They have very high accuracy and long term stability with advanced design.Using an up to-date delta-sigma ADC and 16 bit DAC to achieve higher speed and accuracy these instruments give the system designers a lot of advantages towards increasing system reliability and reducing the installation and service times. All instruments' analogue outputs are matched during production to simplify calibration with a PLC and to simplify exchanging the instrument without recalibration in service when initial adjustment has been performed in the PLC.
-
Product
Load Cells & Force Transducers
-
BLH and Nobel Weighing Systems offer a wide variety of load cells and force transducers, ranging from the unique KIS load cell and weigh module to the VPG transducers range of products. Our many years of experience, our state-of-the-art instruments, and the exceptionally broad range of components that go into our systems allow us to deliver high-quality solutions tailored to your needs.
-
Product
Load Cell DIN Rail Signal Amplifier
LCD20
-
Our intelligent strain gauge bridge amplifier is a compact, stackable microprocessor based unit specifically designed to control and monitor process applications. Flexible connection to most load cells, pressure or strain gauges over a wide range of sensitivities. The unit provides isolated current 4-20mA and voltage 0-10V analogue outputs and two digital inputs. Two set point relays can be configured to set thresholds such as net, gross, peak and valley. Powered from a wide ranging DC supply, the DIN rail amplifier is supplied with 2 part screw connectors for ease of installation.
-
Product
Compression Load Cells
-
A block that is designed to hold a load at one point to measure the compression. While tension load cells measure the pulling force, compression load cells measure a pushing force along a single axis.
-
Product
Button Load Cell
3000 Series
-
Button Load Cells are strain gage based transducers with temperature compensation and excellent overall performance. This type provides a range of capacities up to 150 kN or 30 klb with better than ±0.5% (full scale) non-linearity. Three tapped holes are provided on the underside for ease of mounting. Fully welded cover, amplified and digitised versions are available on request.
-
Product
Load Cell Tester
-
Xiamen Elane Electronics Company, Ltd
Large six-digit LED display < Easy to use and small in size < Accuracy of 0.005%FS/10ppm < 2 channels CH0 : -12mV/V~+12mV/V, with resolution 0.1uV/V CH1 : -1.6mV/V~+4.8mV/V, with resolution 0.01uV/V < Four user selectable output units (N, kgf, lbf and mv/V) < Peak Hold function to capture and holding the peak value for the immediate or later reference < Clear key to clear the peak value < Presence of tare key and foot switch to zero the display (tare function) < Great for monitoring and testing load cell characteristics (repeatability, linearity, creeping, temperature drift, etc
-
Product
Load Cell Simulator
-
A High-Stability adjustable Load Cell Simulator. It is specifically designed for Load Cell Fault and System Fault Diagnosis. It also provides a useful Development Tool for any System which relies upon Load Cells. The Output Signal is adjustable from -0.1 to +3.1 mV/V.
-
Product
Load cell simulator
PC2M
-
PC2M signal calibrator has been realised to perform periodicalchecks and calibrations on indicators with a 2mV/V input anda 4 or 6 wires systems. Provided with a main switch with 6 selectable steps, it allows to control the linearity on both positive and negative field. Internally, the 350W full bridge unbalancing, is generated by high stability passive resistances (1 ppm/C).
-
Product
Pressure-Force Cables And Connectors
-
Connectors used for pressure and force sensors. Includes cable assemblies for pressure transducers and load cells, DIN connectors, twist lock connectors, push on connectors, and dynamic sensor cables.
-
Product
TW-3.0 Data Logging Software
-
DLM TW-3.0 Data Logging Software enables PC data logging of load readings displayedon a TW-3.0 display which is connected to a TW-3.0 compatible DLM Load Cell. The applied load on the Load Cell is recorded by the software and shows a live graph against the live time and date.
-
Product
Load Cells
-
The heart of each weighing system is a load cell. Load cells are mechanical components which act as force sensors by employing strain gages to provide an electrical output proportional to the applied force. Typically the electrical output is either analog (voltage or current) or digital. Load cells have specific mechanical packaging and sensing orientation to fit into electronic scales, and testing and monitoring systems. Load cells can be used for tension, compression, and/or shear measurement.
-
Product
Beam Load Cell
EST-70
-
Technopark Automation & Control
The EST-70 Shear Beam Load Cell is commonly used on platform, hopper weighing and pallet weighing applications. It is low cost and available in capacities from 500 kg to 2000 kg.
-
Product
Digital Load Calibrator
HS 2000
-
Jinan Testing Equipment IE Corporation
The load cell calibrator is used to calibrate the load of testing machine and hardness tester, and also can be used for force measuring. It is digital display type with high accuracy of less than +0.3%, and easy to operate
-
Product
Force Transmitter
LKVE/i
-
The PIAB LKVE electronic overload protection system consists of a force transmitter with amplifier and an electronic signal processing unit. The PIAB LKVE force transmitter is attached to a stationary line part. The rope is deflected via a slight angle between the two wheels and the clamping jaw. When loaded, the rope tends to straighten and applies a force which is transmitted to the load cell. The load cell in the PIAB LKVE delivers a signal proportional to the force on the load cell. The signal is amplified and is converted to 4-20mA. This standardized signal (4-20mA) allows distances between the force transmitter and the electronic unit to be 500 m.
-
Product
Through Hole/ Donut Load Cell Compression Only
THA SERIES
-
Our THA Series through hole donut load cells offer an outside diameter of 1.00 inches and up to two different through hole diameter options per capacity range. These load cells are manufactured from heat treated 17-4 ph stainless steel. The sensing element incorporates bonded foil strain gages of the highest quality and are sealed for protection against most industrial environments.
-
Product
In Line Load Cell (10KN-50KN)
106, 107, 108 Series
-
Miniature Threaded in Line Load Cells are strain gage based transducers with temperature compensation and excellent overall performance. This type measures tensile and compressive loads up to 50kN and 10klb with better than ±0.5% non-linearity. This type is also available with fully welded cover.
-
Product
High Speed Load Cell Test Interface
LCIC-4CH
-
Industrial Measurement Systems Ltd.
The latest stand-alone controller model: LCIC-4CH, was specially designed to fit portable wheel and axle scales for determining the weight of trucks or heavy vehicles either in static mode or in motion, with very high accuracy and very friendly to operate. The In-motion speeds up the weighing process and allows weighing a truck without the need to stop.In the last 16 years, our stand-alone High-Speed weighing-in-motion controller model: LCIC-WIM was sold all around the world and as for today, thousands are being in use when among our customers are some well known weighing manufacturers.Most of our customers around the world are scale manufacturers or integrators that were able to offer the market the most advanced WIM scale with very short time to market and minimum R&D expenses.
-
Product
Digital Motorized BRINELL Hardness Tester
900-355
-
Load Cell driven system provides precise control of test force application Direct digital reading Engineered to obtain highly sensitive and accurate readings Perfect for laboratories, workshops, tool rooms, inspection labs, etc. Measuring Range: 8-650HBW
-
Product
load cell
EST-40
-
Technopark Automation & Control
The EST-40 is an 'S' type load cell suitable for use in tension and compression and is popular on hopper, tank weighing, belts scale and process weighing applications. It is low cost and is available in capacities from 50 kg to 2000 kg.
-
Product
Force Sensors
-
The Force Sensors segment includes a broad line of load cells and force measurement transducers that are offered as precision sensors for industrial and commercial use. Typical applications for force sensors are in medical devices (such as hospital beds and medication dosing), agricultural equipment (for precision force measurement), and construction machinery (for tipping and overload protection). These sensors use our foil technology products, which serve as sensing elements and components within each unit. Further integration of our load cells technology is also offered as part of our weighing module products, which provide customers with a complete sensor assembly that may be used within a wide variety of digital transducers.
-
Product
Single Point Load Cells
-
These have a range of different platform sizes and are suitable for different applications including bench scales, counting scales and other applications in many industries. Click the links below to find out more about each product and to view specific data sheets.
-
-
Product
Load Cell Transmitter
MODEL SST-LV
-
The SST-LV is a Plug & Play Smart TEDS IEEE 1451.4 compliant Transmitter. Just plug in a TEDS compatible Load Cell or Torque Sensor and the SST-LV will automatically self-calibrate. When used with a non-TEDS Load Cell or Torque Sensor, the SST-LV Transmitter is easily programmed using a PC with an RS232 port and Instrument Setup (IS) software, which provides a graphical user interface. The SST-LV may be powered from 12-30 Vac or 10-48 Vdc. The SST-HV Has an Isolated transducer excitation output that is selectable between 5Vdc or 10Vdc. There are Dual solid state relays and an Isolated 4-20 mA, 0-20 mA or 0-10V analog output. There are three Isolated serial data transmitter output ( RS232 , Half-duplex RS485, full-duplex RS485 ) and three serial protocols that are software selectable (Modbus RTU, Modbus ASCII and Custom ASCII). Isolation to 250V rms is provided for power, signal input, analog output, relay outputs, and communications. Isolation adds safety and avoids possible ground loops. The transducer excitation output is isolated to 50V from signal ground.
-
Product
Load Button Load Cells
-
Interface’s load button load cells are designed for customers who require the measurement of compression forces in a very low height space. They are designed to provide the most accuracy in as little space as possible. The smaller ConvexBT or LBMU can fulfill the need for force measurements at a very respectable precision level that is enough for most applications. Diameters range from ⅜ of an inch to just over 3 inches, with heights from ⅛ of an inch to 2 inches. The shaped load button has a spherical radius to help confine misaligned loads to the primary axis of the cell.
-
Product
16-Station Testing System
-
The ElectroPuls 16-Station testing system performs high cycle fatigue testing on multiple samples simultaneously, with a fatigue-rated load cell included on each station. The fixture uses a carousel designed with high stiffness and low mass to enable high frequency testing and reduce test time.
-
Product
(2500kN+) Fatigue Testing Systems
8806
-
The precision mechanical systems, combined with the advanced features of the 8800 digital controller and Dynacell™ load cells, enable Instron to supply fully-integrated turnkey solutions to meet the most demanding applications. The system can be used to cover a broad range of static and dynamic test applications, covering metals, rebar, high-force fracture mechanics, aerospace panels, civil engineering components, wire ropes, or concrete.
-
Product
DMS Transmitter
-
Knick Elektronische Messgeräte GmbH & Co. KG.
Transmitter for load cells and the evaluation of strain gages in 6 mm housing with calibrated range selection.Detection signals from sensors for physical variables such as displacement, angle, pressure or force. Functional safety up to SIL 2, SIL 3 redundant to parameterization via interface or intuitively, directly on the device. Universal use with 24 V DC or AC power supply.
-
Product
Load Cell Electronics
-
All our electronics are continuously evolving to feature faster and more powerful components. This commitment to innovation ensures that we can meet any new challenge or application.
