-
Product
In Line Load Cell (200N-5000N)
100 Series
-
Miniature Threaded in Line Load Cells are strain gage based transducers with temperature compensation and excellent overall performance. This type measures tensile and compressive loads up to 5000N with better than ±0.25% non-linearity.
-
Product
TW-3.0 Multi Logger Software
-
The TW-3.0 Multi Logger Software from DLM is designed to complement DLM’s TW-3.0-Trange of products. It is used for monitoring and logging data for up to 24 TW-3.0-T LoadCells including Wireless Compressive Load Cells, Telemetry Tensile Links, and TelemetryLoad Shackles.
-
Product
Hopper Weigher
-
This weigher can be easily installed in a hopper for faster construction by adopting our prominent load cells with built-in constrainer.
-
Product
Single Point Aluminium Load Cell
EST-4
-
Technopark Automation & Control
The EST-4 is a Single Point Aluminium Load Cell suitable for use on platform scales measuring 1200 x 1200 mm. This load cell is available in capacities 1000 kg and 2000 kg.
-
Product
NI-9237, 50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module
780264-02
Strain/Bridge Input Module
50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module - The NI‑9237 includes all the signal conditioning required to power and measure up to four bridge-based sensors simultaneously. The module provides strain or load measurements with zero interchannel phase delay. It also has 60 VDC isolation and 1,000 Vrms transient isolation, providing high‑common‑mode noise rejection and increased safety. You can program the NI‑9237 for use with half-bridge and full-bridge sensors with built-in excitation. The four RJ50 jacks provide direct connectivity to most torque or load cells and offer custom cable solutions with minimal tools.
-
Product
TW-3.0 Data Logging Software
-
DLM TW-3.0 Data Logging Software enables PC data logging of load readings displayedon a TW-3.0 display which is connected to a TW-3.0 compatible DLM Load Cell. The applied load on the Load Cell is recorded by the software and shows a live graph against the live time and date.
-
Product
Canister Load Cell
-
Futek Advanced Sensor Technology, Inc.
FUTEK provides a wide range of Canister Load Cells designed for high capacity compression applications. These models offer robust construction with a capacity range beginning
-
Product
Load Cell Amplifiers
-
Datum Electronics load cell amplifier range is designed to increase (or amplify) a signal, generated by a strain gauge load cells with a full bridge connection, pressure transducers or torque sensors, allowing the user to use the data from the load cell in a more efficient and productive way.
-
Product
Pressure-Force Cables And Connectors
-
Connectors used for pressure and force sensors. Includes cable assemblies for pressure transducers and load cells, DIN connectors, twist lock connectors, push on connectors, and dynamic sensor cables.
-
Product
Force & Strain Measurement
-
Load cells, tank weighing devices, balances, scales, force gauges, torque sensors and strain gauges including diaphragm, dual parallel, linear, rosette, T-rosette, and torsion and shear types.
-
-
Product
Thru Hole Donut Load Cell
-
Futek Advanced Sensor Technology, Inc.
The Thru Hole Donut Load Cell Series offers 5 models built for Off-Center Loading, Press, or Inline compression applications. These models have a very robust construction available in 17-4 Stainless Steel, with an I.D. range of 1/8" to 1 1/4".
-
Product
Load Cell Measurement Interface
LCIC-1106a
-
Industrial Measurement Systems Ltd.
Any application related to weighing or measuring forces is now available in your PC...Stand-alone microcomputer-based interface card requires no other interfacing accessories. Simply connect th
-
Product
Load Cell Indicator
9840
-
The 9840 is suitable for use in calibration labs, field service, or anywhere high accuracy is important. Features include a bipolar 6-digit 2-line display, remote sense, low noise, 22-bit resolution, USB port with RS232 communication, mV/V calibration and the ability to store up to 25 different sensors. 6-point linearization, unit conversion, front-panel tare. Self calibration via TEDS Plug & Play ready IEEE1451.4 compliance.
-
Product
Tensile Compression Force Tester
ESM303
-
The ESM303 is a highly configurable single-column force tester for tension and compression measurement applications up to 300 lbF [1.5 kN], with a rugged design suitable for laboratory and production environments. Sample setup and fine positioning are a breeze with available FollowMeTM force-based positioning - using your hand as your guide, push and pull on the force gauge or load cell to move the crosshead at a variable rate of speed.
-
Product
500 N Screw Flat Grips
-
500 N (110 lbf) screw flat grips are for use with low-capacity AGS-X series and EZ-X series load cells and come with flat grip faces. Similar to standard screw flat grips, these grips are versatile and are used for static tensile testing a wide range of materials, including rubbers, plastics, textiles, cloth, and paper, in film form.
-
Product
Force Sensor Elements
-
The STL Force Sensing Tension Links are a series of unique force sensors. The Tension Links utilize the internal strain gage process sucessfully and are used in bolts, load pins and flat load cells. The sensing element consists of a strain gage bridge circuit internally installed in a small hole along the longitudinal axis. This unique arrangement provides a most effective means for the protective sealing of the internal electronics while minimizing the adverse effects of extraneous torsion and bending loads.
-
Product
NI-9219, 100 S/s/channel, 4-Channel C Series Universal Analog Input Module
779781-02
Analog Input Module
100 S/s/channel, 4-Channel C Series Universal Analog Input Module - The NI‑9219 is designed for multipurpose testing. With the NI‑9219, you can measure signals from sensors such as strain gages, resistance temperature detectors (RTDs), thermocouples, load cells, and other powered sensors, as well as make quarter-bridge, half-bridge, and full-bridge current measurements, with built-in voltage and current excitation. Each channel is individually selectable, so you can perform a different measurement type on each channel.
-
Product
Remote Displays
HS Series
-
Load cell / scale remote displays are driven from another digital indicator or amplifier. Often used on bridge cranes and truck scales, or in any situation which the person needing to see the scales displayed weight is too far to see the smaller standard indicators. Many styles, digit sizes, indoor and outdoor models are available.
-
Product
Load Cell Amplifier Signal Conditioner with DB9 Connectors
MODEL LCA-9PC
-
The LCA-9PC Module provides low-cost, dedicated signal conditioning for a single bridge type load cell or torque sensor. Model LCA-9PC comes with DB9 male and female connectors, which require soldering to user-furnished mating female or male wire connectors. On- board jumper selections include sensitivities from 0.5 mV/V to 10 mV/V, bandwidths from 100 Hz to 30 kHz, and amplified outputs of 0 to ±5V, 0 to ±10V, 0-16 mA, 0-20 mA or 4-20 mA. Zero and span adjustments are via precision 25-turn low-tempco metal film otentiometers.The units can be operated next to the sensor with 4-wire hookup or at distances up to 1 km (3300 feet) with 6-wire hookup. An onboard 87.325 kΩ resistor allows easy shunt calibration at the push of a button. Provision is also made for a user-furnished calibration resistor. Power requirements are 11.8 to 26V DC with load currents from 10 to 60 mA, the latter applying when the unit provides 10V DC excitation to a 350 ohm load cell and delivers a 20 mA analog output.
-
Product
10 N Screw Flat Grips
-
10 N (2.2 lbf) screw flat grips are primarily used for tensile testing low force, soft materials such as yarn, paper, plastics, and cloth, in film or wire geometry. Grip faces are flat and rubber-coated, and the supplied coupling joints for the 10 N screw flat grips are designed for use on lower-capacity load cells.
-
Product
Single Point Aluminium Load Cell
EST-5
-
Technopark Automation & Control
The EST-5 is a Single Point Aluminium Load Cell suitable for use on platform scales measuring 600 x 600 mm. This load cell is available in capacities 50 kg and 100 kg.
-
Product
sbRIO-9237, Non-Enclosed, 50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module
781028-01
Strain/Bridge Input Module
Non-Enclosed, 50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module - The sbRIO‑9237 includes all the signal conditioning required to power and measure up to four bridge-based sensors simultaneously. The module provides strain or load measurements with zero interchannel phase delay. It also has 60 VDC isolation and 1,000 Vrms transient isolation, providing high‑common‑mode noise rejection and increased safety. You can program the sbRIO‑9237 for use with half-bridge and full-bridge sensors with built-in excitation. The four RJ50 jacks provide direct connectivity to most torque or load cells and offer custom cable solutions with minimal tools. Non-enclosed modules are designed for OEM applications.
-
Product
Versatile 5-Channel Industrial Amplifier/ Conditioner Instrument
MODEL TIO-3000
-
The TIO-3000 System was originally designed to perform precision summing on 2, 3 , or 4 load cell signals for weighing applications. Development has progressed into accessory modules with considerable versatility for user defined configurations in a compact economical five (5) slot system with built-in meter and channel selector. Please see below for more information on the four available plug in modules and for available system configurations.
-
Product
Load Cells, Weighing and Force Sensors
-
We are pleased to offer Load Cells from both Zemic and Vishay. We are the exclusive UK distributor for Zemic load cells.
-
Product
Signal Conditioning and Filtering
MSXB 067
-
The MSXB 067 Signal Conditioning Expansion Board provides analog signal conditioning for strain gauges, load cells, RTDs, and other resistive sensors. MSXB 067 provides a flexible interface for quarter-bridge, half-bridge, and full-bridge sensors, with two to six wires for each sensor, with or without voltage sense feedback. A small daughterboard supports user-supplied bridge completion resistors.
-
Product
Load Cell Transmitter
MODEL SST-HV
-
The SST-HV is a Plug & Play Smart TEDS IEEE 1451.4 compliant Transmitter. Just plug in a TEDS compatible Load Cell or Torque Sensor and the SST-HV will automatically self-calibrate. When used with a non-TEDS Load Cell or Torque Sensor, the SST-LV Transmitter is easily programmed using a PC with an RS232 port and Instrument Setup (IS) software, which provides a graphical user interface. The SST-HV may be powered from 95-240 Vac ±10%. The SST-HV has an Isolated transducer excitation output that is selectable between 5Vdc or 10Vdc. There are Dual solid state relays and an Isolated 4-20 mA, 0-20 mA or 0-10V analog output. There are three Isolated serial data transmitter output ( RS232 , Half-duplex RS485, full-duplex RS485 ) and three serial protocols that are software selectable (Modbus RTU, Modbus ASCII and Custom ASCII). Isolation to 250V rms is provided for power, signal input, analog output, relay outputs, and communications. Isolation adds safety and avoids possible ground loops. The transducer excitation output is isolated to 50V from signal ground.
-
Product
Digital Load Cell Simulator
Model EL41
-
Xiamen Elane Electronics Company, Ltd
Detection and debugging of all kinds of weighing instruments - "must have" for any scale service technician - fully RS232 controllable for testing of electronics for scale installation and manufacturing.
-
Product
Force Sensor Elements
-
TE Connectivity (TE) enables OEMs to measure force using MEMS-based technology load cells. The same proprietary piezoresistive silicon strain gage technology used to measure pressure can also be configured into a reliable, low-cost package to measure force.
-
Product
NI-9237, 50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module
780264-01
Strain/Bridge Input Module
50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module - The NI‑9237 includes all the signal conditioning required to power and measure up to four bridge-based sensors simultaneously. The module provides strain or load measurements with zero interchannel phase delay. It also has 60 VDC isolation and 1,000 Vrms transient isolation, providing high‑common‑mode noise rejection and increased safety. You can program the NI‑9237 for use with half-bridge and full-bridge sensors with built-in excitation. The four RJ50 jacks provide direct connectivity to most torque or load cells and offer custom cable solutions with minimal tools.
