Test Fixtures
UUT interconnect interchangeable with tester.
See Also: Fixtures, Mechanical Fixtures, Vacuum Fixtures, ATE Fixtures, PCB Test Fixtures, Board Test Fixtures, Bed of Nails, Spring Probes, Test Jigs, Test Probes
-
product
Functional Test
cUTS
Get the essentials of measurement automation to power tests of simpler PCBAs and subassemblies. compactUTS (cUTS) is a cost-effective platform for automating manual tests of devices with fewer than fifty cable-accessible test points in manufacturing environments with moderate production volume. DUT-specific electrically keyed cables make changeover quick and easy.
-
product
VXI Digital Test Instrument
T940 Series
The T940 Series for the VXIbus provides the basis for a complete state-of-the-art digital solution at the subsystem level. The T940 is the solution for both legacy digital replacement and new test stations to be built for digital test including aircraft/ avionics, weapons systems, spacecraft, semiconductors and medical devices.
-
product
NI Vehicle Radar Test System
VRTS provides automated radar measurement and obstacle simulation capabilities for 76 to 81 GHz automotive radar systems. With VRTS, you can perform precision RF measurements and simulate a wide range of test scenarios for radar hardware and software subsystems, including sensors, advanced driver assistance systems (ADAS), and embedded software. Use VRTS for all phases, from design to manufacturing, of ADAS and radar system test.
-
product
Bluetooth RF Test System
FRVS
FRVS is recognized by the Bluetooth SIG as a validated test system for qualification testing of products to Bluetooth BR/EDR and low energy RF test specifications.
-
product
Seno-Con Test System
PANTHER 2K QST
Qmax Test Technologies Pvt. Ltd.
Panther 2K-QST is a versatile ultra fast Seno-Con test system designed to test high volume ,low to high pin count consumer semiconductor IC’s for its assembly line wire bonding faults. Its innovative test technology helps learn from known good device and test against target device drastically reduces time required to develop Test programs.The operating software is designed in such a way that it is fully user friendly with GUI programming.
-
product
Standalone Bench Test System for FCT, ICT, ISP and Boundary Scan
LEON Bench
The LEONBench test system is a flexible and scalable test system that features an excellent signal integrity and a high-quality fixture interface. This is achieved by combining a cableless connection from ABex modules to Virginia panel interface connectors. The system is optimized for high pin count test applications. Furthermore, it can be equipped with vacuum and pneumatic. Support for multi-level contact fixtures enables separate contact levels for FCT and ICT. The Konrad ITA (Interchangeable Test Adapter) frame allows various fixture houses all over the world to build custom fixtures for the LEONBench. Up to 15U additional rack space allows adding a bunch of high-performance measurement devices from various manufactures. An integrated power distribution unit takes care about power on and off sequencing.As part of the LEON Family, LEONBench is based on the ABex platform which directly incorporates Konrad analog bus technology and PXI/PXIe in one chassis.
-
product
TestStand
TestStand is industry-standard test management software that helps test and validation engineers build and deploy automated test systems faster. TestStand includes a ready-to-run test sequence engine that supports multiple test code languages, flexible result reporting, and parallel/multithreaded test.
-
product
Fully-Automated CTIA-Compliant OTA Test System
TS8991
The R&S®TS8991 OTA performance test system measures the spatial radiation and sensitivity characteristic as specified by CTIA and 3GPP.The system software provides ready-to-use test templates for OTA measurements and supports all wireless standards.The integrated report function collects all measured test data such as graphics or numeric results, test environments, EUT information and hardware setup in one document.
-
product
OTP-Based Test System
Power electronics assemblies often cannot be tested using conventional technology for their electrical performance. Due to the adaptability of the instrumentation, the OTP concept offers an ideal platform even beyond the space requirements of several control cabinets. In order to achieve high test flexibility with different assemblies, the system was equipped with three-phase AC sources and AC loads as well as a precise three-phase power meter. DC sources and loads with different current and voltage ranges cover the test of frequent DUT operating parameters. Time-dependent voltage or current signals can be stimulated by an arbitrary generator with power amplifier. General measurements such as current, voltage, frequency, resistance can be carried out flexibly at various test points using the matrix concept. An oscilloscope with RF multiplexer is available for high-frequency measurements such as residual ripple, switching processes, etc.
-
product
HV Test System up to 20000 Volt
Insulated test booth with large space for test items. 2 banana sockets for AC connection and 4 banana sockets for the DC connection of the DUTs. IC’s are tested in a long-term test. These are checked in an oil bath so that there are no air gaps to reduce the insulation. Maximum voltage 20 kV. Therefore, insulation tests must be carried out. Ensuring the standard-compliant test. For the safety of the operating personnel, the test cell is electrically locked while the high voltage measurement is active.
-
product
Positioning Test System
TS-LBS
The R&S®TS-LBS is a comprehensive test solution for network and satellite based location technology testing of wireless devices and chipsets.It is highly configurable for testing various location technologies and uses Rohde & Schwarz location based test systems.The R&S®TS-LBS test system family fulfills the requirements of LBS conformance testing and operator acceptance testing on GSM, WCDMA, LTE and 5G devices and chipsets as well as regulatory testing consisting of adjacent channels and spurious emissions for EN 303 413 receiver testing. It also fulfills the requirements of E112 (EU) 2019/320 testing consisting of GNSS testing such as Galileo and AML mobile testing.
-
product
SoC Test Systems
SoC (System on Chip) devices integrate multiple different functions into a single chip. Our SoC test systems can test all the integrated circuits in SoC devices, including logic, analog, RF, DC and imagers by flexible configuration of the cards/modules used in the test system.
-
product
Optimize Throughput And Cost For MmWave 5G Device Functional Test
Test engineers always have faced tough new test-coverage challenges. Those introduced by 5G measurements at mmWave are no exception, as they require over-the-air (OTA) radiated test solutions. But never have these pressures seen today’s intense time-to-market, manufacturing volume, and operational expectations! A solution that meets these demands must:
-
product
PXI Semiconductor/IC Test System
A high-density 100MHz PXIe digital IO card designed for characterizing, validating, and testing a variety of digital and mixed-signal ICs. Each IO card consists of a Sequencer Pattern Generator (SQPG) and 32 channels of full ATE-like features. The 33010 IO card is expandable up to 256 channels. Some unique features of the 33010 include an on-board SQPG, per pin timing/levels/ PMU/TFMU, multiple time domains, and multithreaded testing for complex IC testing. Each channel is also equipped with 64M vector memory, 16 timing sets with on-the-fly timing change, and per pin timing and frequency measurements up to 400 MHz.
-
product
VR/AR/MR Calibration Platform
AR, VR and MR device calibration is critical for product performance. Leverage Averna’s standardized alignment platform to efficiently calibrate cameras and Inertial Measurement Unit (IMU) modules with supreme accuracy. Easily customize or upgrade the base platform into the automated quality solution to best fit your manufacturing requirements.
-
product
Test System
BMS HIL
The BMS Hardware-in-the-Loop (HIL) Test System is a high performance platform providing all necessary input signals used for battery pack simulation. A real-time operating system executes complex cell and pack models commonly used for BMS algorithm development and firmware regression testing.
-
product
Application Software for Electronic Test & Instrumentation
Application software provides configuration-based workflows for electronic test and instrumentation applications. Application software is part of the NI software portfolio.
-
product
In-line High-Density ICT System Series 7i
E9988GL
The E9988GL Keysight i3070 Series 7i Inline High-Density In-Circuit Test (ICT) system brings industry-leading ICT technologies into your automated manufacturing line, saving resources and optimizing your automated test strategy.
-
product
Regenerative Battery Pack Test System
17040
Conforms to international standards for battery testing: IEC, ISO, UL, and GB/T, etc.Regenerative battery energy discharge (Eff. >90%, PF >0.95, I_THD <5%)Multiple voltage and current ranges for auto ranging function to provide optimum resolutionHigh accuracy current/voltage measurement (0.05%FS/0.02%FS)2ms current slew rate (-90% ~ 90%)Dynamic (current/power) driving profile simulation tests for NEDC, FUDS, HPPCTest channel parallel functionTest data analysis functionData recovery protection (after power failure)Automatic protection for error conditionBattery simulator (option)High power testing equipment- Voltage range : 80~1000V - Current range : 0~750A - Power range : 0~300kWCustomized integration functions- Integrated temperature chamber - BMS data analysis - Multi-channel voltage/temperature recording
-
product
Mini In-Circuit Test System
U9403A
The Keysight Mini ICT is a true in-circuit test unit in the rack that can be used standalone or integrated. It comes with a full set of Keysight ICT test features, from VTEP vectorless test, Cover-Extend Technology, to digital library tests and boundary scan. The unmuxed per-pin programmable digital engine makes test development really flexible and easy, especially in a situation when device conditioning is needed in functional test.
-
product
PCI Express 3.0 Test Platform with SMBus Support
The Summit Z3-16 Test Platform with SMBus Support allows the Summit Z3-16 to act as a host emulator, and provides a general purpose test backplane and interposer for testing Gen3, Gen2 or Gen1 hosts and devices. In addition, it supports the Summit Z3-16 with SMBus Support by providing SMBus tapping connectivity.
-
product
Modular Functional Test Platform
LX-OTP2
The OTP² system platform has recently been available in both the PXI and LXI versions. The OTP2 system platform enables the cost-effective and fast implementation of function test systems based on defined modules and function blocks. Thanks to the open system interfaces, customer-specific adjustments can be made at any time without any problems. When considering options for your next generation functional test system, it is important to assess the entire life cycle of the system and the associated costs and efforts. Use OTP² to accelerate development cycles and reduce the development effort for new functional test systems.
-
product
NTS Platform
Manufacturers all over the world are leveraging our NTS platform for products with rotating or otherwise moving parts, or produce sounds. Typical applications include mass production of air conditioning units, pumps or small electric motors, where errors in assembly can cause malfunctions or significantly shorten service life. This test platform is customized to your specification and application. Feasibility studies are available to ensure your solution is exactly what you are looking for.
-
product
Mach Airspeed Test Fixture
TA-6055A
The TA-6055A is a Mach Airspeed Test Fixture built to support the testing and repair of the 2082 and 2083 series of Servoed Mach Airspeed Indicators (SMASI) used in some Boeing aircraft. These mach airspeeds are synchro driven and require a coarse and fine input for altitude and a third input for airspeed. This test fixture was designed around the test procedure and is interfaced with our TA-1001 panel which provides for two of the synchro sources and two Angle Position Indicators (API).
-
product
Scienlab Battery Test System - Cell Level
SL1007A
The SL1007A Scienlab Battery Test System – Cell Level enables you to accurately and productively test battery cells for automotive and industrial applications. The bidirectional power supply charges and discharges your cells under test with very high efficiency.
-
product
VLSI Test Systems
50/100 MHz clock rate50/100 Mbps data rate1024 I/O pins (Max :1280 I/O pins)Up to 1024 sites Parallel testing32/64 M pattern memoryVarious VI sourceFlexible HW-architecture (Interchangeable I/O, VI, ADDA,)Real parallel trim/match functionTime & frequency measurement unit (TFMU)High-speed time measurement unit (HSTMU)AD/DA test optionSCAN test option (max 1G M/chain)ALPG test option for embedded memorySTDF tools supportTest program/pattern converter(J750, D10, V50, E320, SC312, V7, TRI-6020, ITS9K)User friendly windows 7 environmentCRAFT C/C++ programming languageSW (Software) same as 3380P & 3360P
-
product
Ethernet and Fibre Channel Test Platform
SierraNet M1288
The SierraNet M1288 Ethernet and Fibre Channel test platform provides best in class analysis, jamming and generation for traffic capture and manipulation for testing application and link characteristics. SierraNet M1288 is the latest in the line of industry leading test and measurement tools from Teledyne LeCroy, designed for today’s high-speed storage and communications fabrics. SierraNet M1288 supports examination and modification of Ethernet and Fibre Channel links utilizing both Pulse Amplitude Modulation 4 (PAM4) and legacy Non-Return to Zero (NRZ) technologies.
-
product
Test System Optimized for High-Performance Digital and SoC
ULTRAWAVEMX44 and ULTRAWAVEMX20-D16
Teradyne is the leader in RF/wireless device testing and has a large installed base of UltraFLEX test systems with the UltraWave24 RF instrument. As new devices for handset and base station applications are introduced using mmWave technology, Teradyne’s mmWave instrumentation has expanded in anticipation of new testing demands.
-
product
RF Testing Platform for ATx05
AT118
The functional test of modern devices with wireless connectivity always requires RF isolated cameras, as the only way to have the parameters controlled and to guarantee operation under the specified conditions.
-
product
Test Systems
Ball Systems delivers best-in-class automated testing systems, software programming, integrated manufacturing systems, and industrial engineered solutions. Our team has former corporate test engineers, quality assurance engineers, industrial engineers, and test managers who have decades of experience to assist customers in meeting their automated test challenges by offering:
