-
Product
Fiber Extender Kit
L-1SDI-FE-3G-TX/RX
-
The L-1SDI-FE-3G-TX/RX is a SD/HD/3G-SDI over fiber transmitter and receiver extender kit. This unit provides optical transmission of one SD/HD/3G-SDI signal with embedded audio signal and has reversed RS485 data channel for camera control. L-1SDI-FE-3G-TX/RX kit can be used in HD video conference, as well as HD video monitoring, intelligent transportation system and public security system.
-
Product
Solar Radiation Sensors & Transmitters
A70 Series
-
The Comptus A70 Series solar radiation sensors with transmitters are available in two models. The A70-A PAR Sensor measures photosynthetically active radiation (PAR) in the 400 to 700 nm range. The A70-I Insolation Sensor measures solar radiation in the 280 to 2800 nm range. The signals from the sensors are scaled by the signal conditioner to provide the desired output.
-
Product
CATV Fiber Optic 1550nm Transmitter
T8500HC Series
-
The MX-T8500HC series externally modulated transmitter delivers high performance signal transmission of NTSC, PAL, digital or compressed digital signals from 50-862 MHz for CATV applications.
-
Product
PC Programmable, Suitable For Pt100 Sensors
SEM206P
-
The SEM206/P is our entry level PC programmable temperature transmitter. It accepts Pt100 temperature sensors and converts the sensor output to a standard industrial (4 to 20) mA transmission signal.
-
Product
SAR Testing
-
RF transmitters used in close proximity to the human body must be evaluated against human Exposure standards which set basic restrictions for the Specific Absorption Rate (SAR) of RF energy by any part of the human body. This may include two-way radios, cellular phones, smartphones, spread spectrum, Bluetooth devices, wireless EFTPOS terminals and WLAN devices used in PDA/notebook/laptop/tablet computers. In Australia and Europe, virtually all devices exceeding the power threshold of 20mW (13dBm) and used in close proximity to the human body must comply with SAR requirements. There is no such blanket exemption in the USA and Canada where each product must be assessed against frequency/power level criteria.
-
Product
Temperature Transmitter
T4111
-
Transducer is designed for temperature measurement at C or F by means of an externaltemperature probe with Pt1000 sensor. Measured temperature is converted to linearized unified signal 4-20 mA. Measured values are displayed on LCD display. It is possible to switch OFF theLCD at all. Current loop has two-wire connection and requires power from evaluation device.
-
Product
Ethernet Tester
ProPlex IQ
-
Ethernet tester for entertainment production applications. Designed with input from production and staging professionals as an all-in-one device, it provides feedback and analysis on any Ethernet protocol, as well as network troubleshooting. It can act as a DMX cable tester, DMX receiver/transmitter, DMX timing analyzer, DMX recorder, RDM controller, or a bidirectional Ethernet-DMX gateway. It is also a PoE tester that can determine the capabilities of any connected PoE source. Finally, it can check SMPTE timecode or act as an LTC receiver/analyzer, and LTC transmitter, and users can use it to update Solaris/ProPlex firmware without a PC.
-
Product
Lightwave Transmitter Analyzer Bundle
N4364A
-
The N4364A Lightwave Transmitter Analyzer Bundle consists of a calibrated OE-converter - the N4377A Lightwave Detector - and Vector Network Analyzer - either from the PNA- or from the Streamline Series USB-family - and is a cost-effective solution to test the frequency response of optical transmitters such as directly modulated lasers diodes (DMLs), Mach-Zehnder Modulators (MZMs) or other devices.
-
Product
Universal Checkback Standalone System
UCBS
-
The Universal Checkback Standalone System (UCBS) provides periodic testing of "ON-OFF" carrier sets other than the TC-10B and the UPLC/UPLC-II (which incorporate this same checkback tester internally). The UCBS determines the functionality of the complete channel including the transmitters, receivers and associated coupling equipment. Periodic testing is required for the normally "off" channel, to provide warning of signal deterioration prior to needing it for relaying, The UCBS facilitates automatic testing of the channel at preset intervals. The UCBS is totally field programmable. All programming is done with a computer using the RS232 serial port or limited factory settings with switches on the Checkback module. Front panel LEDs indicate the factory or custom setting applied and the status of alarms.
-
Product
Oxygen Transmitter
Model InstaTrans-XD
-
Teledyne Analytical Instruments
This model utilizes a design to meet the requirements of NEMA-4(IP-66) levels as well as ATEX Zone 0/1/2 and FM/FMc Class I Div 1 approvals when used with select intrinsic safety barriers. In addition, the CSA approval extends to Class I Div 2 as a non-incentive device without the use of barriers. The transmitter head contains the electronics and user display interface including 4-button design to access functions.
-
Product
Transmitter or Receiver Testboards
-
VI Systems offers parallel optic testboards for 4 channel x 25 Gbit/s and 12 channel x 25 Gbit/s applications and product development.
-
Product
Chilled Mirror Transmitter
DewTrak II
-
The DewTrak II uses the chilled mirror dew point temperature condensation principle to determine the water vapor concentration in gas mixtures, and a platinum resistance thermometer to accurately measure that temperature. Outputs include 4 to 20mA, 0 to 5 Vdc, or 0-10Vdc and an RS232 serial port as well as electrically isolated relay contacts.
-
Product
RF Mixers & Frequency Converters Overview
-
Up and down conversion is often used because waveform generation in a transmitter is less expensive at lower frequencies and the dynamic range of analogue-to-digital converters in the receiver is higher at lower frequency.
-
-
Product
Gauges and Transmitters
-
Meriam offers a wide variety of mechanical and digital pressure gauges for process measurement and indication. Terrific accuracy specifications and little-to-no temperature effect set these instruments apart from the competition. Many of our digital gauge products have multiple output options to increase their versatility in today's changing control schemes. Mechanical gauges have been the reliable standard in pressure measurement and still have their place in today's industrial environment. They excel in areas where digital units cannot function, such as in very cold installations.
-
Product
Standard Mechanical Calibration Kit, DC To 7.5 GHz, 7–16 (male)
85038M
-
Modern wireless communication systems require high-performance components offering low VSWR and low intermodulation distortion at high transmit power levels. To meet these needs, 7-16 connectors are becoming increasingly common in base station transmitters, amplifiers, duplexers, and other products. These connectors conform to IEC 169-4, DIN 47223, European standard EN 122190, and British standard BSEN 122190.
-
Product
Terminal Power Meter
TPM-50A
-
ShinewayTech@ TPM-50A Terminal Power meter can test (1) Average power range: -40 dBm~+20 dBm；(3) Modulation bandwidth: 5MHz；(3) Continuous signal and burst signal test. Highly accurate power measurement CW and digital modulated signal (For example: GSM/EDGE, CDMA/EV-DO, WCDMA/HSDPA, WiMAX, and TD-SCDMA). It is very important to test that if the transmitter is at a specified level or not. For example, the tester needs to test the output power of base station. Because the lower output power produces the larger coverage area to cause call interruption.
-
-
Product
Cable Detectors
-
The cable detector makes it easier to find cables in the wall and cable ducts. Here, an adapter or carrier signal from the transmitter is modulated by means of crocodile clips or the adapter to one end of the cable. The other end of the cable can then be found quickly and precisely with the receiver without contact or having to strip the cable insulation. Two-core cables can also be exactly identified in telecommunication and network technology.
-
Product
Meteo Barometric Transmitter
HD9408T… Series
-
Barometric transmitter output 0…1 Vdc, measuring range 800…1100 mbar. (600…1100 on request).
-
Product
Sanitary Magnostrictive Level Transmitter
DM330S
-
The Drexelbrook DM330S is a sanitary magnetostrictive level transmitter providing Triclover fittings as standard mountings. It is authorized by 3A Sanitary Standards Council for level applications in the food and beverage industries.The DM330S takes field proven sensing technology and incorporates intrinsic safety with a field programmable zero and span.The two wire loop powered level transmitter is configurable with a 4-20 mA span and is not affected by changes in electrical characteristics.It uses proven machine tool positioning accuracy combined with a process compatible float to offer a liquid level, and interface measurement system for the process industry.
-
Product
Pressure Transmitters
-
Explosion-proof pressure transmitter is approved for use in hazardous locations per CSA Standard 30 and UL Standard 1203 for Class 1, Division 1 and Division 2 hazardous locations. Wetted parts are all 316L Stainless Steel (50 up to 10000 PSIG), 17-4PH (15000 & 20000 PSIG) for compatibility with a variety of media. Wetted materials and construction comply with the NACE MR0175 Standard. The KP46 Series explosion-proof pressure transmitter's fitting and sensing diaphragm are machined out of a single piece of material, so there are no welds, seams or O-ring seals, resulting in excellent long-term performance and stability. The case is factory sealed, making this pressure transmitter very rugged with excellent shock and vibration resistance.
-
Product
FTTP Multi-Port Output 1550nm External Modulation 47~862MHz
HT8500M
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HT8500M series, Multi-optical port output externally modulated transmitter, a research product which is designed for FTTx PON large area and multi-user access. HT8500M series, use high-power , low noise, narrow linewidth, continuous broadcast, DFB lasers. It can provide 4~10 way high linearity standard optical power output. It can connect 4~10 units high-power FTTB EDFA( Like Huatai HA5837-32). AS this product without EDFA, so each optical port can out put up to :CNR≥53.5dB, CTB≥-65dB, CTB≤-65dB, the high technical index.
-
Product
Noise & Vibration Analyzers
-
The NVA instrument is generally composed of a personal computer equipped with one or more data acquisition board, a conditioning interface and / or to the transmitters power and finally a series of libraries of application software dedicated to the type of measurement to be made. the type of personal computer can be either a desktop, notebook or portable and depending on the particular requirements, you can use the PXI architectures.
-
Product
Tunable System Sources
-
The Keysight N7711A and N7714A tunable lasers are single-port and four-port sources, available with C-band or L-band wavelength coverage. All models can reach any wavelength point within their specified wavelength in the C- and L-band range. The narrow linewidth and offset grid fine-tuning capability make them ideal sources for realistic loading of the latest transmission systems. In system loading applications, it may be preferable to grid-tune the lasers like system transmitters, simply by changing the channel index. The channel grid is adjustable to standard ITU-T grid spacing like 50 GHz, and to arbitrary grids. The Keysight N7711A and N7714A tunable lasers are available in a compact format with half-rack width and one rack-unit height. This format makes them the right choice for high channel-count system load applications.
-
Product
Signal Acquisition and Filtering Technology
SNAPTrack®
-
Built on a proven design, and with Pathfinder SAF Technology™ at its core, the SnapTRACK® offers RYCOM’s most advanced signal acquisition and filtering technology. The SnapTRACK® cable & pipe locator offers utility locators FrequencyFlex™ allowing users to adapt the system to their specific needs. Multiple active frequencies allow the user to accurately locate with a minimum of interference while maintaining the ability continue locating past faults and around conduit bends. Passive frequencies identify "live" and charged lines by their naturally occurring electromagnetic fields. The SnapTRACK® offers multiple passive frequencies -- 50Hz, 60Hz, Radio Frequency, Cathodic Protection Rectifier & CATV -- allowing line locating without the use of a transmitter.
-
Product
Fiber Transmitter With Fiber Amplifier
FTFA 822B - 824B
-
- Work as Transmitter & Fiber Amplifier- AGC - Automatic Gain Control- Built in RF Booster- Higher RF at next connected Node- Maintain MER/BER for Digital FTTH Transmission- High Quality DFB Lesers with Isolaters- Variable SLOPE Control- Output Wavelength : 1310nmPower Options :- 40V DC- 12V DC / 2 Amp- STB Adapter along with PSP- 7.4V, 2600 mAH Battery
-
Product
Temperature, Humidity, Bar. Pressure Transmitter
T7310
-
Built-in relative humidity, temperature, atmospheric pressure sensors. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy.
-
Product
Prop Shaft Torque Measurement Systems
-
Advanced Telemetrics International
ATi Telemetry Systems are typically used to transmit data from rotating shafts or machinery to a stationary receiver. The Miniature Strain Gage Transmitter can be attached to strain gages adhered to your shaft in order to transmit shaft torque and thrust while the system is running.
-
Product
DM 150-Watt Transmitter
Loc-150Tx
-
The Loc-150Tx, 150-Watt DM Transmitter is used primarily with the Defect Mapper (DM) Receiver, however it is also useful for those needing a low frequency, high output transmitter. Typically, the Loc-150Tx, transmitter (DM transmitter) is used to apply a signal current to the anode bed. The pipeline returns the signal via coating faults back to the transmitter. The Loc-150Tx transmitter is designed to be powered from CP (Cathodic Protection) stations, AC or external batteries, eliminating the need for internal batteries. This transmitter has a direct connection mode to apply the locate frequency onto the conductor. There is no clamp or induction mode.
