-
Product
Bidirectional DC Power Supply + Regenerative Load
62000D
-
Chroma Systems Solutions, Inc.
Chroma 62000D programmable bidirectional DC power supplies have both power source and load characteristics, two quadrant operation, and allows feedback of the power from the DUT. They can be used for testing renewable energy power systems including PV/storage hybrid inverters, power conversion system (PCS) on charging/discharging, and as a battery simulator. The 62000D also is a fit for testing power components used in electric vehicles, such as bidirectional on-board chargers (BOBC), bidirectional DC convertors, and DC-AC motor drivers, and power conversion simulation tests of batteries in both directions.
-
Product
±6 kV ANSI/ESDA/JEDEC 2-Pin HBM Tester
HBM-S1-B
-
High Power Pulse Instruments GmbH
*±6 kV Human-Body-Model (HBM) 2-pin tester according ANSI/ESDA/JEDEC JS-001 standard with C = 100 pF, R = 1.5 kΩ discharge network*True HBM: the classical discharge network of the HBM-S1-A according the standard ensures compliant waveforms for all load conditions*Optionally available upgrade for all HPPI TLP-3010C, 4010C, 8010A, and 8010C hardware systems and software (upgrade on request)*Suppression of trailing pulses*Integrated 10 kΩ charge removal resistor*Integrated DUT voltage and DUT current sensor for real time voltage and current monitoring*Integrated DC test DUT switchIntegrated hardware 50 Ω trigger output for high speed digital oscilloscopesIntegrated overvoltage protection of voltage sense and DC test interfaces for oscilloscope and SMU protection during high voltage HBM testing*Fast and efficient HBM measurements including transient waveform data management using the HPPI TLP software*Compact size 145 mm x 82.5 mm x 44 mm
-
Product
Solar Array Simulator
G5.SAS
-
The G5.SAS series are unidirectional sources. It was developed specifically for testing inverters and simulating solar arrays and is suitable for use in laboratories and on test benches. The modular and finely graded G5.SAS series is characterized by highly dynamic response times and a wide current-voltage range with an auto-ranging factor 3. The power supplies feature especially low capacitance values in the output filter stage and switchable earth leakage resistors for adaptation to the insulation measurement of the DUT.
-
Product
Automatic Fixture Removal
S95007B
-
Many devices do not have coaxial connectors and so they are put in fixtures in order to measure them in a coaxial environment. You must accurately remove the effects of the fixture to get a good measurement of the device under test (DUT). This option adds a powerful application wizard to guide you through characterizing a fixture and removing it from the measurement. The S95007B software is compatible with M980xA PXI Vector Network Analyzers.
-
Product
Vibration Unit Tester
BK2020B
-
We developed the BK2020B as an upgrade to our BK2020 to test the electrical specifications (RPM, current, drop pulse, start up voltage) of your cylindrical or coin type vibration units. You can also test vibration level, noise, isolation resistance, and the DC resistance. The DUT power supply and all measurement components are self contained, so external devices aren't needed and the tester uses DSP, making it capable of fast, highly accurate and reliable measurements. The BK2020B is very versatile. It can be set up as a stand alone machine, or used with a PC and software for access to more information, and to save the data for analysis. Either version is great on the product line but you may also use it for QA, QC and development.
-
Product
Electronics Functional Test
Functional Test
Functional test for productive manufacturing. Manufacturers of products enabled by electronics must assure proper operation prior to shipment. Bloomy’s line of universal test systems are ideal for functional test of your PCBAs and subassemblies, from the simplest to the most complex. The UTS family of products combines high-performance test instruments, switching, power control and mass-interconnect hardware with our robust UTS software suite into a low-risk, cost-effective and powerful test solution for your device under test (DUT).
-
Product
Bidirectional DC Power Supply
62000D
DC Power Supply
Chroma 62000D programmable bidirectional DC power supplies provide both power source and load characteristics. These two quadrant power supplies allow power from the DUT to be converted back to the utility grid and so are ideal for testing renewable energy power systems such as PV, storage, and EV inverters as well as a wide range of bidirectional power conditioning system (PCS) and may also be used as a battery simulator.
-
Product
Semiconductor Testing
-
The integrated PXI platform and the open interfacing provides extension capabilities for additional testing requirements like DUT specific resistors-networks or temperature sensors. The Test System comes with the ready-to-run GTSoftware package and allows easy programming of test sequences (GTbuilder) and fast execution in production/test mode (GTengine).
-
Product
PXIe-4112, 2-Channel, 60 V, 1 A PXI Programmable Power Supply
782857-01
Programmable Power Supply
The PXIe‑4112 is a programmable DC power supply with isolated outputs. It helps simplify the task of designing automated test systems for a wide range of applications—from aerospace and defense to automotive and component test—by eliminating the need to mix multiple instrumentation form factors in a given test rack. It also has standard output disconnect functionality that allows isolation from the device under test (DUT) when not in use, and remote sense to correct for losses in system wiring.
-
Product
Automated Test Interface
ATI-100
-
Matrix Test Equipment Incorporated
Now, with our ?New? Model ATI-100 you can turn your existing Matrix Signal Generator and Switchable Filter Bank into a full-blown DTS (Distortion Test System). Plug and play is the word, just plug in your Multiple Frequency Signal Generator, Switchable Filter Bank, Spectrum Analyzer, Oscilloscope, Power Meter, Frequency Counter, etc. to allow the following automatic testing with a single insertion of DUT (device under test
-
Product
Temp Characterized CalPod, 20 GHz
85531B
-
CalPods provide a new and unique way to quickly and easily refresh a network analyzer calibration, at the push of a button and without removing the DUT or re-connecting standards. Very useful in thermal chamber testing, where it is desired to remove the thermal effects of the test cables and connectors from the DUT’s response, and where it is impractical to stop the thermal testing to perform a normal re-calibration.
-
Product
Emulate Test in simulation
STIL-VT
-
Emulate test patterns in simulation environment with DUT simulation model. The simulation allows pre-silicon debug of test patterns. Reads the intermediate STIL format of tester patterns and creates a Verilog /VHDL simulation test bench. (A sub-set of Virtual tester solution)
-
Product
FPGA Image Processing (IP) Development Kit
ProcVision
-
Gidel’s Vision Pro Development Kit is an optimal solution for developing,validating, demonstrating and evaluating Image Processing (IP) andpipeline designs on FPGA.The suite is designed to provide a complete and convenient envelop enablingthe developer to focus strictly on the proprietary image processingdesign. The entire Vision Pro flow is within a single FPGA, independentof the final target application(s). The Vision Pro flow is composedof a pipeline that streams simulated data to the user image processingdesign under test (DUT) and then captures the design’s output streamfor displaying, storing, analysis and/or co-processing on host software.The entire process is performed on a single FPGA without the need foradditional peripheral connectivity or tools.Vision Pro suite is plug-and-play enabling the developer to begin at oncethe IP design development and validation. A simple design example providesthe developer immediate hands-on familiarization with the systemflow and supporting tools. The final design can be ported to any IntelFPGA device or other vendors’ devices (FPGA or ASIC) by replacing basiclibraries. To significantly reduce compilation time, initial design developmentmay be on a small FPGA device and later compiled for the targetdevice(s). The target implementation may use any FPGA board. For a fullImaging/Vision system solution, Gidel offers a number of off-the-shelfgrabbers and FPGA accelerators that are designed to utilize these imageprocessing blocks and Gidel Imaging Library (GIL).
-
Product
HV-Test System for Capacitor Packages
-
The system is used to characterize the leakage currents of capacitor packages. LXinstruments implemented a project-specific PCBA for the required HV switching. The measurement technology consists of Keithley source meters and USB based devices. The DUT adaptation with safety technology was realized in cooperation with ATX.
-
Product
Milli-OHM Meter
MR-30
-
*Double LCD Display*300,000 counts resolution*Measurement Range: 30mΩ~3MΩ*0.05% accuracy*20 Standard User setting memory sets*Sorting function and Relative percentage function*PASS/FAIL test result alarm*Computer Remote Manual and Auto Scan function*Manual and Auto Channel select*Sampling Rate: 30 sample/sec*High Resolution Temperature compensation and measurement*DUT Four-wire method*USB interface
-
Product
Load Simulator
Simulator
The load system is intended for testing satellite power supply systems; due to the integration with a solar array simulator and a battery simulator, it can perform validation and commissioning of satellite power supplies. The system is equipped with regenerative electronic loads and customer-specific high-power switching matrices for routing the DUT channels to the relevant loads. The individual voltages and currents for each channel can be read back via a Keysight Technologies switch mainframe.The system is equipped with high electrical power; its loads are capable of feeding the energy back into the power grid.
-
Product
Signal Generator Frequency Extenders
FES
-
These frequency extension modules easily connect to the output of your signal generator so you have high-performance source for your DUT characterization activities. Characterize your DUT with the confidence that the superior performance in terms of output power, spurious and harmonic will provide product accurate results.
-
Product
PXIe-4145, 4-Channel, ±6 V, 500 mA Precision PXI Source Measure Unit
782435-01
Source Measure Unit
PXIe, 4-Channel, ±6 V, 500 mA Precision PXI Source Measure Unit - The PXIe-4145 is a 4-channel source measure unit (SMU) ideal for high-pin-count applications. It features 4-quadrant operation, and each channel has integrated remote (4 wire) sensing for accurate measurements. The fast sample rate of the PXIe-4145 can reduce measurement times, capture transient device characteristics, and allow quick I V characterization of devices under test (DUTs). With a high-speed sequencing engine, you can synchronize all these SMUs with each other or with other instruments such as switches or high-speed digital test modules. Additionally, you can tune the PXIe-4145 response to any load to achieve optimum responses with maximum stability and minimum transients using SourceAdapt technology.
-
Product
Security Testing
-
Security/negative testing is typically conducted during development to highlight how a DUT handles abnormal conditions like very high traffic load, different frame sizes (incl. undersized and oversized frames), framed with different IFG settings, various types of errors and deviation of the signal frequency, as well as various DDoS attacks.
-
Product
Universal Function Test System for Industrial Electronics
Test System
General functional test system based on LXI instrumentation for high mix / low to medium volume manufacturing. DUTs are tested which are mainly used as communication and measurement modules in power plant technology, grid management and electrical drives.The system has a Virginia Panel adapter interface to which various desk adapters can be docked, including automated contacting of the DUTs. A camera for the verification of light emitting diodes on the test object is integrated in the adapter interface.
-
Product
Detector And FPA Testing
-
The FPA Test Set (FPATS) interface to the detectors under test (DUT’s) is via a custom pedestal plate which provides both a conductive heat path to both the individual DUT’s as well as the field of view limiting aperture plate. This custom pedestal plate protrudes through the customer provided DUT interface printed circuit board (PCB) and makes physical contact with the rear of the DUT packages and the aperture plate when the FPATS is in the closed position. The pedestal plate is mounted to the ambient source plate and its temperature is actively driven by this subsystem.
-
Product
Large-size Hybrid Reverberation / Anechoic Chamber
F-Series
-
The F large-size hybrid Reverberation/Anechoic Chamber represents the most versatile OTA test system in the market today. With the same unique test features of their E Series RC counterparts, the F-Series can also test large form-factor devices under test (DUTs) like laptops, large TV sets, solar and trash compactors, drones, fridges or washing and vending machines, among others. With up to 16x16, 8DLCC and DUTs up to 2m and 500 kg including full-body phantoms in a turntable, the F Series also expands the frequency range down to cover 200 MHz up to 40 GHz frequency ranges and the test modes to include EMC, BS, small cell, eNodeB and Virtual Drive Testing over the air (VDT-OTA). In an again unheard-of feature, the F-Series is also reverse-convertible into an Anechoic chamber, allowing Far Field (FF) and Spherical Near Field (SNF) radiation patterns, efficiency and gain measurements and pre-5G testing of antennas and devices. Conversion from RC to AC or vice versa can be performed within half a day.
-
Product
Pneumatic Test Pump Kit
700HPPK
-
The Fluke Calibration 700HPPK Pneumatic Test Pump Kit generates and adjusts pneumatic pressures up to 21 MPa (3000 psi), without requiring a nitrogen bottle or other external pressure supply. It supplies pressure to devices under test (DUTs) that include transmitters, controllers, pilots, digital and analog gauges, and more. It’s the perfect solution for generating high pressure in the field, where conditions and operating surfaces can vary. The 700HPPK is the ideal choice for calibration technicians, test engineers, and instrument technicians working in industries like natural gas transmission and distribution, process, aerospace and defense, who need a simple-to-use, safe and portable pressure source that they can depend on in a wide variety of conditions.
-
Product
IOL & Power Cycling Test Systems
Test System
Our IOL & power cycling systems increase measurement quality and throughput and reduce testing costs on an open platform. The focus is on seamless monitoring and precise determination of all parameters of each DUT. In addition, the systems are equipped for the special requirements of wide-bandgap technology.
-
Product
DC Power Module, 5V, 20A, 100W
N6741B
Power Module
The Keysight N6741B is a 100 W basic DC power module that provides programmable voltage and current, measurement and protection features at a very economical price, making these modules suitable to power the DUT or to provide power for ATE system resources such as fixture control.
-
Product
PXIe-4154, 2-Channel, 8 V, 3 A PXI Programmable Power Supply
781155-01
Programmable Power Supply
2-Channel, 8 V, ±3 A PXI Programmable Power Supply—The PXIe‑4154 is a specialized programmable power supply for battery simulation. It is designed to simulate a lithium‑ion battery cell’s transient speed, output resistance, and 2‑quadrant operation (source/sink). Critical to many RF and wireless applications, the simulator’s fast transient response time allows it to rapidly respond to changes in load current with minimal voltage dip, which makes the PXIe‑4154 ideal for powering devices under test (DUTs) such as RF power amplifiers, cellular handsets, and a variety of other mobile devices. To model the behavior of a battery more accurately, you can use the onboard programmable output resistance to simulate a battery’s internal resistance. For quiescent and standby current measurements, the PXIe‑4154 features integrated current measurement.
-
Product
AC Ground Bond Tester
446
-
Our 446 model is a 4-in-1 tester with AC Hipot, DC Hipot, Insulation Resistance, and Ground Bond capabilities. This tester features a simple design and easy-to-use interface, reducing setup time and increasing production-line throughput for your application. The 446 is equipped with multiple memories and an optional USB port for remote BUS communication so you can quickly perform tests on a variety of DUTs from the front panel or with a PC. Add to user safety by equipping your tester with Personal Protective Equipment (PPE) via the built-in safety interlock.
-
Product
Qualification Hardware & Sockets
-
Reltech Limited holds over 35 years’ experience in the design and manufacture of all types of qualification test hardware. Our advanced technology products include: HTOL Boards (Mother and Daughter cards) Burn-In Boards HAST Boards THB (humidity) Boards Burn-In Modules and frames Dynamic Driver cards (Digital, Analogue and Mixed signal) Back Planes Voltage regulator cards Custom electro-mechanical assemblies DUT Cassettes and test Fixtures
-
Product
Stator Testing System for EV Motor
EVT531
-
Shanghai Dean Electrical Co., Ltd
To meet the standard test projects requirement of the international companiesTo control and analysis the programs will reduce the human careless and misjudgmentEasy to edit environment and easy to learnIt can test multiple sets of DUTs simultaneouslyWhen there are several DUTs are tested, it could identify the undesirable sets individuallyThe Impulse/Surge with waveform comparison is a non-destructive analysisPolarity testMaximum saved files will be up to 100 setsIt provides the password functionSpeeding test could save time and improve efficiencyChinese and English pages can be arbitrarily switched
-
Product
Impedance Analyzers
-
A/D converted input signals undergo discrete Fourier transform (DFT) to calculate complex impedance values and obtain parameters and characteristics specific to the DUT, such as its capacitance, inductance and quality factor. Original NF algorithms are also applied to allow equivalent circuits made up of R, L and C along with the constants for those circuits to be estimated from the complex impedance spectrum obtained by sweeping the frequencies.
